WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ford Edge

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

180 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
SSM 543662025-11-19. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
SSM 523142024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
22N12 S12023-06-06. Service bulletin. EQUIPMENT; POWER TRAIN. Certain 2015-2018 Model Year Edge, 2019-2020 Fusion and MKZ Vehicles Equipped with a 2.0L EcoBoost Engine and 6F35 Transmission Rattle Noise at the Transmission Bellhousing Area Flexplate Cracks REASON FOR THIS SUPPLEMENT Aftermarket torque converters are no longer approved for this program, Ford part number DG9Z- 7902-H is readily available Customers will be mailed a second owner letter in June 2023 Added Attachment IV Mobile Repair Assessment Added Pick-up and Delivery information for Participating Dealers Updated Technical Instructions, Verbal Authorization needed prior to parts being ordered by SSSC
22N122022-08-30. Service bulletin. POWER TRAIN. Certain 2015-2018 Model Year Edge, 2019-2020 Fusion and MKZ Vehicles Equipped with a 2.0L EcoBoost Engine and 6F35 Transmission Rattle Noise at the Transmission Bellhousing Area – Flexplate Crack In some of the affected vehicles, a cracked flexplate may cause a rattling noise at start up and/or while driving the vehicle. The rattling noise may vary with vehicle operation and is most apparent with transmission in drive at idle speed. Some customers may also feel a powertrain vibration, encounter an inability to start the engine, or experience a loss of motive power while driving.
TSB 22-20662022-05-02. Service bulletin. POWER TRAIN. Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
SSM 500492021-09-04. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:DOGS/SYNCHROS. Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.
TSB 21-21522021-06-03. Service bulletin. POWER TRAIN; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
SSM 498212021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-20332021-04-03. Service bulletin. POWER TRAIN. Some 2013-2016 Fusion, 2013-2018 C-MAX, 2013-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.
TSB 20-22122020-09-02. Service bulletin. POWER TRAIN; EQUIPMENT; ENGINE AND ENGINE COOLING. This article supersedes TSB 19-2236 to update the parts list. Some 2015-2018 Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise. This may be more noticeable at idle. This may be due to a flexplate crack around the crankshaft. To correct the condition, follow the Service Procedure steps to replace the flexplate, transmission fluid pump, and torque converter.
SSM 484232020-01-08. Service bulletin. POWER TRAIN. Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-22362019-09-06. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER; POWER TRAIN; EQUIPMENT. Some 2015-2018 Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise. This may be more noticeable at idle. This may be due to a flexplate crack around the crankshaft. To correct the condition, follow the Service Procedure steps to replace the flexplate, transmission fluid pump, and torque converter. Follow the Service Procedure steps to correct the condition.
SSM 479762019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
TSB 19-20172019-04-08. Service bulletin. POWER TRAIN; POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT:SEAL. Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
TSB 19-20172019-04-01. Service bulletin. POWER TRAIN; EQUIPMENT. Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
SSM 475762018-11-19. Service bulletin. EQUIPMENT; ENGINE; POWER TRAIN. Some 2015-2018 Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise at idle. This may be due to a flexplate crack around the crankshaft. To resolve this concern, verify that the flexplate is cracked around the crankshaft using the inspection plate and a mirror. If the flexplate is cracked, replace the transmission fluid pump, flexplate, flexplate bolts and torque converter. Refer to Workshop Manual (WSM), Section 303-01A and 307-01. When replacing the torque converter, ensure that the torque converter pilot hub is lubricated with Multi-Purpose Grease XL-5-A (ESB-M1C930-B) prior to reassembly. For claiming, use causal part 6375 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.
SSM 473982018-09-10. Service bulletin. POWER TRAIN; ENGINE; EQUIPMENT. Some 2015-2018 Edge vehicles equipped with a 2.0L EcoBoost and 6F35 transmission may exhibit a rattle noise from the transmission bellhousing area while running. This may be the result of a cracked engine flexplate. When replacing the flexplate, lubricate the torque converter pilot hub with Multi-Purpose Grease XL-5-A (ESB-M1C93-B) before reassembling. Make sure the transmission locator dowel pins are correctly installed. If the dowel pins were pulled out of the engine block, new dowel pins will need to be installed in the engine block. Failure to do so could result in a repeat repair. Refer to Workshop Manual (WSM), Section 307-01A. Engineering is investigating, monitor OASIS for updates. To assist with the investigation use the Report a Vehicle Concern link at the bottom of the OASIS report and fill out the form.
tsb18-22122018-09-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some 2016-2018 Edge vehicles equipped with a 2.0L EcoBoost engine built on or before 12-Mar-2018 may exhibit an illuminated MIL with DTC P0036 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
SSM 470002018-06-11. Service bulletin. ENGINE; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 471702018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB18-20972018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2016-2017 Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit an illuminated MIL with DTC P0036 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
tsb17-22142017-12-14. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017 Edge vehicles equipped with a 2.0L Gasoline Turbocharged Direct Injection (GTDI) engine built on or before 8-Sep-2017 may exhibit an illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in powertrain control module (PCM) memory. Reprogram the powertrain control module (PCM) to the latest calibration using IDS or Ford J2534 Diagnostic Software (FJDS) release 107.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.