WenmarOpen by Wenmar Pro

Service bulletins for the 2025 Ford Bronco

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

103 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
SSM 548572026-05-26. Service bulletin. FUEL/PROPULSION SYSTEM. 2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly.
SSM 548562026-05-26. Service bulletin. FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; SERVICE BRAKES. Some 2025-2026 Bronco vehicles may exhibit a condition where cruise control is inoperative and/or an "Adaptive Cruise Control Not Available" message is displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0422:00 stored in the anti-lock brake (ABS) module. If a vehicle exhibits this condition, this may be due to an incorrect configuration programmed to the ABS module during an attempt to change tire size. <br /><br /> The Ford Performance ProCal 4 tool is the only approved tool that can be used for properly adjusting the tire size calibration. Vehicles originally equipped with 30-inch tires that are being upfit with 35-inch tires should be set to 615 revolutions per mile in the Ford Performance ProCal 4 tool under Diagnostics and Tools > Tire/Gear Adjust. Any other concerns related to tire size calibration that exhibit this condition, contact the Ford Performance Techline as outlined in the Ford Performance ProCal 4 tool instructions. <br /><br /> This limitation in tire size calibration is due to the software in the ABS module.
SSM 548482026-05-26. Service bulletin. SERVICE BRAKES. Some 2025 Bronco Raptor vehicles may exhibit a concern where certain selectable drive modes (G.O.A.T. modes) are unavailable after the ABS module receives a software update. Customers may also report that the "Offroad" mode is not visible and/or after switching to the "Baja" or "Rock Crawl" drive modes, the vehicle returns back to "Normal" mode. To correct this condition, download and run the "ABS - Anti-Lock Brake System (ABS) Module Software Update" application using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming use causal part 2005 and labor operations 2219D and 2219D44.
SSM 548472026-05-26. Service bulletin. SERVICE BRAKES. Some 2025 Bronco non-Raptor vehicles may exhibit a concern where certain selectable drive modes (G.O.A.T. modes) are unavailable after the ABS module received a software update. Customers may report that the vehicle is missing the "Mud/Ruts" and/or "Sand" drive mode(s). To correct this condition, download and run the "ABS - Anti-Lock Brake System (ABS) Module Software Update" application using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming use causal part 2005 and labor operations 2219D and 2219D44.
TSB 26-21852026-05-14. Service bulletin. ELECTRICAL SYSTEM; UNKNOWN OR OTHER. This bulletin supersedes 25-2621. Reason for update: add 2026 model year vehicles and Transit, update the causal part number (15604), update the Service Procedure, update the service labor operations for 2023 F-Super Duty, and add service labor operations for Transit. Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
SSM 548072026-05-14. Service bulletin. SUSPENSION; ELECTRICAL SYSTEM; UNKNOWN OR OTHER; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. Some 2025-2026 Bronco vehicles may exhibit various cruise control, pre-collision and/or front stabilizer bar disconnect related warning messages displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0418:86 stored in the image processing module A (IPMA). DTC U0415:00 may also be stored in the CHCM. <br /><br /> If wheel speed sensor specific DTCs are present in the anti-lock brake (ABS) module and/or warning messages other than those listed above are present, this SSM does not apply. Refer to the Workshop Manual (WSM) for normal diagnostics. <br /><br /> If a vehicle exhibits this condition, carefully inspect the rear wheel speed sensors for correct installation with the rear wheel speed sensor body seated flush against the axle housing. Repair or replace the affected rear wheel speed sensor as needed, clear the DTC, and retest. Refer to WSM, Section 206-09. <br /><br /> This condition does not affect vehicle durability, and additional diagnosis or service is not recommended at this time. Replacement or reprogramming of the IPMA and/or ABS modules will not resolve this
SSM 547942026-05-08. Service bulletin. STRUCTURE:BODY. Some 2024-2025 Bronco vehicles may exhibit a wind noise that has been isolated to the hard top front panel seal. An updated part has been released for service (5-door: M2DZ-78503A22-C and 3-door: M2DZ-98503A22-C). Refer to Workshop Manual, Section 501-18B Hard Top > Removal and Installation > Hard Top Front Panel Seal.
PCM-26.7.0 Bronco2026-05-01. Over-the-air update. POWER TRAIN. Quality improvements include: -Powertrain Control Module calibration update to address a potential false warning light
26P042026-04-30. Other. POWER TRAIN. Recommended Repair Prior to Sale Customer Satisfaction Program 26P04 Certain 2025 Model Year Bronco and Ranger Vehicles with 2.7L Engine Setting Diagnostic Trouble Code (DTC) P04DB Powertrain Control Module Software Update
SSM 547812026-04-28. Service bulletin. POWER TRAIN. Some 2021-2025 Bronco vehicles built on or before 09-Sep-2025 may require replacement of the ambient air temperature sensor for various concerns. Diagnostic trouble codes (DTC) P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM). A concern has been identified in TSB 26-2006 that previously instructed replacement of the incorrect ambient air temperature sensor for the vehicle application. Monitor Professional Technician System (PTS) for updates.
SSM 547722026-04-28. Service bulletin. VEHICLE SPEED CONTROL; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; POWER TRAIN. Some 2025-2026 Bronco vehicles may exhibit various cruise control, pre-collision and/or front stabilizer bar disconnect related warning messages displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0418:86 stored in the image processing module A (IPMA) and no wheel speed sensor specific DTCs present in the anti-lock brake (ABS) module. DTC U0415:00 may also be stored in the CHCM. If a vehicle exhibits this condition, carefully inspect the rear wheel speed sensors for correct installation with the rear wheel speed sensor body seated flush against the axle housing. Repair or replace the affected rear wheel speed sensor as needed, clear the DTC, and retest. Refer to Workshop Manual (WSM), Section 206-09. If the condition persists, advise the customer that Engineering is working on a software robustness solution that is expected to be available Q2 2026. <br /><br /> This condition does not affect vehicle durability, and additional diagnosis or service is not recommended at this time. Replacement or reprogramming of the IPMA and/or ABS modules will not resolve this condition.
SSM 547652026-04-28. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. Some 2025-2026 Bronco, Bronco Sport, F-Super Duty, Maverick, Mustang, Mustang Mach-E, Ranger and Transit vehicles may exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, engineering is currently working on a solution for this condition that is expected by September 2026. Replacement or reprogramming of the ACM and or audio digital signal processing module (DSP) may not resolve this condition at this time. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a customer's vehicle exhibits this concern, submit a Vehicle Concern Report.
TSB 26-20062026-04-22. Service bulletin. POWER TRAIN; UNKNOWN OR OTHER. Some vehicles listed in the model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM).
SSM 547332026-04-14. Service bulletin. SERVICE BRAKES. Some 2025-2026 Bronco/Expedition/Navigator/F-150/Ranger vehicles may exhibit a "Check Brake System" message in the instrument panel cluster (IPC) and/or an illuminated anti-lock brake system (ABS) indicator with diagnostic trouble code (DTC) C0563 stored in the ABS module. This may be due to air still trapped in the system after prior bleeding attempts and/or brake service mode being enabled. The applicable pinpoint test (PPT) in Workshop Manual (WSM), Section 206-09 has been updated to improve diagnostics for this concern. Make sure the latest software version of Ford Diagnosis and Repair System (FDRS) is being used when performing the brake system pressure bleeding routine.
SSM 547202026-04-10. Service bulletin. ELECTRICAL SYSTEM; LANE DEPARTURE: BLIND SPOT DETECTION. Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
SSM 547042026-04-06. Service bulletin. FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; ELECTRICAL SYSTEM. Some 2025-2026 Bronco vehicles may exhibit a "Cruise Control Not Available" or "Adaptive Cruise Control Not Available" and/or "Pre-Collision Assist Not Available" message displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0418:86 stored in the image processing module A (IPMA) and no DTCs present in the anti-lock brake (ABS) module
SSM 546862026-04-06. Service bulletin. UNKNOWN OR OTHER. Some 2024-2026 Bronco vehicles that have the dealer installed option (DIO)/accessory trailer tow kit installed may exhibit a condition where the trailer module (TRM) is not detected, or a "Procedure Unsuccessful" message is displayed after running a configuration application using the Ford Diagnosis and Repair System (FDRS) scan tool. This may be due to any of the following issues:<br /><br /> -The FDRS scan tool version is not at the latest software level. To correct this condition, run the "Towbar Configuration" application using the latest software version of the FDRS scan tool.<br /><br /> -The "TRM - Trailer Module (TRM) Configuration" application being run instead of the "Towbar Configuration" application. Accessory TRMs are preprogrammed and only the "Towbar Configuration" application should be run to configure the TRM properly for trailer tow capabilities. Too many attempts to program the TRM using the "TRM - Trailer Module (TRM) Configuration" application may result in a faulted TRM.
SSM 546732026-04-06. Service bulletin. VEHICLE SPEED CONTROL; ELECTRICAL SYSTEM. Some 2025-2026 Bronco Badlands and Raptor only vehicles may exhibit a "Cruise Control Not Available" or "Active Cruise Control Not Available" message displayed in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U0418:86 stored in the image processing module A (IPMA) and no DTCs present in the anti-lock brake (ABS) module.
SYNC-26.2.4.11 Bronco2026-04-03. Over-the-air update. ELECTRICAL SYSTEM; VISIBILITY/WIPER. "26S09 Recall Remedy -Update to enable rearview camera image to display when in reverse after infotainment screen thermal shutdown"
IPC-25.21 Bronco2026-04-01. Over-the-air update. VISIBILITY/WIPER; UNKNOWN OR OTHER; ELECTRICAL SYSTEM. "25SC3 Recall remedy: -Instrument Panel Cluster update to prevent a potential black screen at start up"
25N172026-03-27. Other. LANE DEPARTURE: BLIND SPOT DETECTION; BACK OVER PREVENTION: WARNINGS; BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING; UNKNOWN OR OTHER. Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
SSM 546092026-03-04. Service bulletin. ELECTRICAL SYSTEM; UNKNOWN OR OTHER. Some 2025 Bronco vehicles equipped with a 7-speaker audio system (minor feature code IDBAL) may exhibit an intermittent no audio condition. To confirm a vehicle is built with a certain minor feature code, review the build information by clicking "Additional Information" under Vehicle ID Tab > Vehicle Information, or double-clicking the vehicle identification number (VIN) in the upper left corner on Professional Technician System (PTS). To correct this condition, reprogram the audio front control module (ACM) using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming use causal part 18806 and labor operations 12651D and 12651D4.
SSM 545932026-02-27. Service bulletin. ENGINE; POWER TRAIN; FUEL/PROPULSION SYSTEM. Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and/or may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the high-pressure fuel pump causing fuel to enter the crankcase and reduce fuel pressure in the direct injection fuel rail. Diagnose this condition using Pinpoint Test HP located in Workshop Manual (WSM), Section 303-04. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. Repair as necessary outside of this article. For claiming, if high-pressure fuel pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article.
SSM 545922026-02-27. Service bulletin. POWER TRAIN. For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
SSM 546012026-02-27. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY; UNKNOWN OR OTHER. Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.