Service bulletins for the 2010 Dodge Ram
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
267 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| 54931 | 2019-07-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. TAILPIPE - EXHAUST |
|---|---|
| 9003357 | 2019-07-15. Service bulletin. ENGINE; EQUIPMENT. ADAPTER, Engine Oil Filter (Pentastar V6) Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. |
| 18-093-15 | 2019-05-20. Service bulletin. ELECTRICAL SYSTEM; ENGINE; SERVICE BRAKES, HYDRAULIC; POWER TRAIN. Flash: MIL Illumination With Transmission And Driveability Improvements This bulletin involves flash reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience a MIL illumination. Upon further investigation the technician may find that any of the following erroneous Diagnostic Trouble Codes (DTCs): ? U0140 - Lost Communication With Body Control Module. 2010 DJ 5.7L (Sales Code EZC) Attempting to clear this DTC will be unsuccessful. ? P050D - Cold Start Rough Idle. ? P2181 - Cooling System Performance has been set. ? P0935 - Line Pressure Sensor Circuit High. All RFE transmissions. P0300 through P0308 - Multiple and Single Cylinder Misfire. This condition can occur when the vehicle is started cold and the driver immediately places the vehicle in drive and applies heavy throttle. Driveability and Transmission improvements are also included with this software release. These changes consist of the following: ? Enhanced clutch protection for more robust torque management during repeated fore and aft movement (rocking vehicle). All engines. ? A revised torque convertor lockup schedule that will reduce transmission temperatures in Tow/Cruise mode. All models equipped with RFE transmission. ? A Clunk sound or feel a shudder when the cruise control resume switch is pressed. This condition is most noticeable after the brakes were pressed to cancel cruise control and then the resume switch is pressed. All models equipped with RFE transmission. ? A shudder or shaking feeling when a wide open throttle (WOT) event is performed by the customer. This is most noticeable after the transmission downshifts during the WOT event. This condition will stop once the transmission upshifts. All models equipped with RFE transmission. ? A shudder or shaking feeling when accelerating from a stop under moderate throttle. This condition will stop once the transmission upshifts. All models equipped with RFE transmission. |
| 25-004-15 | 2018-12-17. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE. On Board Diagnosis (OBD) Monitor Readiness |
| 13284 | 2018-12-17. Service bulletin. ENGINE. Title Filter - Engine Oil Start Date: 10/23/2015 7:00 AM End Date Message You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part number: 68109834AA. Replacement part number is: 68229402AA. 68229402AA is designed to work on both DS and W K with 3.0L Ecodiesel(EXF)in NAFTA. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com. |
| 68080819A | 2018-11-26. Service bulletin. ENGINE. Camshaft Position Sensor If replacing a camshaft position sensor for P0340 and/or P0344 fault codes, please review information below and contact Andrew Action on his cell phone: (248) 421- 4130. If no response is received within 15 minutes, please continue with repair.~ Before clearing any codes please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Andrew Acton by email: andrew.acton@fcagroup.com~ Instructions to access CamCrank Sync Event Monitor:~ - From wiTECH main screen~ - Monitors tab~ - OBDII Monitors~ - Select Cam Crank Synchronization Event Monitor from the list~ - Should bring up 3 or 4 pages of data~ - Click on create PDF icon in lower right corner~ - email PDF to andrew.acton@fcagroup.com |
| 68079375A | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Crankshaft Position Sensor Before replacing this part due to a P0335 fault code, please contact Andrew Acton at cell (248) 421-4130. Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data. |
| 05191925A | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked. |
| 05149141A | 2018-11-26. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Camshaft Position Sensor If replacing a camshaft position sensor for P0340, P0344, P0345, P0349, P0365, P0369, P0390 or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com |
| 04861963A | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT. Evaporative System Integrity Monitor switch (ESIM) Prior to replacing this component on a 2015 Dodge Journey (JC), please call Bob Bruni at cell (248) 736-8958. If a response is not received within 15 minutes, then continue with the necessary repair. |
| 22842 | 2018-06-11. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. 05187880AC - Inspect and Return: Relay Assy - Heater Intake Air You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016. |
| 20610 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. P/N 04573460 - Inspect &Return: Rocker Assy - Intake Valve RT You have been identified as either having stock, or have stock in transit to your dealership. Please return part number 04573460 which have a packaging date of 2016-06-13. Reference attached picture for reference. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016. |
| 17006 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. 68085119AE,Inspect and Return: Exhaust Pipe Assy - Frt W/Catalytic Converter You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com. |
| 16887 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. Return: ALTERNATOR - ENGINE You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com |
| 9002688 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. 68069384A$, R8069384A$, 68086182A$, R8027067A$, RL002012A$ - Gasket, Cylinder Head Cover Before replacing injectors for Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~ |
| 09-001-13 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE. Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components. |
| 30731 | 2018-06-11. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. 04627694AA Purge Control - Valve You have been identified as either having stock, or have stock in transit to your dealership. Suspect stock of part number: 04627694AA must be returned. See attached for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017. |
| 9001762 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Part Description: Thermostat, Engine Issue Description: Important! There has been an application change to the Cummins turbo diesel thermostat. When replacing a thermostat confirm the correct replacement is choosen.~ 2010, 2011, and 2012 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature has been increased to 200 degrees requiring thermostat 68067109AA.~ 2009, 2013, and 2014 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature is 190 degrees requiring thermostat 68005464AA.~ These thermostats are not interchangeable and doing so will result in reduced engine performance. |
| N0802072013 | 2018-06-04. Service bulletin. EQUIPMENT; ENGINE; POWER TRAIN. Advanced Field Action Communication ? N0802072013 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2009 through 2012 model year: (DS) Ram Truck (ND) Dodge Dakota (HB) Dodge Durango (HG) Chrysler Aspen NOTE: All of the above involved vehicles are equipped with a Chrysler 9.25? rear axle (sales code DRB) or C235 rear axle (sales code DRN). The above vehicles may have been built with a rear axle pinion nut that can loosen, which could result in the rear axle locking up. This could cause a loss of vehicle control and/or a crash with little warning. Chrysler will conduct a voluntary safety recall on all affected vehicles to install a rear axle pinion nut retainer. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. |
| 9002688 | 2018-06-04. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:WIRING; ENGINE AND ENGINE COOLING. 68069384A$, R8069384A$, 68086182A$, R8027067A$, RL002012A$ - Gasket, Cylinder Head Cover Before replacing injectors for Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~ |
| 09-001-13 | 2018-06-04. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components. |
| 18-022-13 | 2018-05-21. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. Cummins 6.7L Turbo Diesel Common Diagnostic Process New 6.7L Cummins®Turbo Diesel Common Diagnostic Process is now available as part of the standard diagnostic process located in TechCONNECT>Service Info. |
| 25-001-13 REV. A | 2018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. MIL Illumination Due to P2000, P2A00 and/or P2A01 FRONT O2 sensor. Customer may experience MIL illumination. Further investigation by the technician may find one or more of the following DTC(s) present: P2000 - NOX Absorber Efficiency Below Threshold - Bank 1. P2A00 - O2 Sensor 1/1 Circuit Performance. P2A01 - O2 Sensor 1/2 Circuit Performance. |
| 09-001-13 | 2018-02-21. Service bulletin. ENGINE. Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components. |
| RL108213A$ | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~ |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.