WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Dodge Durango

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

282 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
21-009-17 REV. A2018-06-11. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: During an engine limp mode condition, the transmission remains in a fixed gear.The following software enhancement is also available: Transmission shift quality enhancement.
18-024-17 REV. A2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.
14-001-17 REV. A2018-06-11. Service bulletin. FUEL SYSTEM, GASOLINE; POWER TRAIN. Poor Vehicle Acceleration This bulletin involves test driving the vehicle and if required, replacing the fuel pump module. The customer may notice the vehicle has poor acceleration and/or the transmission will not upshift under Wide Open Throttle (WOT). This can be caused by low fuel flow from the fuel pump module.
90032732018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Trans Pan or Gasket If your repair requires replacing one of the two part numbers for a leak, prior to the repair please call Enzo Piazza at cell (248) 467-9163. If you cannot reach Enzo within 15 minutes proceed with the repair. Enzo needs to know the location of the leak, if the bolts were torqued, if there is sealer skip, or anything that may be pertinent to the cause of the leak. Photos would be very helpful and can be sent to Enzo's cell phone or his email. Enzo's e-mail address is enzo.piazza@fcagroup.com.
90035842018-06-11. Service bulletin. STEERING. Electric Power Steering Gear If any of the following DTCs exist, it is okay to replace the steering gear: C2217-00, C15C1-00 (EPS Mechanical Performance) or C15DB-00 (Latch Active) otherwise perform the following; 1) Electrical, Communication or DTC (other then above) issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of Vehicle Scan Report (VSR) to be emailed to the above address. 2) Noise or Mechanical issue please contact: Ruth Delong @ cell (810) 569-0354.~ If you do not receive a return call within 15 minutes, proceed with the repair.~ Please be sure to attach a copy of the Vehicle Scan Report on the repair order
90036962018-06-11. Service bulletin. STRUCTURE:BODY:DOOR. Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
90036942018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
90036812018-06-11. Service bulletin. SEAT BELTS. Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
90036692018-06-11. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Auto Trans Rotary Electronic Shifter The rotary shifter is designed to actuate a motor within the device whenever the driver places their foot on the brake, with the car in Park (or Neutral). This generates a noise with each brake press/release. Therefore, even after replacing the shifter for a noise complaint, the replacementpart will also have a characteristic noise generated whenever the driver steps on the brake. Before performing a repair procedure for a noise complaint, please perform a subjective analysis of the noise coming from the rotary shifter. If the shifter noise is deemed abnormal sound (has an uncharacteristic buzz or grind), please proceed with normal replacement procedure. If so equipped, record the sound with a handheld microphone, or cell phone, and if noise is above 54dB @ 30cm away from the knob, please proceed with normal replacement procedure. For any further questions, please contact Theodore Kahiya at cell (519) 300-2443.
90036872018-06-11. Service bulletin. SEAT BELTS. Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
90036892018-06-11. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Cleaner For A/C Evaporator Before using deodorizer to remove HVAC or evaporator odor, call Ken Deneau at cell (248) 765-0288. If no response in 15 minutes, please continue with repair
90037492018-06-04. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. RA2 Radio 5" Uconnect Before replacing this radio, make sure you can reproduce the customer issue. If the radio is locked up, has a blank screen, or no sound, please perform a vehicle battery reset. If radio functionality is resumed, return the vehicle to the customer. If there are any questions or concerns or the vehicle has been in for repair for the same radio concern more than once, please call Rick Gordon at Cell (248) 630- 6281. If no response in 15 minutes, proceed with repair.
90037432018-06-04. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY. Radiator Before replacing the radiator call Wes Youkhana at FCA Auburn Hills cell: (248) 564-8595 to answer a few questions. If no response in 15 minutes, please proceed with repair.
90033572018-06-04. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.
90037262018-06-04. Service bulletin. FUEL SYSTEM, GASOLINE. Fuel Tank Before replacing this part due to Hard to Fill condition, check the Fuel Filler Tube for restriction after the second door of the capless unit. Replace the Fuel Filler Tube if the second door of the capless unit does not open properly. Contact Sylvia Lopez at (248) 520-9734 if a Tank needs to be replaced.
90034132018-06-04. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
90031092018-06-04. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER. Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
90037182018-06-04. Service bulletin. EQUIPMENT:ELECTRICAL. Rear View Camera In the case for inoperative camera, radio screen is blue or black in reverse mode. Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am- 4pm. If you do not get a response within 15 minutes continue with the repair. Make sure that connector is inserted properly. If there is a need to replace camera. In case of bad wire harness. Replace the harness and have it sent back to QEC.
90035302018-06-04. Service bulletin. SERVICE BRAKES. Brake Pedal Sensor For vehicles with DTC's P0572 or C0042, or complaints of brake lights staying on or cruise control not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.
90036242018-06-04. Service bulletin. LANE DEPARTURE: BLIND SPOT DETECTION. Blind Spot Detection Sensor If you are replacing this part due to a customer complaint of "Blind spot alert unavailable - wipe rear bumper", please read the following instructions before proceeding. 1) Verify that the rear bumper is clear of any obstructions. The process to clear the blockage message involves first cycling the ignition. 2) The vehicle must be driven on the road and pass/be passed by vehicles on both the left and right sides. After completing those steps, the blockage message will clear and the system will function as designed. Please call Zaid Almasarweh (586) 258-6771 if the previous steps do not correct the problem. If there is no response within 15 minutes, please continue with your normal diagnostic process.
90025192018-02-21. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. 82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
18-049-16 REV. B2017-11-03. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.
08-089-162017-11-03. Service bulletin. LANE DEPARTURE: BLIND SPOT DETECTION. Flash: Blind Spot Monitor System Improvements This bulletin involves updating the Left and Right Blind Spot Sensor (LBSS/RBSS) software. The customer may experience the blind spot monitor indicator may not chime alerting them that there is an object next to the vehicle.
18-024-17 REV. C2017-11-03. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P0556 - Brake Booster Pressure Sensor Circuit Performance. P040B - Exhaust Gas Recirculation Temperature Sensor 1 Circuit Performance(3.6L Only). U1424 - Implausible Engine Torque Signal Received(2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open(3.6L Only). P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation(3.0L and 3.6L Only). The following DTCs have been changed from a one trip fault to a two trip fault for(3.0L and 3.6L Only):P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 1. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0394 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 2. In addition, customers may experience one of the following conditions:A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light(3.6L Only). Other enhancements included in this update:Improvements to vehicle drivability during a cam or crank sensor MIL condition(2017 MY Only). Improved knock sensor performance.
08-028-17 REV. B2017-11-03. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. RA3 and RA4 Radio Over The Air Software Updates This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.