WenmarOpen by Wenmar Pro

Service bulletins for the 2011 Dodge Durango

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

156 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
9003357A2024-01-02. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a2023-04-17. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
90033572023-04-17. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
09002142023-01-17. Service bulletin. ENGINE AND ENGINE COOLING. MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension)
S22090000042022-12-19. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
90028872022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
S1709000010RevB2022-09-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR; UNKNOWN OR OTHER. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S1709000010 Rev.2022-07-18. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S1709000010 RevB2022-05-31. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
21-004-132021-03-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); ENGINE AND ENGINE COOLING. Flash: Drivetrain Control Module (DCTM) - Transfer Case Operational Enhancements This bulletin involves flashing the Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms: Moaning or groaning noise while coasting and/or during a very light acceleration around 5 to 8 mph (8 to 13 kph). The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD. Binding of the front driveline while turning on steep grades at speeds around 3 to 5 mph (5 to 8 kph).Surge/Shudder at speeds greater than 50 mph (80 kph).
S1709000010 Rev.2021-02-16. Service bulletin. ENGINE AND ENGINE COOLING. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S20080001132020-09-28. Service bulletin. ENGINE; ELECTRICAL SYSTEM. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle
90040762019-07-15. Service bulletin. EQUIPMENT; ENGINE. Oil Filter Adapter If replacing Oil Filter Adapter due to oil leak, please be aware a seal kit is available for repair. If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.
07-002-152018-11-19. Service bulletin. ENGINE. Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
07-002-15 REV. A2018-09-24. Service bulletin. ENGINE. Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
90036942018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
09-002-14 REV. B2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
09-002-14 REV. A2018-06-11. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire
09-002-142018-06-11. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire
N08020720132018-06-04. Service bulletin. EQUIPMENT; ENGINE; POWER TRAIN. Advanced Field Action Communication ? N0802072013 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2009 through 2012 model year: (DS) Ram Truck (ND) Dodge Dakota (HB) Dodge Durango (HG) Chrysler Aspen NOTE: All of the above involved vehicles are equipped with a Chrysler 9.25? rear axle (sales code DRB) or C235 rear axle (sales code DRN). The above vehicles may have been built with a rear axle pinion nut that can loosen, which could result in the rear axle locking up. This could cause a loss of vehicle control and/or a crash with little warning. Chrysler will conduct a voluntary safety recall on all affected vehicles to install a rear axle pinion nut retainer. Dealers will be notified of the launch of this safety recall by way of established methods used in the past.
18-014-132018-05-14. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: MIL Illumination P0108- Manifold Absolute Pressure Sensor Circuit High This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P0108- Manifold Absolute Pressure Sensor Circuit High
05048043A$2018-03-13. Service bulletin. ENGINE. PSU Exhaust Phaser 05048043AB If replacing the Exhaust Phaser for the following codes: P0340 Cam Missing/Camshaft Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.
RL108213A$2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
09-002-132016-04-26. Service bulletin. ENGINE. SUMMARY TO BE PROVIDED ON A FUTURE DATE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.