WenmarOpen by Wenmar Pro

Service bulletins for the 2011 Dodge Durango

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

156 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
1012322024-11-07. Service bulletin. POWER TRAIN. Plate - Planetary
V512022-12-19. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); UNKNOWN OR OTHER. Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
90028772022-07-25. Service bulletin. BACK OVER PREVENTION; POWER TRAIN. 52124768A$ - Bearing Assy - Rear For any noise related issue, before replacing this part please review and follow the updated "Hub & Bearing Noise Diagnostic Procedure", found in STAR News #75 and in Service Manual. See DealerCONNECT>TechCONNECT>Service Info>Rear Susp>Hub and Bearing>Diagnosis and Testing>Diagnosis and Testing - Hub and Bearing - Noise.
18-014-132022-07-25. Service bulletin. POWER TRAIN. Flash: MIL Illumination P0108- Manifold Absolute Pressure Sensor Circuit High This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P0108- Manifold Absolute Pressure Sensor Circuit High
N08020720132022-07-25. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. Advanced Field Action Communication ? N0802072013 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2009 through 2012 model year: (DS) Ram Truck (ND) Dodge Dakota (HB) Dodge Durango (HG) Chrysler Aspen NOTE: All of the above involved vehicles are equipped with a Chrysler 9.25? rear axle (sales code DRB) or C235 rear axle (sales code DRN). The above vehicles may have been built with a rear axle pinion nut that can loosen, which could result in the rear axle locking up. This could cause a loss of vehicle control and/or a crash with little warning. Chrysler will conduct a voluntary safety recall on all affected vehicles to install a rear axle pinion nut retainer. Dealers will be notified of the launch of this safety recall by way of established methods used in the past.
08-005-132022-07-25. Service bulletin. BACK OVER PREVENTION; ELECTRICAL SYSTEM; POWER TRAIN. Flash: Power Liftgate May Not Power Open Or Close This bulletin involves reprogramming the Power Liftgate Module with new software. The customer may experience the Power Lift Gate not opening and closing under power. Upon further investigation the Technician may find that B1882 Power Liftgate Position Sensor 1 Circuit set.Updating the software will correct the conditions listed above.
21-003-132022-07-18. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Drivetrain Control Module (DCTM) - Transfer Case Operational Enhancements This bulletin involves flashing the Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:A driveline bump is felt during acceleration at approximately 10 mph (16 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 - 5 mph (5 - 8 kph).
21-004-132022-07-18. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Drivetrain Control Module (DCTM) - Transfer Case Operational Enhancements This bulletin involves flashing the Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:Moaning or groaning noise while coasting and/or during a very light acceleration around 5 to 8 mph (8 to 13 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 to 5 mph (5 to 8 kph).Surge/Shudder at speeds greater than 50 mph (80 kph).
90045092022-05-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:FILTER/SCREEN. Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
S2008000113 Rev.2021-05-24. Service bulletin. POWER TRAIN. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
21-003-132021-03-15. Service bulletin. EQUIPMENT; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); ELECTRICAL SYSTEM. Flash: Drivetrain Control Module (DCTM) - Transfer Case Operational Enhancements This bulletin involves flashing the Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:A driveline bump is felt during acceleration at approximately 10 mph (16 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 - 5 mph (5 - 8 kph).
21-004-132021-03-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); ENGINE AND ENGINE COOLING. Flash: Drivetrain Control Module (DCTM) - Transfer Case Operational Enhancements This bulletin involves flashing the Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms: Moaning or groaning noise while coasting and/or during a very light acceleration around 5 to 8 mph (8 to 13 kph). The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD. Binding of the front driveline while turning on steep grades at speeds around 3 to 5 mph (5 to 8 kph).Surge/Shudder at speeds greater than 50 mph (80 kph).
N08020720132018-06-11. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. Advanced Field Action Communication ? N0802072013 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2009 through 2012 model year: (DS) Ram Truck (ND) Dodge Dakota (HB) Dodge Durango (HG) Chrysler Aspen NOTE: All of the above involved vehicles are equipped with a Chrysler 9.25? rear axle (sales code DRB) or C235 rear axle (sales code DRN). The above vehicles may have been built with a rear axle pinion nut that can loosen, which could result in the rear axle locking up. This could cause a loss of vehicle control and/or a crash with little warning. Chrysler will conduct a voluntary safety recall on all affected vehicles to install a rear axle pinion nut retainer. Dealers will be notified of the launch of this safety recall by way of established methods used in the past.
N08020720132018-06-04. Service bulletin. EQUIPMENT; ENGINE; POWER TRAIN. Advanced Field Action Communication ? N0802072013 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2009 through 2012 model year: (DS) Ram Truck (ND) Dodge Dakota (HB) Dodge Durango (HG) Chrysler Aspen NOTE: All of the above involved vehicles are equipped with a Chrysler 9.25? rear axle (sales code DRB) or C235 rear axle (sales code DRN). The above vehicles may have been built with a rear axle pinion nut that can loosen, which could result in the rear axle locking up. This could cause a loss of vehicle control and/or a crash with little warning. Chrysler will conduct a voluntary safety recall on all affected vehicles to install a rear axle pinion nut retainer. Dealers will be notified of the launch of this safety recall by way of established methods used in the past.
21-003-132018-05-21. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Drivetrain Control Module (DCTM) - Transfer Case Operational Enhancements This bulletin involves flashing the Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:A driveline bump is felt during acceleration at approximately 10 mph (16 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 - 5 mph (5 - 8 kph).
21-004-132018-05-21. Service bulletin. POWER TRAIN:DRIVELINE:DRIVESHAFT. Flash: Drivetrain Control Module (DCTM) - Transfer Case Operational Enhancements This bulletin involves flashing the Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:Moaning or groaning noise while coasting and/or during a very light acceleration around 5 to 8 mph (8 to 13 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 to 5 mph (5 to 8 kph).Surge/Shudder at speeds greater than 50 mph (80 kph).
18-014-132018-05-14. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: MIL Illumination P0108- Manifold Absolute Pressure Sensor Circuit High This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P0108- Manifold Absolute Pressure Sensor Circuit High
18-014-132018-02-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: MIL Illumination P0108- Manifold Absolute Pressure Sensor Circuit High This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P0108- Manifold Absolute Pressure Sensor Circuit High
N08020720132018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. Advanced Field Action Communication ? N0802072013 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2009 through 2012 model year: (DS) Ram Truck (ND) Dodge Dakota (HB) Dodge Durango (HG) Chrysler Aspen NOTE: All of the above involved vehicles are equipped with a Chrysler 9.25? rear axle (sales code DRB) or C235 rear axle (sales code DRN). The above vehicles may have been built with a rear axle pinion nut that can loosen, which could result in the rear axle locking up. This could cause a loss of vehicle control and/or a crash with little warning. Chrysler will conduct a voluntary safety recall on all affected vehicles to install a rear axle pinion nut retainer. Dealers will be notified of the launch of this safety recall by way of established methods used in the past.
90031992017-11-03. Service bulletin. STEERING; POWER TRAIN. Steering Column If vehicle comes in for steering column replacement, verify column installed. Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star. UPDATE: 11/9/2016 If the new bearing does not fit through the double dash, you need to replace the lower double dash panel to the latest level. Please see the updated flowchart in StarParts for the correct replacement panel.
21-004-132016-06-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
21-003-132016-06-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
21-003-132016-06-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. SUMMARY TO BE PROVIDED ON A FUTURE DATE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.