WenmarOpen by Wenmar Pro

Service bulletins for the 2011 Dodge Charger

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

152 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
S17090000102023-01-09. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
V512022-12-19. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); UNKNOWN OR OTHER. Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
90043612022-09-26. Service bulletin. POWER TRAIN. NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
08-040-142022-08-29. Service bulletin. PARKING BRAKE; POWER TRAIN; ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS; ELECTRICAL SYSTEM. Police Vehicle A/C Inoperative This bulletin involves relocating the A/C fuse within the front Power Distribution Center (PDC). Customer comments A/C is warm. On further inspection the technician will notice the A/C clutch fuse is loose in its cavity (#12) in the PDC. This will cause a poor connection and the fuse cavity to be distorted.
1806715REVA2022-08-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: PCM Software Enhancements.
19-003-122022-07-25. Service bulletin. STEERING; POWER TRAIN. Police Vehicle Power Steering Overheat During Closed Course Training Exercises This bulletin involves installing an external power steering cooler on the involved police fleet vehicles. The police fleet may experience increased steering efforts or power steering overheat during extended periods of extreme closed course handling maneuvers while conducting training exercises in ambient temperatures above 100° F (38° C). Diagnostic Trouble Code C2210-00 - ECU over temp may be present.
18085152022-07-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This bulletin involves selectively erasing and reprogramming the Powertrain Control
90045092022-05-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:FILTER/SCREEN. Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
S2008000113 Rev.2021-05-24. Service bulletin. POWER TRAIN. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
90043612021-04-26. Service bulletin. POWER TRAIN. NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
18-067-15 REV A2019-05-20. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: PCM Software Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the Powertrain Control Module (PCM): ? U0140 - Lost Communication With Body Control Module. ? U0401 - Implausible Data Received From ECM/PCM. ? P0441 - Evap Purge System Performance. ? P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. This software update also has improvements for fuel pump relay cycling during remote starts.
18-085-152019-05-20. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN. Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may describe hearing the fuel pump relay cycling during remote start or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM: ? U0140 - Lost Communication With Body Control Module (BCM). ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. ? P0522 - Engine Oil Pressure Sensor Circuit Low. ? P0108 - Manifold Absolute Pressure Sensor Circuit High. ? P1239 - Engine Oil Temperature Too Low. ? P0298 - Engine Oil Temperature Too High.
23-007-132018-06-04. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL); EQUIPMENT. Mopar '11 Shifter Handle Contacting Bezel This bulletin involves shimming the rear of the shifter to eliminate contact with the shifter bezel and if necessary replacing the shifter bezel if damage has occurred. The customer may experience the shifter contacting the shifter bezel when the shifter is placed into drive.
18-031-12 REV. A2018-05-14. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ELECTRICAL SYSTEM:SOFTWARE. Flash: MIL Illumination P0108 - Manifold Absolute Pressure Sensor Circuit High This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that P0108 - Manifold Absolute Pressure Sensor Circuit High has been set active or stored.Updating the software will correct the condition listed above.
18-031-12 REV. A2018-02-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: MIL Illumination P0108 - Manifold Absolute Pressure Sensor Circuit High This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that P0108 - Manifold Absolute Pressure Sensor Circuit High has been set active or stored.Updating the software will correct the condition listed above.
19-003-122018-02-21. Service bulletin. STEERING; POWER TRAIN. Police Vehicle Power Steering Overheat During Closed Course Training Exercises This bulletin involves installing an external power steering cooler on the involved police fleet vehicles. The police fleet may experience increased steering efforts or power steering overheat during extended periods of extreme closed course handling maneuvers while conducting training exercises in ambient temperatures above 100° F (38° C). Diagnostic Trouble Code C2210-00 - ECU over temp may be present.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.