Service bulletins for the 2013 Chevrolet Volt
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1953 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| PIT5443 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication advises the technician of a concern where the Onstar® menu is missing from the radio display. Pressing the white Onstar® push to talk button and say hide Onstar® menu will hide the menu and saying unhide menu will make the menu come back again. |
|---|---|
| PIC5491G | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. |
| PIT5442 | 2017-08-15. Service bulletin. POWER TRAIN; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center. |
| PIC6089A | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician about vehicles that may have a Battery Saver Message or red Battery Indicator displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code P0AF8 set in history. Technician will need to the 12 volt battery using the GR8 Battery tester. The technician will need to perform the Direct current Power Conversion Test published in Global Service Information to check for maximum current and voltage output. This test requires the use of a Carbon Pyle load tester. In addition, the technician can select the 14 Volt Power Module Control Function in the Engine Control Module and Accessory Power Module Setpoint in the Body Control Module by using the Scan Tool in order to check that the system is able to respond to current loads. If the test fails, if there were low voltage Diagnostic Trouble Codes or P0AF8 was set, the technician should confirm that the 200 amp fuse located in the X50D Fuse Block is torqued to correct specification. Technician should check the voltage on both sides of the 200 amp Fuse while there is a load applied and comparing the voltage readings. Voltage drop can be checked from the positive battery post to the Accessory Power Module side of the 200 amp fuse as well. If the Accessory Power Module will output current under a load but the voltage is low on both sides of the fuse when compared to the voltage output at the Accessory Power Module, check the following Service Information for any other Diagnostic Trouble Codes that may have led to the low voltage condition, Accessory Power Module output terminal is clean and torqued to specification, The Accessory Power Module output cable ring terminal is properly seated to the Accessory Power Module output terminal post and its condition, and test the voltage drop on the ground cables to the engine block, transmission, body and chassis to ensure they are within specification. |
| PIC5322D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician of a customer concern where the heated seat indicator light is not functioning or the heated seats are not up to operating temperature during a remote vehicle start event. This is normal operation of the heated seat during a remote vehicle start event. The electronic climate control module is not in a complete wake up state during a remote vehicle start mode and will not enable the light emitting diode. After a cold soak below 32 degrees Fahrenheit the seat will not get hot in the 10 minutes or less of the remote vehicle start mode. This is due to the fact that the heat element is not in direct contract with the seat surface while the seat is unoccupied and the foam below the heater is full cold insulating air which takes time to heat up. Technician is to communicate to the customer this condition is a normal operating characteristic of their vehicle. It will not impact the designed performance or reliability of the vehicle. Please share this information with the customer, including a copy of this message. |
| PIC6097 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician for balancing a hybrid battery pack after replacing a battery section. Certain unlisted codes may be experienced when using the battery service tool EL50332. If the codes are experienced check the following before calling Midtronic. Please make sure the USB memory stick is fully inserted into the machine. Make sure to follow the on screen instructions do not hook the machine to the battery section until instructed to do so. The balance machine should be on the latest software version available by following the latest version of preliminary information number PI1125. |
| PIC5602B | 2017-08-15. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician to aid in diagnosing a concern of one or all of the following concerns. The customer may state that the reverse lamps are inoperative, the review back up camera is inoperative, and the dome lights are inoperative. Technician may find diagnostic trouble code B2615 set in the Body Control Module. Upon inspection it might be found that the F7DR 7.5 amp fuse is open in the right instrument panel fuse box. After initial inspection a concern can?t be found inspect circuit 6815 going to the drivers and passengers sun visor. It might be required to lower the front part of the headliner to perform the inspection. If a wiring concern is not found move each sun visor up and down and front to back to see if the fuse opens. If the fuse opens replace the sun visor that was being moved when the fuse opened. |
| PIT5076E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again. |
| PIC5380H | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication advises the technician that the Hybrid Powertrain Control Module 2 has been removed from parts restriction. |
| PIC6092 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This Preliminary Information communication advises the technician to not replace any parts for the XM weather, fuel, or movies tabs not working or no information coming up on the display. Apologize to the customer for the inconvenience and let them know that General Motors is working on a solution for this concern. |
| PIP5081G | 2017-08-15. Service bulletin. EQUIPMENT. This Preliminary Information communication provides information to the technician about vehicles that may have whistle, scrape or whine type noise while driving that may be more noticeable during regenerative braking. Technician may find this noise emanating from the left side of the drive unit. The tech may also state that the vehicle has a current or history diagnostic trouble code P0A46. The noise may be caused by the drive motor rotor bearing cage separated. Technician should replace the bearing with the new updated part number. |
| PIC5701B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician about the removal of the high voltage battery pack. Technician will need to disable high voltage and fully drain battery coolant before removing the electrical connections. After following the published high voltage disable procedure and properly draining the coolant from the battery cooling system, it may be helpful to use electrical tape to help seal the connections on the battery relay junction block. If coolant does enter these connectors, clean completely with electrical contact cleaner and low pressure compressed air, then apply a light coating of dielectric grease. |
| PIC5412C | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles that may have a high-pitched whine noise during braking or accelerating. Technician will need to inspect the load floor, in the rear of the vehicle, for being properly secured. If the load floor is not fully seated check the cargo tray under the floor and insure everything is stowed in its own spot. An improperly stowed 120v charge cord set, cargo in the lower tray that can pop the load floor up, and damage to the load floor that causes the floor not to clip into place. |
| PIC6087 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about Apple devices is inoperative or freezing when using the device via USB cable after an IOS8.x.x update. Technician will need to delete the radio from the phone and the phone from the radio. Also close out all apps on the device if it is an iPhone. |
| PIT5399 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable. |
| PIP5081F | 2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that may have whistle, scrape or whine type noise while driving that may be more noticeable during regenerative braking. Technician may find this noise emanating from the left side of the drive unit. The tech may also state that the vehicle has a current or history diagnostic trouble code P0A46. The noise may be caused by the drive motor rotor bearing cage separated. Technician should replace the bearing with the new updated part number. |
| PIC4310L | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system. |
| PIC6039A | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about the main power feed going to the following fuse blocks may be damaged or have poor terminal retention. Technician may comment that they cannot locate the terminals for the following fuse blocks to perform service repair. Technician will need to replace the body harness for this concern. |
| PIP5282 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down. |
| PIC6070A | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-49903 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter. |
| PIP5155A | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have Service Vehicle Soon Lamp (SVS) or Check Engine Lamp (CEL) is on after charging using a 240V charging station. Technician may find a Diagnostic Trouble Code P1EE6 stored current or history. When published Service Information diagnostics do not lead to repair the Hybrid Powertrain Control Module 2 will need to be reprogrammed using Service Programming System. |
| PIC5436C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician some vehicles may have a Service Stabilitrak message and a red brake lamp illuminated on the Instrument Panel Cluster. Technician may find a Diagnostic Trouble Code C0196 in the Electronic Brake Control Module. This concern may be preset after the vehicle was flat towed or just came off a car carrier. Technician will need to perform a Multi Axis sensor learn and a Diagnostic Trouble Code clear in the Electronic Brake Control Module. Then shut ignition off, open and close driver door and let vehicle sit for 3 minutes. After the vehicle has slept for 3 minutes start the vehicle and let it run in park for 10 seconds. Now the vehicle will need to be driven for 30 seconds over 20 miles per hour. If code is cleared and doesn't reset, release the vehicle to the customer. If code resets follow normal diagnosis in Service Information. |
| PIC5442B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician about vehicles equipped with absorbent glass mat 12 volt battery. Technician should insure that the EL-50313 Midtronics GR8 battery charger/tester has the current calibrations. When using the battery charger insure that absorbent glass mat and the correct cold cranking amps is selected. |
| PIC6070 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter. |
| PIC5953A | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.