Service bulletins for the 2010 Chevrolet Express
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1554 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| PIP5276E | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on or a low oil pressure indicated after an oil change. Technician may find Diagnostic Trouble Code P0521. Inspect the engine for any oil leaks and repair if need. Technician should change the engine oil and replace the oil filter using a PF48e type filter. |
|---|---|
| PIP5152B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication provides information to the technician on the proper steps for filling the coolant system for vehicles with a diesel engine and rear heater systems. Dealer will need to review and use Service Information procedures for Cooling System Draining and Filling (Vac-N-Fill Diesel) after all cooling system repairs are made. When filling the cooling systems on vehicles that have been up-fitted with rear heaters, such as ambulances or buses, ensure that the rear heater is purged of all air. |
| PIP5016A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. The left and right cylinder head gaskets are not interchangeable and will block oil and coolant passages if installed incorrectly resulting in severe damage to the engine. Technician is not use any power sanding devices, wire brush or wheel as well as any chemical cleaning agents to clean the gasket surface. Leave the gaskets in the package until the surfaces are ready to install them. Do not set the gaskets on workbenches or tool boxes to avoid introduction of foreign debris. The cylinder head surface is not to be machined measure the head for warpage with a straight edge and feeler gauge replacing the head with warpage in excess of .1 millimeter. All M12 head bolts must be replaced however the M8 bolts can be reused. Install 2 head bolts secured at minimal torque to minimize the chance of introducing foreign material. Use a paint pen on the M12 bolts marking the head of each bolt indicating which of the 4 torque steps have been completed to prevent missing a step or doing a step twice. |
| PIP5282 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down. |
| PIP5168D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
| PIP5232C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5007F | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication advises the technician that vehicles with engine Regular Production Option Code LGH or LML may have an Exhaust Fluid Quality Poor message displayed on the Driver Information Center. Technician will need to complete the current Service Information diagnostic for any current Diagnostic Trouble Codes or symptoms found. If an Exhaust Fluid Quality Poor message is displayed with a specific Diagnostic Trouble Code, use that specific Service Information diagnostic, and repair the vehicle as necessary. If the dealer has found an Exhaust Fluid Quality Poor message with no Diagnostic Trouble Code, diagnose the condition using the current Service Information diagnosis for Diagnostic Trouble Code P20EE / P207F (P2BAD for 2012 and newer model years). After making repairs use the Service Information Document titled "Reductant Fluid Quality Test (With or without DTCs)" to evaluate and clear the Exhaust Fluid Quality Poor DIC message. |
| PIP5152C | 2017-08-15. Service bulletin. FUEL SYSTEM, DIESEL: PRE-HEATER; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the proper steps for filling the coolant system for vehicles with a diesel engine and rear heater systems. Dealer will need to review and use Service Information procedures for Cooling System Draining and Filling (Vac-N-Fill Diesel) after all cooling system repairs are made. When filling the cooling systems on vehicles that have been up-fitted with rear heaters, such as ambulances or buses, ensure that the rear heater is purged of all air. |
| PIP5276F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides steps the technician will uses to diagnose and repair vehicles that have low oil pressure after an oil change with the engine Regular Production Option Code L20, L77, L94, L96, L99, L9H, LC8, LC9, LH9, LMF, LMG, LY6, or LZ1. Vehicle may have Service Engine Soon lamp with Diagnostic Trouble Code P0521 or Low Oil Pressure message on the instrument panel. Dealer will need to determine if bulletin 10-06-01-008 was completed. If the bulletin was performed inspect the left rocker cover. Dealer will insure the left rocker can hold water without leaking. If leaks are found apply room temperature vulcanization silicone to the rocker cover if possible or replace the left rocker cover. |
| 11-00-90-001A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils. |
| 00-06-01-026G | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. |
| 15-00-90-001 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides technicians with diagnostic tips for preventing oil leaks after changing oil and filter. |
| 07-06-04-019E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set. |
| 15-00-89-004A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. |
| 00-06-01-026F | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. |
| 02-06-01-027C | 2017-08-15. Service bulletin. ENGINE. This informational bulletin provides technicians with information to help educate them on the many various combinations of engines, interfacing equipment and vehicle usage which may cause higher than expected oil consumption. |
| 12-06-04-002D | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This informational bulletin provides information to technicians on exhaust fluid range, exhaust fluid quality poor, service exhaust fluid system or Service Emission System Driver Information Center (DIC) messages. |
| 06-00-89-026L | 2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. |
| 06-06-01-010B | 2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; ENGINE AND ENGINE COOLING. This informational bulletin provides information on close-coupled converter and engine replacement. |
| PIP5029H | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years. |
| PIP3119N | 2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; POWER TRAIN. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. |
| PIP5151 | 2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. Technician should use Published Service Information for fuel system cleaning. |
| PIP5152 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL. This Preliminary Information communication provides information to the technician on the proper steps for filling the coolant system for vehicles with a diesel engine and rear heater systems. Dealer will need to review and use Service Information procedures for Cooling System Draining and Filling (Vac-N-Fill Diesel) after all cooling system repairs are made. When filling the cooling systems on vehicles that have been up-fitted with rear heaters, such as ambulances or buses, ensure that the rear heater is purged of all air. |
| PIP4864M | 2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have "Exhaust Fluid Low", "Exhaust Fluid Empty - Refill Now", "Exhaust Fluid Range: XXX" or "Service Exhaust Fluid - See Owners Now" on the Driver Information Center. If the technician is working on 2010 and 2011 model years campaign 11001 has now been released. Other vehicles technician will need to check the Body Control Module and the scan tool to insure the latest calibration are installed in both. Then use the scan tool to check Reductant System Data in the Engine Control Module. Ensure that all three diesel exhaust fluid level sensors are active with the diesel exhaust fluid tank level showing 100%. If the tank level is below 100% add up to 2 gallons of diesel exhaust fluid. After adding the fluid, use a scan tool to reset the reductant fluid tank level. When the reductant level warning shows "none" the diesel exhaust fluid system reset and reprogram is complete. |
| PIP5007C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE; ELECTRICAL SYSTEM. This Preliminary Information communication advises the technician that vehicles with engine Regular Production Option Code LGH or LML may have an Exhaust Fluid Quality Poor message displayed on the Driver Information Center. Technician will need to complete the current Service Information diagnostic for any current Diagnostic Trouble Codes or symptoms found. If an Exhaust Fluid Quality Poor message is displayed with a specific Diagnostic Trouble Code, use that specific Service Information diagnostic, and repair the vehicle as necessary. If the dealer has found an Exhaust Fluid Quality Poor message with no Diagnostic Trouble Code, diagnose the condition using the current Service Information diagnosis for Diagnostic Trouble Code P20EE / P207F (P2BAD for 2012 and newer model years). After making repairs use the Service Information Document titled "Reductant Fluid Quality Test (With or without Diagnostic Trouble Codes)" to evaluate and clear the Exhaust Fluid Quality Poor Driver Information Center message. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.