WenmarOpen by Wenmar Pro

Service bulletin PIP5016A

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10114527
Published by NHTSA2017-08-15
Manufacturer's numberPIP5016A
Manufacturer's date2015-05-08
NHTSA componentENGINE AND ENGINE COOLING:ENGINE:DIESEL

NHTSA's summary

This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. The left and right cylinder head gaskets are not interchangeable and will block oil and coolant passages if installed incorrectly resulting in severe damage to the engine. Technician is not use any power sanding devices, wire brush or wheel as well as any chemical cleaning agents to clean the gasket surface. Leave the gaskets in the package until the surfaces are ready to install them. Do not set the gaskets on workbenches or tool boxes to avoid introduction of foreign debris. The cylinder head surface is not to be machined measure the head for warpage with a straight edge and feeler gauge replacing the head with warpage in excess of .1 millimeter. All M12 head bolts must be replaced however the M8 bolts can be reused. Install 2 head bolts secured at minimal torque to minimize the chance of introducing foreign material. Use a paint pen on the M12 bolts marking the head of each bolt indicating which of the 4 torque steps have been completed to prevent missing a step or doing a step twice.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine

Vehicles listed
CHEVROLET EXPRESS2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
CHEVROLET SILVERADO 15002006, 2007, 2008, 2009, 2010, 2011 (the catalog's model; the bulletin names a series or trim of it)
CHEVROLET SILVERADO 15002014 (the catalog's model; the bulletin names a series or trim of it)
CHEVROLET SILVERADO 1500 HD2002, 2003, 2004, 2005 (the catalog's model; the bulletin names a series or trim of it)
CHEVROLET SILVERADO 25002001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 (the catalog's model; the bulletin names a series or trim of it)
CHEVROLET SILVERADO 35002001 (the catalog's model; the bulletin names a series or trim of it)
CHEVROLET SILVERADO 35002013 (the catalog's model; the bulletin names a series or trim of it)
GMC G SERIES2003
GMC G VAN BUS2004 to 2006
GMC GM2001 to 2002
GMC SAVANA2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
GMC SIERRA 15002014 (the catalog's model; the bulletin names a series or trim of it)
GMC SIERRA 25002004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 (the catalog's model; the bulletin names a series or trim of it)
GMC SIERRA DENALI2007, 2008, 2009, 2010, 2011, 2012, 2013 (the catalog's model; the bulletin names a series or trim of it)
GMC SIERRA DENALI2015 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20145772014-12-18. Engine
20140052014-01-13. Engine
14V0070002014-01-13. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM
20073632007-11-09. Engine
07V5210002007-11-07. ENGINE AND ENGINE COOLING
06V2890002006-08-03. ENGINE AND ENGINE COOLING

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
00-06-01-026R2025-12-03. Service bulletin. This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
23-NA-1532025-10-25. Service bulletin. The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
22-NA-0802025-10-16. Service bulletin. This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder.
15-NA-0102025-07-07. Service bulletin. This service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
25-NA-0522025-04-28. Service bulletin. This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
25-NA-0522025-04-10. Service bulletin. This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
22-NA-0742025-02-12. Service bulletin. This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
21-NA-0432025-02-12. Service bulletin. This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
20-NA-1662025-01-23. Service bulletin. This service bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.
09-06-04-026Z2025-01-23. Service bulletin. This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.