Service bulletins for the 2016 Chevrolet Camaro
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1709 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| PIP5330B | 2017-10-04. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on. |
|---|---|
| PIP5498A | 2017-10-04. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair. |
| PIP5216F | 2017-10-04. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIE0350B | 2017-08-31. Service bulletin. ENGINE AND ENGINE COOLING. This engineering informational bulletin is requesting information from the field on vehicles that have a concern on Bang or Loud Noise with No Forward (Drive) or Reverse Ranges |
| PIP5395B | 2017-08-31. Service bulletin. ENGINE. This Preliminary Information communication advises the technician on the steps to diagnose the concern and the steps to repair the concern. Customer hears a rattle or ticking noise that is louder inside the vehicle than outside. A-This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced. |
| PIE0369B | 2017-08-31. Service bulletin. ENGINE. This engineering informational bulletin is requesting information from the field of vehicles with the condition of a SES light on with one or more DTC's set. |
| 17-NA-039 | 2017-08-31. Service bulletin. ENGINE. This informational bulletin provides additional information on what oil to use in the 2.0L engines to eliminate the risk of engine/piston failure. |
| 17-NA-033 | 2017-08-31. Service bulletin. ENGINE. This technical bulletin provides a procedure to locate at repair the engine wiring harness contacting the drive belt and relocate the harness away from the belt. |
| 16-NA-173 | 2017-08-31. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Technical Bulletin provides a procedure to bond the ceramic pins to the exhaust valves to correct a condition of a rattle noise from the rear of the vehicle. |
| 07-06-04-025L | 2017-08-31. Service bulletin. ENGINE. This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic. |
| PIP5232B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5216B | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIP5216A | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIC6160 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. This Preliminary Information communication provides information to the technician with the step to diagnose and repair vehicle that may have an engine cooling fan that is inoperative with Diagnostic Trouble Code P0480 of P0691. Dealer will need to inspect forward lamp harness water intrusion and replace the damaged harness and components. |
| PIC6155 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have noise or disturbance inside the vehicle at low engine speeds, typically 900 - 1100 RPM. Technician will need to contact General Motors Technical Assistance Center for further assistance. |
| PIT4943D | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIP5179B | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT:MECHANICAL; FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines. |
| PIP5163B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIP5313 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication advises the technician that the E80 Engine Control Module part numbers 12655021, 12668437, and 12672502 has been placed on restriction through General Motors Technical Assistance Center to assist GM Engineering with product feedback. Dealer will need to contact General Motors Technical Assistance Center for further assistance. |
| PIP5179A | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines. |
| 09-06-04-026M | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2. |
| 16-NA-173 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This technical bulletin provides a procedure to bond the ceramic pin to the exhaust valve to correct a customer concern on an exhaust rattle originating from the rear of the vehicle caused by to the ceramic pin being loose on the exhaust valve. |
| 17-NA-109 | 2017-08-15. Service bulletin. ENGINE. This technical bulletin provides a procedure to locate and repair the engine wiring harness if found chaffing against the water outlet bolt boss. |
| 16-NA-129 | 2017-08-15. Service bulletin. SUSPENSION; ENGINE; EQUIPMENT. This informational bulletin advises the technician not to change the crankshaft balancer if it has the illusion of a wobble or vibration appearance. |
| PIP5331B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that some vehicles may have rattle, tick, or knock type noise. If there are any drivability concerns they should be addressed prior to the following diagnostic progression. Technician will take a sound file or video with sound of the noise prior to dis-assembly. Technician may find this noise hard to isolate to one area in the engine. There are four different steps to take to diagnosis the concern. Technician will perform injector diagnosis to ensure there are no leaking injectors causing a noise due to excessive fuel in any one cylinder. Replace any out of specification injectors the reevaluate for the noise. Technician will remove the intake manifold and visually inspect for excessive carbon on the intake valve stems and top of the valve causing noise. If carbon is present then follow the latest version of PIP5029 to clean the valves or replace heads as needed. Technician will remove the cam cover of the affected bank (both if needed) to inspect for soft or spongy stationary hydraulic lash adjusters. Push down on the rocker end at the stationary hydraulic lash adjusters to test for soft or spongy. If soft or spongy stationary hydraulic lash adjusters are found, carefully remove the affected head and inspect the oil passage below the head gasket for debris. If debris is found, inspect the camshaft caps for wear or discoloration due to lack of oil. During inspection if wear or discoloration is found then replace the cylinder head assembly with camshafts. If there is no wear or discoloration, clean the oil passages and replace the head gasket. Technician will use chassis ears or a stethoscope; listen to the right and left side of the engine. Once the noise is isolated or if unable to isolate, remove the piston and rod assemblies from the affected bank(s) to inspect for either; a loose rod bushing in the rod, or a loose wrist pin in the bushing. If this is found, replacing the piston an |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.