Service bulletins for the 2014 Chevrolet Camaro
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1838 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| PIC6077C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that may have a radio that the iPhone does not automatically re-pair and is no longer shown in the radio?s Device List, XM Weather Alerts Activate Automatically after an ignition cycle, the Bluetooth connection may be lost when replying to a text message, After a OnStar Turn By Turn a "Routing" screen appears and stays on display even though the route requested had finished downloading, and USB audio still plays through speakers while Bluetooth phone call is in session. Technician will need to reprogram the radio. |
|---|---|
| PIP5318 | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that have a misfire event that usually occur at speeds of 70 miles per hour, 3rd Gear, and 3500 ? 4500 revolutions per minute. Dealer should advise customer to refer to TopTierFuel.com for availability in their respective area and fill with 91 or higher octane level fuel. |
| PIC6120 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about iPhones will not always autoconnect through Bluetooth to the vehicle. If the vehicle has more than one device listed in the Bluetooth device list, and the last device used was an Apple product, the Apple products will not autoconnect. The system will connect to one of the other devices instead. This concern is usually noticed after Retained Accessory Power has cancelled and the vehicle has gone to sleep. Advise the customer that they will need to update their Apple device to the latest operating system. |
| PIC6116 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about some vehicles that may have a concern of Bluetooth music skipping. This condition is a normal operating characteristic of the vehicle. Streaming music through Bluetooth uses a lot of the radio's processing resources. If the radio is also dedicating a large amount of resources to other applications such as navigation, booting, or XM Weather the Bluetooth audio may hesitate/skip as the system is being heavily loaded. |
| PIC6106A | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that may have the radio display that will go blank and come back on after a few seconds then display may show the splash screen or come back on to the last screen that was displayed. Infrequent resets can occur in a high load condition such as long routes, driving against a route or rerouting, Bluetooth streaming, and start up when Bluetooth or USB is syncing is considered a normal operating condition. Replacing the radio for these infrequent instances will not repair these concerns. If published Service Information diagnostics do not lead to a diagnosis and the concern is happening on more than just the very rare occasions, retrieve the radio end model part number using Global Diagnostic System 2 or from the radio and contact the General Motors Technical Assistance Center for further diagnostic assistance. |
| PIT5236F | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance. |
| PIT5236E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process. |
| PIC5932A | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center. |
| PIT5444 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the ?i? icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work. |
| PIC4788F | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician of diagnostic instructions to take when the key will not fold into the fob or will not stay in the folded position. The technician may comment that the key in the fob will not fold close or stay latched closed. Damage to the folding mechanism could result from storing the key in the door lock cylinder and accidently bumping or making contact with the key fob. Please advise all dealer personnel to refrain from storing the key in the door lock even for brief periods. |
| PIT5443 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication advises the technician of a concern where the Onstar® menu is missing from the radio display. Pressing the white Onstar® push to talk button and say hide Onstar® menu will hide the menu and saying unhide menu will make the menu come back again. |
| PIP4786B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure message. Technician may also find a Diagnostic Trouble Code P0521 in the Engine Control Module. Technician should follow all published Service Information diagnosis. When using a scan tool if the oil pressure is low but the oil pressure at the oil filter housing is correct, technician should inspect the Valve Lifter Oil Filter for debris/sludge that could be restricting oil flow to the oil pressure sensor. Technician should remove the Valve Lifter Oil Filter and clean it. If the Valve Lifter Oil Filter cannot be cleaned replace it. |
| PIC5491G | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. |
| PIT5442 | 2017-08-15. Service bulletin. POWER TRAIN; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center. |
| PIC5322D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician of a customer concern where the heated seat indicator light is not functioning or the heated seats are not up to operating temperature during a remote vehicle start event. This is normal operation of the heated seat during a remote vehicle start event. The electronic climate control module is not in a complete wake up state during a remote vehicle start mode and will not enable the light emitting diode. After a cold soak below 32 degrees Fahrenheit the seat will not get hot in the 10 minutes or less of the remote vehicle start mode. This is due to the fact that the heat element is not in direct contract with the seat surface while the seat is unoccupied and the foam below the heater is full cold insulating air which takes time to heat up. Technician is to communicate to the customer this condition is a normal operating characteristic of their vehicle. It will not impact the designed performance or reliability of the vehicle. Please share this information with the customer, including a copy of this message. |
| PIC5965C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician for a concern with the blower motor and or indicators are inoperative, the blower motor may be blowing but the speed can?t be adjusted, or the air conditioning is not blowing cold enough. Upon inspection there might be a diagnostic trouble code U1510 set in the Electronic Climate Control module. If the concern is duplicated technician will reprogram the Electronic Climate Control module with the latest calibrations. |
| PIC5983F | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication advises the technician that the following part numbers for the 2014 or 2015 Camaro with Regular Production Option Code Z28 are restricted 22958646, 22958647, 22958658, 22958607, 22958637, 22958634, 22903660, 22903659, 23179350, 23179351, 23487228, 22968220, 23468210, 22954889, 22873225, 22873227, 23240634, 23240635, 23240650, 23240651, 22908036, 22908498, 22894294, 22894302, 23473010, 23473011, 23468208, 22925211, 22972716, 22972708, 23164563, 12653293, 12653294, 22997723, 22985096, 22968219, 22966600, 23468209, and 23473511. Technician will need to contact General Motors Product Quality Center with the warranty repair order number or the customer pay parts ticket number, along with the vehicle identification number, customer?s last name and the General Motors Technical Assistance Center or District Manager of Aftersales approval. |
| PIP5097A | 2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides the technician with the following steps to correct a moan noise from the rear axle during cold turning maneuvers. This noise might start to be noticed as the vehicle accumulates over 3000 miles. The technician is to perform the following steps. 1. With original lube in axle, conduct Freeway Speeds for 10 miles to warm up lube. 2. Immediately drain original lube and refill with fresh lube. 3. In parking lot lock steering to the right, and then execute 5 Full Circles at (5-10 mph). 4. . In parking lot lock steering to the left, and then execute 5 Full Circles at (5-10 mph). 5. Perform 4 Figure 8?s at (5-10 mph). 6. Freeway Speeds for 20 miles until operating temperature is achieved. 7. In parking lot lock steering to the right, and then execute 5 Full Circles at (5-10 mph). 8. In parking lot lock steering to the left, and then execute 5 Full Circles at (5-10 mph). 9. Perform 4 Figure 8?s at (5-10 mph). 10. Immediately drain current lube in axle and refill with fresh lube. 11. Perform Steps 3 thru 9 again. 12. Immediately drain current lube in axle and refill with fresh lube. Proceed with steps 2 through 9 two times, for a total of 3 drain and fill procedures. This should only be done for a moan noise from the rear axle during cold start turning maneuvers. During regular maintenance the fluid only needs to be changed one time. |
| PIP4959E | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required. |
| PIP5209C | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication advises the technician to follow this Preliminary Information if there is a diagnostic trouble code P00C6 and or P228C set and normal Service Information diagnostics didn?t lead to a repair. Technician is to recheck the terminals at the Engine Control module for fit and tension as well as the crimp to the wire. The engine control module terminals to inspect are in the X2 connector. Inspect terminal number 3, 18 and 19 for the fuel rail pressure sensor and in the X3 connector terminals 16 and 32 for the high pressure fuel pump. The diagnostic trouble codes could set with as little as a 2 ohm resistance reading on these circuits. If any concerns are found replace the affected terminals and verify the repair. |
| PIT5076E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again. |
| PIC5839C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. |
| PIC6087 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about Apple devices is inoperative or freezing when using the device via USB cable after an IOS8.x.x update. Technician will need to delete the radio from the phone and the phone from the radio. Also close out all apps on the device if it is an iPhone. |
| PIC5956A | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:WIRING. This Preliminary Information communication advises the technician about the operation of the Daytime Running Lamp that will turn off when the turn signal is turned on. This is the normal operation of this lighting system, and no repairs should be made to try to repair this. |
| PIT5399 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.