WenmarOpen by Wenmar Pro

Service bulletins for the 2017 BMW X5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

300 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B6524162018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). "NBT NAVIGATION DOES NOT ROUTE ON TOLL ROADS. NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes ""without a cash option"" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes ""without cash option"". UPDATE Install new map data."
B6523162018-11-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. ?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
B3405162018-11-05. Service bulletin. SERVICE BRAKES. CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
B1223162018-11-05. Service bulletin. POWER TRAIN. SHUDDER OR JERKING IN 7TH AND 8TH GEARS AT 1000 - 1400 RPM. A shudder or slight jerking can be felt when driving with the transmission in 7th or 8th gear and the engine speed is between 1,000 and 1,400 RPM. No related faults are stored and there are not any problems in the chassis systems or with the wheels and tires. This shudder or jerking could begin due to the characteristic power pulses of the N63T engine when it is in VVT mode at low engine loads.
B6412162018-11-05. Service bulletin. EQUIPMENT. "HVAC BLOWER NOT WORKING This Service Information bulletin supersedes SI B64 12 16 dated August 2016. HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"
B6119162018-11-05. Service bulletin. ELECTRICAL SYSTEM. SERVICE ENGINE SOON (MIL) - SME FC 21F20D. Malfunction Indicator Lamp (MIL) is illuminated. The following codes may be stored in the fault memory of the battery management electronics (SME). 21F20D - SME, safety concept: Switch-off of switch contactors by safety circuit 21F1F6 - High-voltage battery, switch contactors: Switch-off after a fault Software bug: erroneous fault code stored in SME.
B3101122018-11-05. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. CLICKING NOISE FROM FRONT AXLE This Service Information bulletin supersedes SI 31 01 12 dated June 2015. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
B1803162018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. DDE FAULT CODE: 28DE00 - EXHAUST GAS PRESSURE SENSOR BEFORE TURBINE, PLAUSIBILITY. After performing repairs where the engine harness was disconnected and reconnected at the differential pressure and the exhaust pressure sensor, the following fault is then stored in the DDE: 28DE00 - Exhaust gas pressure sensor before Turbine, plausibility: exhaust gas pressure in front of turbine dynamically not plausible
B1218162018-11-05. Service bulletin. ENGINE. CHECK CONTROL MESSAGE: NO OIL PRESSURE. Check Control message: Oil pressure warning. Stop carefully is displayed. There are no related faults to oil pressure stored in the DDE. Unfavorable DDE software application When operating during automatic engine start-stop function stop, it may be the case that the oil pressure is incorrectly determined to be too low, which triggers a CC message.
B6509152018-11-05. Service bulletin. EQUIPMENT. SI B65 09 15 November 2016 Audio, Navigation, Monitors, Alarms,SRS Technical Service NBT Head Unit High (HU-H) Resets Intermittently or Permanently. The Head Unit-High (HU-H) resets intermittently or permanently. 1. The display is inoperative and there is no audio output 2. Automatic system start-up after a couple of seconds Fault Code E1C440 set No Fault Codes set Software error in the Head Unit High (HU-H)
B6128162018-11-05. Service bulletin. ELECTRICAL SYSTEM. DELIVERY STOP: CHECK THE CHARGING PROCESS OF THE HIGH-VOLTAGE BATTERY.
B6124162018-11-05. Service bulletin. ELECTRICAL SYSTEM. "SME FAULT CODE 21F21F. The fault code (FC) ""21F21F - High-voltage system: Monitoring of insulation resistance deactivated due to fault of the safety box"" is stored in the battery management electronics (SME). The fault does not set any CCM's, is not perceivable to the customer and has no effect on the complete vehicle operation. Safety box malfunction"
B2406162018-11-05. Service bulletin. POWER TRAIN. "FC 44E4D1 stored in Transmission Control Unit, either: 1. When no other fault codes stored. ? Customer has seen no performance issues. OR 2. When any of the following fault codes are stored. 44D141 - transmission monitoring: Clutch A and D implausible 44D0E1 - transmission monitoring: Clutch B implausible 44D191 - transmission monitoring: Clutch C and D implausible 44D151 - transmission monitoring: Clutch A and E implausible 44D0D1 - transmission monitoring: Clutch A implausible 44CFB1 - transmission monitoring: Clutch A, D and E implausible 44CFD1 - transmission monitoring: Fault pattern - gear monitoring implausible And possibly: ? Customer reports harsh shifting ? Check Control message ""Drivetrain malfunction"" Various"
B1227162018-11-05. Service bulletin. ELECTRICAL SYSTEM. "DIAGNOSING NON FUNCTIONING ""eDRIVE"". The customer complains that the vehicle will not go into ""eDrive"", and in some cases ""eDrive"" is greyed-out in the control display (CID) and is not selectable. Also, there are no pertinent electric drivetrain fault codes that assist with diagnosis. Possible 12 volt battery or Intelligent Battery Sensor (IBS) failure."
B6504142018-11-05. Service bulletin. AIR BAGS. "AIRBAG WARNING LIGHT: ACSM FC 930A60 OR 930A1C SEAT OCCUPANCY DETECTION. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Front passenger seat occupancy detection transmitting fault (moisture)"" is stored. The fault may or may not currently be present. The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
B6119152018-11-05. Service bulletin. STEERING. Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.
B5207162018-11-05. Service bulletin. SEATS. LOSS OF SEAT ADJUSTMENT CONTROL. Front seat electric adjustment controls do not function. Electrostatic discharge damage the seat module.
B8402142018-11-05. Service bulletin. EQUIPMENT. ConnectedDrive/BMW Assist System Diagnosis Information This Service Information bulletin replaces SI B84 02 14 dated July 2014 What's New: Model - Removed models which no longer support BMW Assist functionality and added new models. Procedure - Add step requesting print out of ConnectedDrive Service Cockpit page Information - Add SI for ConnectedDrive Service Cockpit; updated the hyperlinks and email address for CD support team; deleted scenario for old CDMA unit which are no longer supported. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
B6402172018-11-05. Service bulletin. EQUIPMENT. NOISE FROM A/C ON POWER-UP AND VENT SELECTION. When selecting a desired outlet vent combination and on power-up (resetting of previous vent selection) of the A/C air distribution system, a disturbing noise is heard (see video - tinyurl.com/y89pdvva). Contact between directional flaps and distributor housing
B6128172018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. "SME FAULT CODE 21F04B. One or several of the following check control messages (CCM) may be displayed: ""Engine fault! Power loss"" (CCM-ID: 29) ""Powertrain malfunction!"" (CCM-ID: 633) ""Hybrid system malfunctioning!"" (CCM-ID: 585) Note: The fault code 21F04B stated below may also be entered without any of the above mentioned CC messages being displayed A timing problem between the SME and the cell supervision circuit (CSC)."
B8403112018-11-05. Service bulletin. EQUIPMENT. "?Telematics Device Spares Replacement Part Activation via DCSnet for BMW Assist What's New: ? Model: All models added along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added "Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."
B6507172018-11-05. Service bulletin. EQUIPMENT. "LIST OF AVAILABLE FM RADIO STATIONS TEMPORARILY NOT AVAILABLE. INFORMATION As of 11/2015, all Entry-NAV/Media head units supplied in new vehicles were upgraded for improved noise characteristics and quality. As a part of this upgrade, the hardware updating the sender lists was changed from an "update after every diversity reception interruption or maximum of four minutes" configuration to "regular interval updates (every four minutes) without regard to diversity reception status" configuration. This may cause a delay of up to four minutes for updates to the sender list when leaving areas of poor reception. The last received transmitter, before the entrance into underground car parking or a tunnel, is still received and will show station identification. This fixed interval update does not apply to Traffic Message Channel updates which remain active. This new equipment operation pattern may be noticed by the customer after replacement of their Head unit. All replacement Head units delivered since 01/2016 have the upgraded design. An immediate solution would be for the customer to select one of their stored favorite stations via the menu or favorites buttons. PARTS INFORMATION Parts exchange or a software update are not effective or approved for this situation. WARRANTY INFORMATION Not applicable."
B6130142018-11-05. Service bulletin. ELECTRICAL SYSTEM. "?BMW Maintenance Program: 12-Volt Battery Replacement Measure What's new: ? "Models" updated: Model Year 2017 vehicles added ? "Models" updated: Model Year G12 (7 Series) excluded from program ? "Procedure" updated: N63R engine added to 2016 Model Year G12 (7 Series) ? Attachment updated with G12 (7 Series) production date range for 2016 Model Year. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is "applicable" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
B6118172018-11-05. Service bulletin. ELECTRICAL SYSTEM. "SME FAULT CODE 21F02A. Upon starting the vehicle, the following CC message is displayed to the customer: "Powertrain malfunction!" (CCM-ID: 633) In addition, one or several of the following CC message(s) may be displayed: "Charging not possible" (CCM-ID: 804), "Hybrid system malfunctioning!" (CCM-ID: 585), "Drive. No restart" (CCM-ID: 586) or "Engine fault! Power loss" (CCM-ID: 29). Possible hardware defect of the safety box."
B6112172018-11-05. Service bulletin. ELECTRICAL SYSTEM. "HV CHARGING INTERMITTENTLY NOT POSSIBLE. HV charging is intermittently not possible. When charging problem occurs, a CCM 804 "Charging Not Possible" will be displayed. Affected vehicles may begin to charge if the charger plug is rapidly plugged/unplugged several times. Charging problem may be noticed consistently at same charging location, but not at others. KLE Software."

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.