Service bulletins for the 2010 BMW X5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
308 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| 240113 | 2018-12-03. Service bulletin. POWER TRAIN. Oil Leak from Transfer Case. Oil is leaking from the transmission area, or oil seepage is noticed from the transmission/transfer case area during a service. CAUSE The leak can be misdiagnosed as a transmission fluid leak from either the mechatronics sleeve or transmission oil pan. The leak is actually coming from the transfer case (input or output shaft seal). |
|---|---|
| 180612 | 2018-12-03. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE. "Voluntary Emissions Recall Campaign 11E-A03: Replace the SCR Mixer. The Selective Catalyst Reduction (SCR) mixer has also been improved to optimize the Diesel Exhaust Fluid (DEF) mixture when introduced into the exhaust system. AFFECTED VEHICLES This Emissions Recall Campaign involves X5d and 335d models that were produced from February 2010 to September 2010. In order to determine whether a specific vehicle has had this Emissions Recall Campaign completed or is affected by this Emissions Recall Campaign, first check if the ""Emissions Recall Campaign Completed"" label SD 92-435 is attached to the right (passenger) rear side of the hood in the engine compartment, close to the windshield. If the label is found, the campaign has already been performed. If the ""Emissions Recall Campaign Completed"" label is not present, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action." |
| 180512 | 2018-12-03. Service bulletin. ENGINE; FUEL SYSTEM, DIESEL. "Voluntary Emissions Recall Campaign 11E-A03: Check and/or Replace Emissions Monitoring Components. 1. Under certain driving conditions, the High-pressure (HP) EGR valve may become restricted with excessive soot. This restriction impedes the emissions performance of the HP EGR valve. This situation may lead to a Service Engine Soon lamp. An optimized EGR valve has been developed to limit this soot buildup. 2. The Selective Catalyst Reduction (SCR) mixer has also been improved to optimize the Diesel Exhaust Fluid (DEF) mixture when introduced into the exhaust system. Note: These Improved parts may have already been replaced during a previous service visit. It will be necessary to inspect these components first before replacement. 3. Reprogramming of the DDE is required to optimize these improved emissions monitoring components. AFFECTED VEHICLES This Emissions Recall Campaign involves X5d (E70) and 335d (E90) models that were produced from April 2009 to March 2011. In order to determine whether a specific vehicle has had this Emissions Recall Campaign completed or is affected by this Emissions Recall Campaign, first check if the ""Emissions Recall Campaign Completed"" label SD 92-435. This label is attached to the right (passenger) rear side of the hood in the engine compartment, close to the windshield. If the label is found, the campaign has already been performed. If the ""Emissions Recall Campaign Completed"" label is not present, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action." |
| 180212 | 2018-12-03. Service bulletin. ENGINE. "?Voluntary Emissions Recall Campaign 11E-A03: Check and/or Replace Emissions Monitoring Components. 1. The Selective Catalyst Reduction (SCR) catalyst has been improved to increase emissions stability over the service life of the vehicle. 2. The SCR mixer has also been improved to optimize the Diesel Exhaust Fluid (DEF) mixture when introduced into the exhaust system. 3. Under certain driving conditions, the High-Pressure (HP) EGR valve may become restricted with excessive soot. This restriction impedes the emissions performance of the HP EGR valve. This situation may lead to the Service Engine Soon lamp illuminating. An optimized EGR valve has been developed to limit this soot buildup. Note: These improved parts may have already been replaced during a previous service visit. It will be necessary to inspect these components first before replacement. 4. Reprogramming of the DDE to optimize these improved emissions monitoring components. AFFECTED VEHICLES This Emissions Recall Campaign involves X5d and 335d models that were produced from January 2008 to September 2009. In order to determine whether a specific vehicle has had this Emissions Recall Campaign completed or is affected by this Emissions Recall Campaign, first check if the ""Emissions Recall Campaign Completed"" label SD 92-435 is attached to the right (passenger) rear side of the hood in the engine compartment, close to the windshield. If the label is found, the campaign has already been performed. If the ""Emissions Recall Campaign Completed"" label is not present, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. If the label is found, the campaign has already been performed. If the ""Emissions Recall Campaign Completed"" label is not present, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or |
| 130712 | 2018-12-03. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation. |
| 121611 | 2018-12-03. Service bulletin. ENGINE; POWER TRAIN. N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode). |
| 121712 | 2018-12-03. Service bulletin. ENGINE; POWER TRAIN. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software |
| B840214 | 2018-12-03. Service bulletin. ELECTRICAL SYSTEM. ?CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause. |
| 541309 | 2018-12-03. Service bulletin. EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; VISIBILITY:SUN/MOON ROOF ASSEMBLY. "?Panoramic Sunroof Repair Instructions. INFORMATION Sunroof Repair Instructions: The panoramic sunroof contains several ""mechanism sets"" which can be repaired and/or replaced independently in the event of a mechanical failure. When performing such a repair to any of these sets, the TIS/ISTA Repair Instructions (REP) should always be consulted. Due to the complex nature of these repairs, a set of complementary instructions with additional detail, explanation, and photos has been developed. The attached Repair Instructions should always be used in conjunction with the TIS/ISTA REP. " |
| 121412 | 2018-12-03. Service bulletin. ENGINE; ELECTRICAL SYSTEM. N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken. |
| B111117 | 2018-12-03. Service bulletin. ENGINE. ?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye. |
| B110815 | 2018-12-03. Service bulletin. ENGINE. N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. * B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair * B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints * B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity * B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. * Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption * Spark plugs fouled with engine oil and excessive engine oil consumption * Excessive engine oil consumption All Vehicles: On vehicles, where an excessive oil consumption between services is the only complaint, a complete oil consumption test as described in SI B11 03 13, must be performed first before replacing the valve seals. On vehicles exhibiting reproducible smoking from the tailpipe when hot, additional engine diagnostic steps (e.g. engine compression test, leak-down tests; inspection of the crankcase ventilation lines and turbo intake/outlet tubes for excessive oil accumulation) should be performed and documented prior to replacement of the valve seals, in order to eliminate other possible causes. Refer to the SIBs listed above for important diagnostic tips. Do not remove the intake manifolds to clean the intake valve carbon. |
| 541309 | 2018-11-26. Service bulletin. VISIBILITY. "Panoramic Sunroof Repair Instructions. INFORMATION Sunroof Repair Instructions: The panoramic sunroof contains several ""mechanism sets"" which can be repaired and/or replaced independently in the event of a mechanical failure. When performing such a repair to any of these sets, the TIS/ISTA Repair Instructions (REP) should always be consulted. Due to the complex nature of these repairs, a set of complementary instructions with additional detail, explanation, and photos has been developed. The attached Repair Instructions should always be used in conjunction with the TIS/ISTA REP. Refer to the following repair attachments: Front Glass Mechanism repair E53, E61, E70, E83, E91.pdf Rear Glass Mechanism repair E53, E61, E70, E83, E91.pdf Wind Deflector Mechanism repair E53, E61, E70, E83, E91.pdf Sunshade Mechanism repair E53, E61, E83.pdf Sunshade Mechanism repair E70, E91.pdf All panoramic roofs for the above-listed models are conceptually similar and utilize similar repairs. NOTE: An E83 (X3) sunroof cassette is used for demonstration of the repairs. Some differences may exist between this and other models. The following prerequisite work is required in order to replace the following kits (in addition to removing the cassette from the car and glass from the cassette): Front Glass Mechanism - None. Rear Glass Mechanism - Remove the front glass mechanism. Wind Deflector Mechanism - Remove the front glass mechanism; remove the rear glass mechanism. Sun shades and Shade Mechanism - None Sunroof Mechanical 3D Animation: A 3D animation has been developed in order to clarify how the sunroof mechanism operates, as well as how it is assembled and disassembled. To view this animation, open Interactive Career Pathways (ICP) and select ""Replace Front and Rear Glass Panel Mechanic"" from the Technical Service Information section of the home page. This animation allows you to: * Operate the mechanism and view from any angle; * Add or remove parts and then cycle the sunroof; * S |
| 520313 | 2018-11-26. Service bulletin. SEATS. Rattle Noise from Rear Seat Backrest. A rattle noise can be heard from the rear seat area when the vehicle is driven. CAUSE The left and right rear seat backrest locks have insufficient lubrication. |
| 340612 | 2018-11-26. Service bulletin. AIR BAGS. DSC Warning Light is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for 'Chassis Control System failure' One or more of the following fault codes are stored: F25, F30 DSC * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV |
| 270212 | 2018-11-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. "The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for ""Chassis Control System failure."" One or more of the following fault codes are stored: DSC: * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV" |
| 130712 | 2018-11-26. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation. |
| B110113 | 2018-11-26. Service bulletin. ENGINE. N63 AND N63T ENGINE: ENGINE OIL CONSUMPTION, ENGINE OIL TOP-UPS AND REFILL CAPACITY. Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently. |
| B011718 | 2018-11-26. Service bulletin. AIR BAGS; ELECTRICAL SYSTEM. For the above-referenced vehicles with passenger?s side airbag modules, BMW of North America, LLC (?BMW NA?) will provide a Customer Support Program as outlined in the Takata Settlement Customer Support Program Overview attachment. This ?component-specific? customer support program applies only if there is a defect in materials or workmanship of the Takata passenger?s side airbag module in a listed vehicle. |
| B011618 | 2018-11-26. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS. For the above-referenced vehicles with driver?s side airbag modules, BMW of North America, LLC (?BMW NA?) will provide a Customer Support Program as outlined in the Takata Settlement Customer Support Program Overview attachment. This ?component-specific? customer support program applies only if there is a defect in materials or workmanship of the Takata driver?s side airbag module in a listed vehicle. |
| 515210 | 2018-11-26. Service bulletin. ELECTRICAL SYSTEM. Various Faults Concerning the Automatic Tailgate Operation. Complaints of sporadic or permanent faults may exist with the automatic tailgate function. One or more of the following fault codes have been stored: A2AB, A2B1, A2B2, A2B3, A2B4, A2B5, A2B6, A2B7, A2B8, A2B9, A2BA, A2BC, A2BE, and A6E2. CAUSE The following four main faults are currently known: 1. The lower tailgate does not close completely. 2. The tailgate wiring harness near the hinge area is damaged. 3. Fault in the left or right side electric spindle drive 4. Fault in the tailgate lock. 5. The tailgate lock and tailgate lift drive connectors may have corrosion or discoloration. If any is seen, the part must be replaced. |
| 513608 | 2018-11-26. Service bulletin. VISIBILITY. "Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""B5116_ECSPPL2.""" |
| 8403014 | 2018-11-26. Service bulletin. ELECTRICAL SYSTEM. iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants |
| 660814 | 2018-11-26. Service bulletin. BACK OVER PREVENTION. Side View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s) |
| 130714 | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. DDE Fault Codes 4882 and 4B82 for EGR Air Mass Plausibility. The Service Engine Soon light is illuminated with one or both of the following fault codes stored in the DDE: 4B82 - Exhaust-gas recirculation-rate control, control deviation 4862 - Air system, air to EGR mass flow, plausibility CAUSE Air mass monitoring of the EGR valve is outside allowable limits. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.