WenmarOpen by Wenmar Pro

Service bulletins for the 2016 BMW i3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

256 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B8406162018-12-03. Service bulletin. ELECTRICAL SYSTEM. ?BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's (Integrated Circuit Card Identifier).
B8402142018-12-03. Service bulletin. ELECTRICAL SYSTEM. ?CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
B6411182018-11-26. Service bulletin. ELECTRICAL SYSTEM; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. STATIONARY CLIMATE CONTROL NOT WORKING AFTER HIGH VOLTAGE CHARGING. After the high voltage (HV) charging procedure, the stationary climate control (aka preconditioning) does not work. This is part of the normal design. There is no fault or defect.
B6110182018-11-26. Service bulletin. ELECTRICAL SYSTEM. THE DISPLAY GOES BLACK, THE ENGINE CAN BE SWITCHED OFF ONLY VIA THE EMERGENCY-OFF.. * On board computer and navigation system goes black or resets. * The engine can only be switched off by pressing the START/STOP button three times (Emergency STOP) * Various Check Control messages are displayed. * At a minimum the following fault code is present: D91C86 - CAN message, status functional safety (ST_FSSY): Timeout-BDC * Additional fault messages may also be displayed Software error in the central gateway of the Body Domain Controller (BDC) control unit. Note: Parts replacement does NOT provide a solution!
B1603182018-11-26. Service bulletin. FUEL SYSTEM, GASOLINE. SERVICE ACTION. REPLACE THE FUEL TANK PRESSURETEMPERATURE SENSOR. The internal sealing of the fuel tank pressure-temperature sensor may fail. As a result, the sensor may read an incorrect value and set a fault code for the fuel tank evaporation system. This may lead to the Malfunction Indicator Lamp (MIL) being illuminated.
B6518162018-11-26. Service bulletin. AIR BAGS. The airbag warning lamp in the instrument cluster lights up while the vehicle is in motion. The airbag control unit (ACSM4) contains the following fault(s): ? 930904 - Drivers airbag interval stage 1, resistance too high ? 93090A - Drivers airbag interval stage 2, resistance too high Tension caused by harness cable tie on short jumper harness located between steering column slip ring and driver's airbag creates excess resistance.
B6126172018-11-26. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Charging of the high voltage battery is interrupted and will not complete. A change in the job structure in ISTA causes the BDC to open the 30B relay unexpectedly.
B6608152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Comfort Access Does Not Function After Vehicle Enters Sleep Mode. Sporadically, when the vehicle has been locked and is in sleep mode, the vehicle will not waken when trying to unlock the vehicle with comfort access from any door. The vehicle can be unlocked from the remote. After waking, the comfort access function is restored. Software fault in the BDC.
B6509152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
B6102152018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. Clicking Noise from Off-board Charger. While the vehicle is charging, the off-board charger is clicking. The clicking noise comes from the relays inside the charger cycling off and on. This condition most commonly occurs when the vehicle is fully charged; it is plugged into the charger; and then pre-conditioning is activated via the BMW iRemote app. The cycling of the relays can last from a few seconds to several minutes. Despite this cycling, the vehicle will continue to charge and pre-condition normally. While this condition can affect any off-board charger brand (Level 1 or 2), the Clipper Creek HCSSeries (Level 2/240V) charger tends to be more susceptible. CAUSE This situation is caused by an EME software issue that allows, depending on the electrical load demand from the vehicle, the charging to cycle on and off excessively.
B2201152018-11-13. Service bulletin. STRUCTURE; ENGINE AND ENGINE COOLING. ?SI B22 01 15 November 2015 Engine and Gearbox SuspensionTechnical Service This Service Information bulletin supersedes SI B22 01 15 dated February 2015. designates changes to this revision SUBJECT Left Side Engine Mount Broken. The left side motor mount or motor mount support has failed. As a result, the electric drivetrain moves excessively in the chassis. A banging noise can be heard from the rear of the vehicle during load reversals. In addition, the vehicle may experience a Drivetrain Malfunction CCM or other electrical drivetrain failures. NOTE: If this failure is present, the vehicle should not be driven, as additional consequential damage could result. CAUSE The motor mount or motor mount support is damaged due to excessive shock to the driveline, such as a sudden loss of traction or underbody impact, during acceleration.
B1238152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Various Software Fixes and Improvements. A number of undesirable conditions exist in these vehicles. This bulletin addresses the following customer complaints, system faults and improvements: ? Broken motor mount potential - (i3, SI B22 01 15) ? Low Cost Charging complaints - (i3) ? Vehicle will not charge at a power level below 600 watts - (i8) ? EME FC - 2228B8 (i8) ? EME FC - 2228BF (i3 & i8, SI B12 28 15) ? EME FC - 222011 (i3 & i8, SI B12 30 15) ? Clicking noise from Level 2 charger during charging (i3, SI B61 02 15) ? Addition of Hospitality Charging Feature (vehicles up to 3/15) - When the vehicle is locked and charging, the charge port will unlock when the vehicle is fully charged (i3) ? Various fault codes that will set a check engine light (CEL): EME- CF948C (SI B12 12 15), 22223D, 222AF4/6/8, 2228B8, 222321 (SI B12 22 15), RDME- 106002, 109009, 128002 (SI B12 34 15), EDME - 21E96F, SME - 21F0D3 (SI B12 11 15), IHKA - 801375 (SI B12 27 15) Various software errors.
B1234152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. "Service Engine Soon (MIL) - RDME FC 128002. The Service Engine Soon light (MIL) is illuminated in the instrument cluster and fault code 128002 ""Air mass: Too low"" is stored in the RDME. CAUSE RDME software."
B1230152018-11-13. Service bulletin. ELECTRICAL SYSTEM. "EME Fault Code: 222011. ? It is not possible to engage any drive position and/or the display on the gear selector switch (GWS) returns back to ""P"" and ""P"" begins to flash. ? Check Control Messages (CCM): 170 ""Drivetrain fault!"" and/or 633 ""Drivetrain fault!"" is displayed in the instrument cluster. ? Fault code 222011 ""Electrical machine, rotor position sensor, signal: Rotor position sensor adjustment not yet performed"" is stored in the Electrical Machine Electronics (EME). CAUSE EME software."
B1228152018-11-13. Service bulletin. ELECTRICAL SYSTEM. "EME Fault Code: 2228BF. Check control message (CCM) 170 ""Drivetrain fault"" is displayed in the instrument cluster and fault code 2228BF ""EME: internal fault (drive position monitoring)"" is stored in the Electrical Machine Electronics (EME). This could also be accompanied by EME fault code 222852 ""Gear position actuator, monitoring parking lock position: P incorrectly engaged"". CAUSE EME software."
B1227152018-11-13. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "Service Engine Soon (MIL) - IHKA FC 801375. The Service Engine Soon light (MIL) is currently or intermittently illuminated in the instrument cluster and fault code 801375 ""Electric auxiliary heater (high voltage) is stored: Temporary fault detected after software reset ""is stored in the Automatic Climate Control (IHKA). CAUSE IHKA software or Electric Heater (EH)."
B3601152018-11-13. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B3205142018-11-13. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR; STEERING. "Steering Wheel Does Not Return to Center. INFORMATION Do not replace any parts for this complaint. The return behavior is inherent in the design of the EPS. An EPS ""break in"" period of approximately 2000 miles is required. Once this phase is completed, the level of friction is significantly reduced and no longer affects the return to center. Please use this information to educate the customer on the ""break in"" period of the EPS. WARRANTY INFORMATION Not applicable."
B6108152018-11-13. Service bulletin. ELECTRICAL SYSTEM. "High-Voltage Charging Cable Lock Malfunction. One of the following situations can occur: ? The vehicle cannot be charged via the high-voltage charging procedure. The indicator light on the charging socket lights up white and does not change colors. ? The high-voltage charging cable cannot be unlocked and disconnected. One of the following faults codes is also stored in the Charging Interface Module (LIM): 805532 ""High-voltage charging socket: Lock on the charging plug, status implausible"" 805503 ""High-voltage charging socket: Charging plug lock, line disconnection"" CAUSE ? The emergency-operation tensioning strap is jammed. ? The actuator drive for the charging socket is not working."
B3601152018-11-13. Service bulletin. TIRES; WHEELS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B1212152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Service Engine Soon (MIL): EME FC CF948C. The Service Engine Soon light (MIL) is intermittently illuminated in the instrument cluster (Kombi). This does not affect drivability, and no symptoms are apparent to the customer. CAUSE The following fault code is stored in the fault memory of the Electric Machine Electronics (EME): ? CF948C - Message (actual wheel speed, 0x254) missing, receiver EME, transmitter DSC This fault is stored when the DSC control unit intermittently does not send a particular wheel speed message at the time the EME is expecting to receive it.
B8405142018-11-13. Service bulletin. EQUIPMENT. One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
B6503152018-11-13. Service bulletin. AIR BAGS. "Airbag Warning Light ON: Fault 930BE3, High-voltage System Shutdown. The airbag warning light in the instrument cluster is on, or the check control message (CCM) ""Restraint system faulty"" is displayed. The advance crash safety module (ACSM4I) control has fault code 930BE3 ""High-voltage system switch-off (EME/convenience charging electronics/auxiliary battery): Resistance too high"" stored. A sporadically poor connection causes high resistance in the airbag ignition circuit."
B6135142018-11-13. Service bulletin. ELECTRICAL SYSTEM. "General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 35 14 dated December 2014. designates changes to this revision SUBJECT Displayed Range Is Lower After Programming. After the vehicle is programmed with ISTA/P 3.53.3 (i-level I001-14-07-503), the displayed vehicle range in the instrument cluster is lower than prior to the software update. The actual range that the vehicle is capable of achieving on a full charge has not changed. The difference between the displayed range and actual range is always conservative, yet this difference varies based on driving profile. When driving primarily at highway speeds, the difference between displayed and actual range is within a few percent of each other. When driving primarily with a low speed/city profile, the gap may widen to as much as 20% or more. Software improvements have been made to the range algorithm to improve its accuracy in all driving scenarios. These updates are available with ISTA/P 3.55.0 (I-level I001-15-03-501). In addition, the following enhancements are integrated into this new I-level: ? The state of charge (SOC) percentage is visible in the upper left corner of the Kombi. It has been added to the board computer display in order for the customer to better manage the vehicle range. ? During vehicle charging with the doors locked, the charge port is also locked. However, now when charging commences, the charge port will be unlocked to allow for hospitality charging (charger sharing). ? REx only - if the SOC reaches 2.0% with the REx running, the message ""Low Battery. Power Reduction Possible."" will appear in the Kombi. In addition to the range display, the customer may notice that the vehicle's range has decreased as outside temperatures have gotten colder. This is most noticeable in extreme cold climates, and when preconditioning is not used. This situation does not indicate a problem and is independent of the range display algorithm. CAUSE The algorithm
B6105152018-11-13. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. 12-volt Battery Terminal Adapter Slightly Loose. The 12-volt battery adapter appears to be slightly loose. The cable connection on the positive or negative terminal can be slightly moved or turned. It is normal for vehicles to have slight play in the adapter for battery connections. Vehicles produced prior to April 3, 2014 may have excessive play because the mounting screw is not microencapsulated and can loosen further.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.