Service bulletins for the 2013 Audi A5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1378 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Electrical system are shown. Show all
| A451408 2033412- | 2017-12-14. Service bulletin. STEERING; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 45 number 13-07 dated September 25, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. There are DTC entries present in the system (either static or sporadic). DTCs with description ?Brake control module - no signal/communication? are present in several control units. DTCs are stored in the ABS control module. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected. |
|---|---|
| A201443 2035073- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 20 number 14-41 dated October 9, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak. |
| A001470 2039206- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM. High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices. |
| A911469 2038824- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES. The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices. |
| A201437 2038276- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM. DTC P045600 is stored in the engine control module (ECM), J623 (address word 01). Note that this repair authorization applies only to a specific list of VINs. If this repair authorization does not appear in ELSA when your VIN is entered, it does not apply. |
| A911458 2035919- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 14-53 dated July 24, 2014. MMI 3G+ GPS location is inaccurate (MY13, MY14, & MY15). |
| A911459 2036607- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 14-42 dated April 30, 2014. The GPS location or vehicle direction indicated on the navigation map does not match the actual vehicle?s location or actual direction of travel. The condition can happen sporadically or consistently. The condition does not happen during or immediately following the initial PDI inspection (once the vehicle has been taken out of transport mode). It is normal for the satellite reception to be 0 immediately after taking the vehicle out of transport mode. With the ignition off, the vehicle must sit in open sky view for 10-15 minutes before a GPS fix can be obtained. The vehicle is a Model Year 2013. |
| A911463 2028190- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not. |
| A461357 2031135- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 46 number 12-26 dated October 23, 2012. The yellow warning for electromechanical parking park (EPB) appeared once in the instrument cluster. The warning turned off after the ignition was cycled, and there have not been additional occurrences. EPB function was not affected. The adaptive cruise control (ACC) was inoperative once, but it resumed proper operation after the ignition was cycled, and there have not been additional occurrences. DTCs are logged in the EPB control module. There is an issue with the software in the EPB control module that occurs one time. Because the issue only occurs once, replacing the control module could cause an additional occurrence. |
| A801304 2033806- | 2017-12-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ELECTRICAL SYSTEM:WIRING. Supersedes Technical Service Bulletin Group 80 number 13-03 dated May 13, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. "Limp Home" mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant. |
| A961372 2035047- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; LANE DEPARTURE: ASSIST. Audi Lane Change Assistant deactivates or is sporadically inoperative when the vehicle is driven in slow-moving stop-and-go traffic, especially on roads with multiple lanes. The message "Audi side assist unavailable: Sensors blocked" appears in the driver information system. The system is able to be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. Audi Lane Change Assistant can be activated without issue. No obstructions can be found. DTCs are stored in the Lane Change Assistance control module. The control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found to the rear bumper area, on the inside or outside. (If any damage is found, it is not covered under warranty.) The control module mounting brackets are not broken or loose. If a loose bracket is found, repair as necessary using the Elsa Repair Manual. Submit a separate warranty claim, as this TSB does not cover this repair. The software of the Lane Change Assistance control module can deactivate the Audi Side Assist system in certain normal driving conditions because the nature of these driving conditions make it difficult for the Audi Side Assist system to track vehicles. |
| A911392 2030947- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding. |
| A911388 2021780- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 10-70 dated October 26, 2010. Sequence of error messages are seen on the radio display screen after a CD was loaded into or removed from the internal CD drive. "Drive defective. The error could be corrected by resetting it (see radio system owner's manual). Otherwise, contact your Audi dealer." "The CD-drive is damaged and was therefore deactivated." The CD drive cannot be selected in the Source list and is described as "damaged." After the ignition is cycled or a radio reset performed, the CD drive is fully operational. DTC 00468 (CD-ROM Drive -R92- Faulty) is stored in the radio (address word 56). The DTC will be sporadic if the ignition has been cycled or a radio reset performed and will automatically be cleared after 40 ignition cycles without a reoccurrence. Only vehicles with the CAN-based generation 3 radio (Concert (PR 8UQ) or Symphony (PR 8YN)) are affected. |
| A551332 2023967- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD; LATCHES/LOCKS/LINKAGES:HOOD:LATCH. Supersedes Technical Service Bulletin Group 55 number 13-30 dated May 28, 2013. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the hood has not been recognized as being opened due to an inoperative hood contact switch. |
| A531302 2034404- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE. Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module, J540 (address word 53). According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object. Test plan "19-Read Data Bus Keep-Awake Manager", identifies the EPB control module as keeping the data bus active for prolonged periods of time. |
| A461348 2034404- | 2017-12-05. Service bulletin. PARKING BRAKE; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 53 number 13-02 dated July 11, 2013. Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module, J540 (address word 53). According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object. Test plan "19-Read Data Bus Keep-Awake Manager", identifies the EPB control module as keeping the data bus active for prolonged periods of time. |
| A461347 2034387- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE. Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated. |
| A941306 2017806- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared. |
| A911375 2032966- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. No sound (from all audio sources) when vehicle is operated above 6 to 10 mph. When the ignition is cycled and the vehicle is stationary, the audio will work until the vehicle is driven again. Concert Radio (PR 8UQ) and standard sound system (PR 9VD). |
| Update Bulletin | 2017-11-17. Service bulletin. LANE DEPARTURE: ASSIST; ELECTRICAL SYSTEM:SOFTWARE. On Audi vehicles with lane change assist manufactured within a specific period, the lane change assist control unit may fail in individual cases after a period of time. The Update is in effect until removed. Procedure is valid only for vehicles that show the 96C8 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicles must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted timeframe stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. |
| A371399 2029027- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Supersedes Technical Service Bulletin Group 37 number 12-77 dated December 19, 2012. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module, J217 (02). If DFCCs do not match exactly, this TSB does not apply. |
| A371302 2029027- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Supersedes Technical Service Bulletin Group 37 number 13-99 dated April 1, 2013. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module (TCM), J217 (02). If DFCCs do not match exactly, this TSB does not apply. The DTCs are stored due to an issue with the transmission control module software. |
| A371301 2028985- | 2017-11-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 37 number 13-97 dated March 4, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or "Stuck Off" is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks. |
| A371396 2029305- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Supersedes Technical Service Bulletin Group 37 number 13-87 dated February 6, 2013. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration concerns. Further TCM software calibration to improve shift concerns. |
| A481341 2033391- | 2017-11-17. Service bulletin. STEERING:ELECTRIC POWER ASSIST SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. Customer may report that a warning for electromechanical steering is displayed in the instrument cluster. There is no loss of steering control or functionality associated with these warnings. Issues with the hardware and software. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.