NHTSA recall 13V570000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 13V570000 |
| Manufacturer | BMW of North America, LLC |
| Reported | 2013-11-15 |
| Owners notified | 2013-12-11 |
| Component | ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; AIR BAGS |
| Units potentially affected | 3 |
| Report | Quarterly report 6, for 2015 quarter 1 |
|---|---|
| Filed with NHTSA | 2015-05-01 |
| Vehicles in the campaign | 3 |
| Reported remedied | 3 (100%) |
| Reported unreachable | 0 |
| Reported removed | 0 |
These are the manufacturer's totals for the whole campaign at the end of 2015 quarter 1, as filed with NHTSA. They do not say whether one vehicle has been remedied: check the VIN with the official lookups. The reports are from data as of 2026-10-19.
What is wrong
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
What can happen
In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
The remedy
BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
| 2013 BMW X3 | Built 2013-02-11 to 2013-02-27. |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| B612115 | 2018-12-10. Service bulletin. The Instrument Cluster Displays Various Check Control Messages. The instrument cluster displays various check control messages. Signal invalid. The wiring harness below the micro filter housing (right front area of the bulkhead) is damaged from washer fluid leaking into the harness. |
|---|---|
| B612115 | 2018-12-10. Service bulletin. THE INSTRUMENT CLUSTER DISPLAYS VARIOUS CHECK CONTROL MESSAGES. The instrument cluster displays various check control messages. THE INSTRUMENT CLUSTER DISPLAYS VARIOUS CHECK CONTROL MESSAGES. The instrument cluster displays various check control messages. This includes messages for the PDC (Park Distance Control), DSC (Dynamic Stability Control) and windshield washer system. There can be many different fault codes stored in the vehicle. The wiring harness below the micro filter housing (right front area of the bulkhead) is damaged from washer fluid leaking into the harness. |
| 620613 | 2018-12-03. Service bulletin. Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster |
| 620313 | 2018-11-26. Service bulletin. Basic Instrument Cluster: Display Is Intermittently Inoperative. The display in the basic instrument cluster is intermittently inoperative. The following fault codes are stored in the instrument cluster: * B7F6B4 "Instrument cluster: Error in the display unit when switching off (NO SIGNAL)" and/or * B7F6AA "Display switch-off error when starting up" Software error in the instrument cluster |
| B621215 | 2018-11-13. Service bulletin. Instrument Cluster Outside Temperature Display Implausible. INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2. |
| B621015 | 2018-11-13. Service bulletin. "Instrument Cluster display inoperative FC B7F689. The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 ""display backlighting and graphics PCB switched off"" stored. Kombi software." |
| B620715 | 2018-11-13. Service bulletin. Instrument Cluster display is partially blank. The Instrument Cluster (Kombi) lower display may be intermittently blank. The Board Computer, Ambient Temperature and Check Control Messages will not display. Instrument Cluster software error. |
| 123514 | 2018-11-13. Service bulletin. This Service Information bulletin supersedes SI B12 35 14 dated December 2014. designates changes to this revision SUBJECT N20, N26 Service Engine Soon Light On: Fault Code 1B9702 is Stored. The Service Engine Soon light (MIL) is on with only the following fault stored in the DME: z 1B9702: Engine switch-off time, timer, instrument panel timer DME, Comparison: Value of instrument panel timer too low while engine is running This fault will not cause any engine running or drivability problems. Instrument cluster software error. |
| B621215 | 2018-05-21. Service bulletin. INSTRUMENT CLUSTER OUTSIDE TEMPERATURE DISPLAY IMPLAUSIBLE: In the Instrument Cluster (Kombi) display you may observe an implausible outside temperature reading. |
| SB-62-03-13 | 2013-04-18. Service bulletin. INSTRUMENT CLUSTER DISPLAY IS INTERMITTENTLY INOPERATIVE. BMW F25, AND F30 MODELS. *KB |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.