Service bulletins for the 2015 Ram 1500
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
590 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| 54931 | 2019-07-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. TAILPIPE - EXHAUST |
|---|---|
| 9003357 | 2019-07-15. Service bulletin. ENGINE; EQUIPMENT. ADAPTER, Engine Oil Filter (Pentastar V6) Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. |
| 18-019-15 REV C | 2019-05-20. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL; SERVICE BRAKES, HYDRAULIC; STRUCTURE. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience bucking under hard acceleration. In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P1296-00 - EGR Slow Response - Increasing Flow. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P24A4-00 - Particulate Filter Restriction - Soot Accumulation Too High. ? P24D1-00 - Particulate Matter Sensor Regeneration Incomplete. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1289-00 - NOx Sensor 1/2 Zero Offset Too Low. ? P2463-00 - Diesel Particulate Filter - Soot Accumlation . ? U0422-00 - Implausible Data Received From Body Control Module. ? U3017-00 - Control Module Timer/Clock Performance. ? P2196-00 ? O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 ? Empty Fuel Tank. ? P2237-00 ? O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 ? EGR Slow Response - Decreasing Flow. ? P0420-00 ? Catalyst Efficiency (Bank 1). ? P24AF-00 ? Particulate Matter Sensor Circuit Performance. ? P26AB ? Engine Coolant Bypass Valve Stuck. ? P204F-00 ? Reductant System Performance. ? P20E9-00 ? Reductant Pressure Too High. ? P2002-00 ? Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 ? Brake Pedal Position/Accelerator Pedal Position Incompatible. ? P208B-00 ? Reductant Pump 1 Control Performance. ? P016A-00 ? Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. Upon further investigation a technician may find the following Diagnostic Trouble Code (DTC) set in the TCM memory: ? U1424-00 - Implausible Engine Torque Signal Received |
| 05184349A | 2019-05-20. Service bulletin. ENGINE AND ENGINE COOLING. Before replacing this part for debris issue faults, please call the following people;~ Engineering is seeking information regarding this part.~ Bob Smith ? Cell (248) 202-9458 - Robert.M.Smith@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~ |
| R51 | 2019-05-20. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. The Charge Air Cooler (CAC) on about 7,600 of the above vehicles may develop internal icing in cold temperature regions. This condition may cause the Malfunction Indicator Light (MIL) to illuminate and cause the vehicle to experience a 35 mph limp in condition. A winter front cover must be installed when sustained day and night time temperatures drop below 30° F (-1° C). |
| 13284 | 2018-12-17. Service bulletin. ENGINE. Title Filter - Engine Oil Start Date: 10/23/2015 7:00 AM End Date Message You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part number: 68109834AA. Replacement part number is: 68229402AA. 68229402AA is designed to work on both DS and W K with 3.0L Ecodiesel(EXF)in NAFTA. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com. |
| 68080819A | 2018-11-26. Service bulletin. ENGINE. Camshaft Position Sensor If replacing a camshaft position sensor for P0340 and/or P0344 fault codes, please review information below and contact Andrew Action on his cell phone: (248) 421- 4130. If no response is received within 15 minutes, please continue with repair.~ Before clearing any codes please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Andrew Acton by email: andrew.acton@fcagroup.com~ Instructions to access CamCrank Sync Event Monitor:~ - From wiTECH main screen~ - Monitors tab~ - OBDII Monitors~ - Select Cam Crank Synchronization Event Monitor from the list~ - Should bring up 3 or 4 pages of data~ - Click on create PDF icon in lower right corner~ - email PDF to andrew.acton@fcagroup.com |
| 68079375A | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Crankshaft Position Sensor Before replacing this part due to a P0335 fault code, please contact Andrew Acton at cell (248) 421-4130. Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data. |
| 05191925A | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked. |
| 05149141A | 2018-11-26. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Camshaft Position Sensor If replacing a camshaft position sensor for P0340, P0344, P0345, P0349, P0365, P0369, P0390 or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com |
| 04861963A | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT. Evaporative System Integrity Monitor switch (ESIM) Prior to replacing this component on a 2015 Dodge Journey (JC), please call Bob Bruni at cell (248) 736-8958. If a response is not received within 15 minutes, then continue with the necessary repair. |
| 07-004-15 REVA | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Malfunction Indicator Lamp (MIL) Illuminated DTC P1D73 Active Grill Shutter (AGS) Performance This bulletin involves inspecting and securing the AGS actuator motor case housing. The customer may describe the MIL is illuminated. On further inspection the technician may find the following Diagnostic Trouble Code (DTC) P1D73 Active Grill Shutter (AGS) Performance. |
| 07-004-15 | 2018-09-24. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT ADAPTIVE/MOBILITY. Malfunction Indicator Lamp (MIL) Illuminated DTC P1D73 Active Grill Shutter (AGS) Performance This bulletin involves inspecting and securing the AGS actuator motor case housing. The customer may describe the MIL is illuminated. On further inspection the technician may find the following Diagnostic Trouble Code (DTC) P1D73 Active Grill Shutter (AGS) Performance. |
| 18-019-15 | 2018-09-24. Service bulletin. ENGINE. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P20C2 - Reductant Heater 3 Control Circuit Performance. ? P204F - Reductant System Performance. ? P20E9 - Reductant Pressure Too High. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? Enhancements to improve A/C compressor relay duty cycle operation to prevent ignition off battery draw. ? Powertrain system improvements to enable EGR cleaning routine. |
| 68225378A$ | 2018-06-18. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). 3.0L V6 Turbo Diesel - Sales Code EXF A crankshaft locking tool marked 630 is installed on all 3.0L EXF long blocks (Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~ |
| 68225378A$ | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. 3.0L V6 Turbo Diesel - Sales Code EXF A crankshaft locking tool marked 630 is installed on all 3.0L EXG long blocks (Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~ |
| 22842 | 2018-06-11. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. 05187880AC - Inspect and Return: Relay Assy - Heater Intake Air You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016. |
| 20610 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. P/N 04573460 - Inspect &Return: Rocker Assy - Intake Valve RT You have been identified as either having stock, or have stock in transit to your dealership. Please return part number 04573460 which have a packaging date of 2016-06-13. Reference attached picture for reference. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016. |
| 17006 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. 68085119AE,Inspect and Return: Exhaust Pipe Assy - Frt W/Catalytic Converter You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com. |
| 16887 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. Return: ALTERNATOR - ENGINE You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com |
| 30731 | 2018-06-11. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. 04627694AA Purge Control - Valve You have been identified as either having stock, or have stock in transit to your dealership. Suspect stock of part number: 04627694AA must be returned. See attached for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017. |
| 9003694 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system |
| 68105583A | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~ |
| 23-004-16 REV. B | 2018-05-07. Service bulletin. ENGINE AND ENGINE COOLING. Tailgate Contacting Pickup Box Panel When Closing This bulletin involves adjusting the passenger side outer box flange. The customer may describe the tailgate making contact with the passenger side outer box panel. |
| RL108213A$ | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~ |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.