WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Nissan Juke

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

126 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
NTB12055E2021-05-10. Service bulletin. WHEELS; POWER TRAIN; EQUIPMENT; BACK OVER PREVENTION. IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear CV-type axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. - For 2007-2013 Versa and 2013 LEAF vehicles, see the Service Procedure torque specifications on page 4. See this bulletin for further detail.
NTB150602021-05-10. Service bulletin. SERVICE BRAKES; WHEELS; BACK OVER PREVENTION; STEERING; EQUIPMENT. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
NTB150552021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
NTB150432021-05-10. Service bulletin. WHEELS. SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
NTB150352021-05-10. Service bulletin. LANE DEPARTURE. SERVICE INFORMATION If you confirm there is a need to replace the combination meter front cover (lens) on an Applied Vehicle for any reason (scratch, blemish, etc.): - Do not replace the entire combination meter assemby. The front cover of the combination meter assembly is available as a separate service part. - Refer to the Electronic Service Manual, section MWI-Meter, Warning Lamp & Indicator, for replacement information. See this bulletin for further detail.
NTB14088B2021-05-10. Service bulletin. BACK OVER PREVENTION; STEERING; SUSPENSION; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); SEATS; EQUIPMENT; WHEELS. IF YOU CONFIRM: There is a noise (clunking, popping, or bumping) when the steering wheel is turned AND the noise is coming from the top of either front strut assembly. NOTE: The location of the noise can be determined by using Essential Tool J39570 (Chassis Ear), positioning a clamp on each front strut spring, and then turning the steering wheel back and forth. ACTION: Install a spacer in both the left front and right front strut assemblies where shown in this bulletin. - Refer to the Electronic Service Manual (ESM), section FSU- Front Suspension for removal and installation instructions. See this bulletin for further detail.
NTB10112E2021-05-10. Service bulletin. WHEELS. SERVICE INFORMATION For vehicles delivered to the dealers with wheel protector covers - Do not remove the wheel protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.
NTB99060G2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain, iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
NTB00042D2021-05-10. Service bulletin. AIR BAGS; BACK OVER PREVENTION; EQUIPMENT. SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB13015A2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
NTB141092021-05-10. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
NTB141072021-05-10. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
NTB10066A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
P4213D2021-05-10. Service bulletin. ENGINE; EQUIPMENT. We were temporarily using an alternate part (13094-31U00) as a substitute to fill VOR & CSC part backorders.
P4213C2021-05-10. Service bulletin. ENGINE; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Due to the damage of the Slack Guide Bolt (13094-EN200) during the removal procedure and the unforeseen part demand for the campaign, the slack guide bolt has been on backorder the last two weeks. Nissan will use part 13094-31U00 (Slack Guide Bolt-Alternative) as a temporary alternative to fill all VOR and CSC part backorders, which will arrive by Friday, 5/23 via FedEx.
P4213B2021-05-10. Service bulletin. EQUIPMENT; ENGINE. Nissan recently learned that a bolt that is removed (and reused) in the campaign procedure can be stripped if using a power tool, rendering it unusable. This has created a flow of dealer orders and a backorder situation for part 13094-EN200.
P4213OL2021-05-10. Service bulletin. ENGINE; EQUIPMENT. Nissan is conducting this Voluntary Service Campaign to replace the engine timing chain on certain specific 2011 ? 2013 Juke vehicles.
P4213A2021-05-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. Dealers can order additional parts as needed.
NTB140322021-05-10. Service bulletin. ELECTRICAL SYSTEM:WIRING. SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
P42132021-05-10. Service bulletin. ENGINE. Nissan is conducting this Voluntary Service Campaign to replace the engine timing chain on certain specific 2011 ? 2013 Juke vehicles.
NTB08055C2021-05-10. Service bulletin. EQUIPMENT; AIR BAGS. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB12091A2021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); ENGINE. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
NTB11005D2021-05-10. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
NTB92123D2021-05-10. Service bulletin. WHEELS; EQUIPMENT. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
NTB13027A2021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.