Service bulletin NTB15035

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10192561
Published by NHTSA	2021-05-10
Manufacturer's number	NTB15035
Manufacturer's date	2015-04-20
NHTSA component	LANE DEPARTURE

NHTSA's summary

SERVICE INFORMATION If you confirm there is a need to replace the combination meter front cover (lens) on an Applied Vehicle for any reason (scratch, blemish, etc.): - Do not replace the entire combination meter assemby. The front cover of the combination meter assembly is available as a separate service part. - Refer to the Electronic Service Manual, section MWI-Meter, Warning Lamp & Indicator, for replacement information. See this bulletin for further detail.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Driver assistance

Vehicles listed
NISSAN ARMADA	2013, 2014, 2015
NISSAN CUBE	2013, 2014
NISSAN FRONTIER	2013, 2014, 2015
NISSAN GT-R	2013, 2014, 2015
NISSAN JUKE	2013, 2014, 2015
NISSAN LEAF	2013, 2014, 2015
NISSAN MURANO	2013, 2014, 2015
NISSAN NV	2013, 2014, 2015
NISSAN NV200	2013, 2014, 2015
NISSAN NV200 TAXI	2014, 2015 (the catalog's model; the bulletin names a series or trim of it)
NISSAN QUEST	2013, 2014, 2015
NISSAN ROGUE	2013, 2014, 2015
NISSAN SENTRA	2013, 2014, 2015
NISSAN TITAN	2013, 2014, 2015
NISSAN VERSA	2013, 2014, 2015
NISSAN VERSA NOTE	2014, 2015
NISSAN XTERRA	2013, 2014, 2015

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
NTB19-042F	2025-02-25. Service bulletin. AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: • When contamination or foreign material adhere to the lane camera viewing window on the windshield. • When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. • When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: • Refer to the following pages. • Use the search keyword “blinking” in the ESM.
NTB19-033G	2025-02-25. Service bulletin. INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042E	2024-06-07. Service bulletin. AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D	2023-04-07. Service bulletin. AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042C	2022-02-10. Service bulletin. AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106	2022-01-08. Service bulletin. DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the “PAST” column: • Erase the DTC. • DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
NTB13106E	2021-05-10. Service bulletin. SERVICE INFORMATION If the configuration of the Audio/Navigation unit has not been completed correctly, some of the symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail.
NTB09131B	2021-05-10. Service bulletin. SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB15073B	2021-05-10. Service bulletin. IF YOU CONFIRM The automatic back door does not operate and/or one or a combination of the following DTCs are found stored in the Automatic Back Door Control Module (ABD CU): - B2426-29 (SPINDLE SENSOR LH) - B2427-29 (SPINDLE SENSOR RH) - B2416-1E (TOUCH SEN R OPEN) - B2417-1E (TOUCH SEN L OPEN) - B242A-13 (CLSR CONDITION) ACTION 1. Check the battery voltage (engine not running). - Make sure battery voltage is between 12 and 15.5 volts. - Charge or replace the battery as needed. 2. For 2015 Murano Only: Refer to page 9, step 13 in the Service Procedure to confirm if ABD CU reprogramming is needed. - Reprogram the ABD CU, if needed. - If the ABD CU is reprogramed, also perform Automatic Back Door Manual Configuration. 3. Perform Automatic Back Door Calibration (see page 22). 4. Erase all DTCs. 5. For 2015 Murano Only: If reprogramming was done, inform the customer of changes in automatic back door operation (see page 3, and also Owner?s Manual pages at the end of this bulletin. See this bulletin for further detail.
NTB16025	2021-05-10. Service bulletin. SERVICE INFORMATION If an Air Bag Diagnosis Sensor Unit is replaced and the configuration of the old unit could not be saved, use the Service Procedure in this bulletin to: - Load the VIN specific configuration file from your electronic parts catalog (FAST or equivalent) onto a portable USB storage device (thumb drive) - Plug the thumb drive into your CONSULT PC. - Configure the new Air Bag Diagnosis Sensor Unit using the file that you loaded onto the thumb drive. See this bulletin for further detail.