Service bulletin NTB15073B
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10192783 |
| Published by NHTSA | 2021-05-10 |
| Manufacturer's number | NTB15073B |
| Manufacturer's date | 2016-03-22 |
| NHTSA component | EQUIPMENT; VEHICLE SPEED CONTROL; ELECTRICAL SYSTEM; BACK OVER PREVENTION |
NHTSA's summary
IF YOU CONFIRM The automatic back door does not operate and/or one or a combination of the following DTCs are found stored in the Automatic Back Door Control Module (ABD CU): - B2426-29 (SPINDLE SENSOR LH) - B2427-29 (SPINDLE SENSOR RH) - B2416-1E (TOUCH SEN R OPEN) - B2417-1E (TOUCH SEN L OPEN) - B242A-13 (CLSR CONDITION) ACTION 1. Check the battery voltage (engine not running). - Make sure battery voltage is between 12 and 15.5 volts. - Charge or replace the battery as needed. 2. For 2015 Murano Only: Refer to page 9, step 13 in the Service Procedure to confirm if ABD CU reprogramming is needed. - Reprogram the ABD CU, if needed. - If the ABD CU is reprogramed, also perform Automatic Back Door Manual Configuration. 3. Perform Automatic Back Door Calibration (see page 22). 4. Erase all DTCs. 5. For 2015 Murano Only: If reprogramming was done, inform the customer of changes in automatic back door operation (see page 3, and also Owner?s Manual pages at the end of this bulletin. See this bulletin for further detail.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Driver assistance, Electrical system, Equipment and accessories, Throttle and cruise control, Backup camera
Trouble codes named
B2416, B2417, B2426, B2427, B242A
| NISSAN MURANO | 2015, 2016 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| NTB16025 | 2021-05-10. Service bulletin. SERVICE INFORMATION If an Air Bag Diagnosis Sensor Unit is replaced and the configuration of the old unit could not be saved, use the Service Procedure in this bulletin to: - Load the VIN specific configuration file from your electronic parts catalog (FAST or equivalent) onto a portable USB storage device (thumb drive) - Plug the thumb drive into your CONSULT PC. - Configure the new Air Bag Diagnosis Sensor Unit using the file that you loaded onto the thumb drive. See this bulletin for further detail. |
|---|---|
| NTB16023 | 2021-05-10. Service bulletin. IF YOU CONFIRM A customer concern of while turning the steering wheel or when driving at low speed (straight or turning), a high pitch power steering noise can be heard. * Only while seated inside the vehicle And * With all of the windows up NOTE: If the audio and/or HVAC systems are turned ON it may be difficult to hear this issue. ACTION Install an Insulator onto the end of the power steering pump motor housing with the Service Procedure starting on the next page. Please see this bulletin for further details. |
| NTB13088A | 2021-05-10. Service bulletin. SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail. |
| NTB15060 | 2021-05-10. Service bulletin. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail. |
| NTB00042D | 2021-05-10. Service bulletin. SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail. |
| NTB16-077 | 2017-02-14. Service bulletin. "2016 MURANO, ROGUE AND PATHFINDER; AROUND VIEW MONITOR MIRROR CAMERA INOPERATIVE IF YOU CONFIRM - EITHER THE LEFT OR RIGHT AROUND VIEW MONITOR DOOR MIRROR CAMERA IS INOPERATIVE. NOTE: THE FOLLOWING DTCS MAY ALSO BE PRESENT: - U111B (SIDE CAMERA LH IMAGE SIGNAL CIRCUIT) DTC IS STORED. AND/OR - U111D (SIDE CAMERA RH IMAGE SIGNAL CIRCUIT) DTC IS STORED. ACTION CHECK THE SIDE CAMERA HARNESS CONNECTION BETWEEN THE SIDE CAMERA AND THE MIRROR HARNESS LOCATED INSIDE THE INOPERATIVE DOOR MIRROR. - IF THE HARNESS CONNECTOR IS NOT LATCHED (CAN BE DISCONNECTED BY A GENTLE TUG), SEAT THE CONNECTOR, CLEAR THE DTC AND RETEST. - IF THE HARNESS CONNECTOR IS LATCHED (CANNOT BE DISCONNECTED BY A GENTLE TUG) REFER TO THE ELECTRONIC SERVICE MANUAL (ESM) FOR FURTHER DIAGNOSTIC INFORMATION. NOTE: IF A SIDE CAMERA REQUIRES REPLACEMENT, DO NOT REPLACE THE ENTIRE MIRROR, REPLACE ONLY THE SIDE CAMERA." |