Service bulletin NTB15060
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10192597 |
| Published by NHTSA | 2021-05-10 |
| Manufacturer's number | NTB15060 |
| Manufacturer's date | 2015-07-06 |
| NHTSA component | SERVICE BRAKES; WHEELS; BACK OVER PREVENTION; STEERING; EQUIPMENT |
NHTSA's summary
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Brakes, Driver assistance, Equipment and accessories, Steering, Wheels, Backup camera
| NISSAN 350Z | 2007, 2008, 2009 |
|---|---|
| NISSAN 370Z | 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016 |
| NISSAN ALTIMA | 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 |
| NISSAN ARMADA | 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 |
| NISSAN CUBE | 2009, 2010, 2011, 2012, 2013, 2014 |
| NISSAN FRONTIER | 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 |
| NISSAN GT-R | 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016 |
| NISSAN JUKE | 2011, 2012, 2013, 2014, 2015 |
| NISSAN LEAF | 2011, 2012, 2013, 2014, 2015 |
| NISSAN MAXIMA | 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014 |
| NISSAN MAXIMA | 2016 |
| NISSAN MURANO | 2007 |
| NISSAN MURANO | 2009, 2010, 2011, 2012, 2013, 2014, 2015 |
| NISSAN NV | 2012, 2013, 2014, 2015 |
| NISSAN NV200 | 2013, 2014, 2015 |
| NISSAN NV200 TAXI | 2014, 2015 (the catalog's model; the bulletin names a series or trim of it) |
| NISSAN PATHFINDER | 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 |
| NISSAN QUEST | 2007, 2008, 2009 |
| NISSAN QUEST | 2011, 2012, 2013, 2014, 2015 |
| NISSAN ROGUE | 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 |
| NISSAN SENTRA | 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 |
| NISSAN TITAN | 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 |
| NISSAN VERSA | 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 |
| NISSAN VERSA NOTE | 2014, 2015 |
| NISSAN XTERRA | 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015 |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| NTB13106E | 2021-05-10. Service bulletin. SERVICE INFORMATION If the configuration of the Audio/Navigation unit has not been completed correctly, some of the symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail. |
|---|---|
| NTB15073B | 2021-05-10. Service bulletin. IF YOU CONFIRM The automatic back door does not operate and/or one or a combination of the following DTCs are found stored in the Automatic Back Door Control Module (ABD CU): - B2426-29 (SPINDLE SENSOR LH) - B2427-29 (SPINDLE SENSOR RH) - B2416-1E (TOUCH SEN R OPEN) - B2417-1E (TOUCH SEN L OPEN) - B242A-13 (CLSR CONDITION) ACTION 1. Check the battery voltage (engine not running). - Make sure battery voltage is between 12 and 15.5 volts. - Charge or replace the battery as needed. 2. For 2015 Murano Only: Refer to page 9, step 13 in the Service Procedure to confirm if ABD CU reprogramming is needed. - Reprogram the ABD CU, if needed. - If the ABD CU is reprogramed, also perform Automatic Back Door Manual Configuration. 3. Perform Automatic Back Door Calibration (see page 22). 4. Erase all DTCs. 5. For 2015 Murano Only: If reprogramming was done, inform the customer of changes in automatic back door operation (see page 3, and also Owner?s Manual pages at the end of this bulletin. See this bulletin for further detail. |
| NTB16025 | 2021-05-10. Service bulletin. SERVICE INFORMATION If an Air Bag Diagnosis Sensor Unit is replaced and the configuration of the old unit could not be saved, use the Service Procedure in this bulletin to: - Load the VIN specific configuration file from your electronic parts catalog (FAST or equivalent) onto a portable USB storage device (thumb drive) - Plug the thumb drive into your CONSULT PC. - Configure the new Air Bag Diagnosis Sensor Unit using the file that you loaded onto the thumb drive. See this bulletin for further detail. |
| NTB16023 | 2021-05-10. Service bulletin. IF YOU CONFIRM A customer concern of while turning the steering wheel or when driving at low speed (straight or turning), a high pitch power steering noise can be heard. * Only while seated inside the vehicle And * With all of the windows up NOTE: If the audio and/or HVAC systems are turned ON it may be difficult to hear this issue. ACTION Install an Insulator onto the end of the power steering pump motor housing with the Service Procedure starting on the next page. Please see this bulletin for further details. |
| NTB15102 | 2021-05-10. Service bulletin. IF YOU CONFIRM: A whine or grind type noise heard during acceleration and/or constant highway speeds. -The level of noise may increase as vehicle speed increases AND there are no other drivability issues or stored DTCs related to the CVT assembly (CVT). ACTION: Refer to the REPAIR FLOW CHART on page 3 for repair procedure. Refer to page 2 for information on special service tools. NOTE: Parts Kit #1 (see PARTS INFORMATION) must be available at the time the reduction gear bearing shim selection procedure, starting on page 11, is to be performed. See this bulletin for further detail. |
| NTB13079D | 2021-05-10. Service bulletin. IF YOU CONFIRM: The vehicle speed is, or was, reduced by the CVT fail-safe (reduced vehicle speed) after continuous operation under the following conditions: * High RPM and/or high speed driving (RPM of 4000+ or speeds of 65 mph (104.6 km/h) for 1.0 - 1.5hrs or more) * Driving in ambient temperature of 96 degrees or higher * Climbing steep or extended hills for 6 miles (9.6 km) or more * Whine or rattle type noise occurring during reduced engine performance (vehicle speed decrease) ACTIONS: Install the SERVICE KIT-COOLER ASSY. See this bulletin for further detail. |
| NTB15062A | 2021-05-10. Service bulletin. IF YOU CONFIRM There is a popping noise from either the right or the left front coil springs when turning to the right or left. NOTE: Electronic chassis ears may be helpful in isolating this type of noise. ACTION Replace both front coil springs, strut mount bearings, and all other parts listed under PARTS INFORMATION. Position the coil springs as shown on pages 2-5. Check the front end alignment, adjust to factory specifications as needed. NOTE: Refer to the Electronic Service Manual (ESM), section FSU Front Suspension, for strut coil spring removal, installation, and alignment information. IMPORTANT: The Coil Spring Installation Guidelines section in this bulletin MUST be followed in order for a correct repair to be performed. |
| NTB15082 | 2021-05-10. Service bulletin. IF YOU CONFIRM: An APPLIED VEHICLE has one or both of the following: * Hesitation during acceleration * MIL ON with DTC P0705 (Transmission Range Sensor A Circuit (PRNDL Input)) stored ACTION: 1. Inspect both rear tail lamp assemblies forwater intrusion (see page 2 for sample pictures). 2. If water intrusion is detected, inspect the circuit board of the tail lamp bulb holder(s) for corrosion (see page 2 for sample pictures). 3. If corrosion is found, replace the incident tail lamp assembly(ies). * Refer to the Electronic Service Manual (ESM), section EXL-Exterior Lighting System, for tail lamp replacement. * See PARTS INFORMATION on page 3. NOTE: * Replace only the tail lamp assembly where water intrusion has been detected. * Do NOT replace the CVT assembly for this incident, if it should occur. Please see this bulleitn for further details. |
| NTB13088A | 2021-05-10. Service bulletin. SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail. |
| NTB15076 | 2021-05-10. Service bulletin. SERVICE INFORMATION When performing diagnosis on an applied vehicle with CONSULT-III plus (C-III plus) and opening Diagnosis (All Systems), four Around ViewTM Monitor (AVM) related DTCs may show as "CURRENT". These DTCs are: - U111A Rear Camera Image Signal - U111B Side Camera RH Image Signal - U111C Front Camera Image Signal - U111D Side Camera LH Image Signal See this bulletin for further detail. |