WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Nissan Altima

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

188 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Equipment and accessories are shown. Show all

Bulletins, newest first
NTB20-046b2020-09-11. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM:WIRING:SWITCHES/KNOBS/BUTTONS. VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-046a2020-08-09. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-0462020-07-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. 2019-2020 ALTIMA; VOLUME KNOB DOES NOT FUNCTION PROPERLY IF YOU CONFIRM The customer states the speaker volume does not change or changes erratically when rotating the volume knob. ACTION 1. Rotate the volume knob rapidly two times, for a total of 60-seconds, to remove contaminate build-up. 2. Update the display control unit software.
NTB19-067c2020-07-10. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT. SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049t2020-03-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-045b2020-02-08. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MIL ON WITH DTC P0087, P0101, P0448, OR P2008, VEHICLES REGISTERED OUTSIDE OF CALIFORNIA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-1002019-12-06. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; EQUIPMENT ADAPTIVE/MOBILITY. 2019-2020 ALTIMA; FOAM OUT OF POSITION AND VISIBLE AT LEADING EDGE OF INSTRUMENT PANEL IF YOU CONFIRM There is foam out of position and visible between the leading edge of the instrument panel and the bottom of the windshield (Figure 1 shows foam out of position as viewed from outside the vehicle on the passenger side). ACTION Remove the foam following the SERVICE PROCEDURE on the next page.
Expiraton Notifi2019-12-06. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING. VCR Engine Inspection – Expiration Notice UPDATE November 11, 2019 Please discard earlier versions of this bulletin. Nissan announced the following quality action in July 2019. Service Comm will de-active PC707 on any unrepaired VINs on November 15, 2019. Please inspect and, if necessary, remedy any vehicles with an open campaign prior to November 15, 2019.
PC707 2019-20 Al2019-08-12. Service bulletin. EQUIPMENT; ENGINE. VCR Engine Inspection *****Dealer Announcement***** Nissan is conducting a quality action on 356 specific MY 2019-20 Altima (L34) vehicles identified in Service Comm, to remove and inspect the lower engine oil pan. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC707 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, sell or trade the specific 2019-2020 Altima vehicles in Dealer Inventory subject to this Quality Action. 3. Use the attached procedure to inspect the vehicle. - If no gold colored debris is found in the lower engine oil pan, reseal the oil pan per the Electronic Service Manual (ESM). - File a claim for the inspection, and release the vehicle for sale - If gold colored debris is found in the lower engine oil pan, provide the requested information in an email to nnafqasupport@nissan-usa.com and HOLD the vehicle. - Do not file a claim Nissan Field Quality will review the E-mail submissions within two (2) business days of receipt and provide further instruction.
NTB19-0452019-07-22. Service bulletin. EQUIPMENT. MIL ON WITH DTC P0087, P0101, P0448, OR P2008 IF YOU CONFIRM An applied vehicle has a stored DTC shown in Table A on the next page, AND The ECM part number is shown in Table B, starting on page 3. ACTION First, perform the appropriate diagnostic procedure for the stored code to repair the vehicle according to the Electronic Service Manual (ESM), AND Reprogram the ECM after performing the diagnosis and repair.
NTB15-049s2019-07-22. Service bulletin. EQUIPMENT. TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-0412019-06-24. Service bulletin. EQUIPMENT. 2019 ALTIMA; CREAK OR POP NOISE WHEN TURNING AND ACCELERATING OR DECELERATING This bulletin applies to vehicles equipped with a 2.5L (PR25DD) engine ONLY. IF YOU CONFIRM A creak or pop noise is heard from the front of the vehicle when turning right while accelerating or decelerating. ACTION Replace the engine mounting insulator (LH) with the one listed in the PARTS INFORMATION. - For the procedure to replace the engine mounting insulator (LH) refer to the Electronic Service Manual (ESM): section REPAIR > ENGINE > ENGINE MECHANICAL > REMOVAL AND INSTALLATION > ENGINE MOUNTING INSULATOR (LH)
NTB19-0292019-05-20. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. INTELLIGENT KEY DOES NOT WORK AFTER BATTERY REPLACEMENT SERVICE INFORMATION If the Intelligent Key of an APPLIED VEHICLE does not work after replacing the battery, inspect the positive (+) terminals. If the battery side of the Intelligent Key is held by pinching down on the terminals while removing the battery, it is possible to bend the terminals down far enough that they will not touch the contacts on the other half of the Intelligent Key. If the terminals are found to be bent down, pry them back up so that they will come in contact with the other half of the Intelligent Key?s contacts. - Refer to the photos on the following pages.
PC692 - 2019 Alt2019-04-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE. Fuel Pump Dealer Inventory This bulletin applies only to vehicles equipped with Front Wheel Drive (FWD). *****Detailed Information***** Nissan is conducting a quality action to inspect and, if necessary, tighten the fuel pump lock ring on one hundred eleven (111) specific 2019 Altima (L34) FWD only vehicles identified in Service Comm. In rare occurrences, the lock ring may be completely disengaged which may require the fuel pump module and seal to be replaced. Due to a supplier issue that has since been corrected, it is possible that the fuel pump module?s lock ring is not fully engaged. If partially locked, it is possible for the fuel pump module?s lock ring to rotate to an unlocked position due to vibration during normal driving conditions. This condition may result in MIL illumination, fuel smell, and/or a rattle noise associated with the fuel pump module plastic flange. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History ? Open Campaign I.D. PC692 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability.
NTB12-103g2019-04-15. Service bulletin. POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-100b2019-04-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; POWER TRAIN. CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-0082019-02-19. Service bulletin. EQUIPMENT. NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D SERVICE INFORMATION When key registration is unsuccessful after BCM replacement, P161D (Immobilizer) will set when the ignition is turned on. Possible causes - Improper key registration - Defective BCM (Vehicles with Intelligent Key only) - EPS control unit (Vehicles with mechanical key only) - Intelligent Key unit (Vehicles with mechanical key only) Trouble Diagnosis NOTE: If DTC B2196-52 is stored with P161D, perform the diagnosis procedure for DTC B2196-52 first. - Before replacing the BCM, confirm that the keys were programmed correctly by ensuring the vehicle will start and that the lock/unlock buttons function normally. - If any keys do not function normally, re-register all of the keys. - After re-registering all of the keys, reconfirm each key's function. - If OK, erase the code to complete the repair. - If NG, diagnose the Key, BCM and/or EPS control unit per the ESM.
NTB15-049r2019-02-19. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM:SOFTWARE. TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PC669 2019 Altim2019-01-07. Service bulletin. EQUIPMENT; FUEL SYSTEM, GASOLINE. Fuel Feeder Tube Clip Dealer Inventory *****Dealer Announcement***** Nissan is issuing a quality hold to require dealers to inspect the Fuel Feeder Tube Clip position and confirm it is in the lock position on ~15,800 specific 2019 Altima vehicles identified in Service Comm. The clips may not be fully locked into place. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Dealers must complete this inspection and if necessary, repair, prior to sale. The inspection and if necessary, repair; will take less than 15 minutes per vehicle to complete and no parts are required. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC669 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Dealers should inspect the Fuel Feeder Tube Clip position to confirm it is in the locked position. 3. Use the attached procedure to inspect any vehicles affected by this quality action: - If inspection result is ?OK?, dealers may submit a warranty claim using Op Code PC6690 and release the vehicle. - If the inspection result is ?NG? (clip is not fully locked into place) - Take a photograph of the clip position and email it to: nnafqasupport@nissan-usa.com along with the following: - E-mail subject line: PC669 (Altima Fuel Feeder Tube Clip) - Attach Clear Pictures of the clip that is not locked into place. - Dealer Name: - Dealer Code: - Dealer Address:
PC665 Automatic2019-01-07. Service bulletin. EQUIPMENT. Automatic Parts Shipment List
NTB12-103f2019-01-07. Service bulletin. POWER TRAIN; EQUIPMENT. CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074m2018-05-21. Service bulletin. EQUIPMENT; EXTERIOR LIGHTING:FOG LIGHTS. FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-018c2018-05-21. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; ENGINE AND ENGINE COOLING. MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.