WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Nissan Altima

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

188 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Fuel system are shown. Show all

Bulletins, newest first
NTB22-0262022-06-08. Service bulletin. ELECTRICAL SYSTEM:INSTRUMENT PANEL:FUEL GAUGE:FUEL LEVEL FLOAT/SENSOR/SENDING UNIT; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE; FUEL SYSTEM, DIESEL; FUEL SYSTEM, GASOLINE. SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire “Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly” (fuel pump assembly). The fuel level sensor can be replaced separately. • P0460 (FUEL LEV SEN SLOSH) • P0461 (FUEL LEVEL SENSOR) • P0462 (FUEL LEVL SEN/CIRC) • P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB17-082E2022-03-12. Service bulletin. FUEL SYSTEM, OTHER; ENGINE AND ENGINE COOLING. DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J2022-03-12. Service bulletin. FUEL SYSTEM, OTHER; ENGINE AND ENGINE COOLING. EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-0092021-02-06. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. DTC B12A3-72 FOR FUEL PUMP RELAY STUCK OPEN SERVICE INFORMATION DTC B12A3-72 (Fuel Pump Relay Stuck Open) may be stored when the IPDM monitor circuit internally sees 0V to ground at pin #46. This is caused by an internal short to ground in the IPDM or one of the IPDM fuses listed below is open. If B12A3-72 is current or reoccurs after erasing DTCs, inspect the model specific fuse first. If the fuse is not open replace the IPDM. • Altima – Fuse # 58 (page 2) • Kicks – Fuse # 54 (page 3) • Versa – Fuse # 61 (page 4) For additional IPDM diagnostic information refer to the Electronic Service Manual (ESM): Section ELECTRICAL & POWER CONTROL > POWER CONTROL SYSTEM > IPDM E/R. See model specific fuse locations starting on page 2.
NTB19-0482019-07-22. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE. 2019 ALTIMA; MIL ON WITH DTC P0087 This bulletin applies only to vehicles equipped with the 2.5L engine. IF YOU CONFIRM The Malfunction Indicator Light (MIL) is ON with Diagnostic Trouble Code (DTC) P0087 (FRP CONTROL SYSTEM) stored in the Engine Control Module (ECM), AND The fuel level indicates ¼ or less. ACTION Reprogram the ECM, if applicable.
PC692 - 2019 Alt2019-04-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE. Fuel Pump Dealer Inventory This bulletin applies only to vehicles equipped with Front Wheel Drive (FWD). *****Detailed Information***** Nissan is conducting a quality action to inspect and, if necessary, tighten the fuel pump lock ring on one hundred eleven (111) specific 2019 Altima (L34) FWD only vehicles identified in Service Comm. In rare occurrences, the lock ring may be completely disengaged which may require the fuel pump module and seal to be replaced. Due to a supplier issue that has since been corrected, it is possible that the fuel pump module?s lock ring is not fully engaged. If partially locked, it is possible for the fuel pump module?s lock ring to rotate to an unlocked position due to vibration during normal driving conditions. This condition may result in MIL illumination, fuel smell, and/or a rattle noise associated with the fuel pump module plastic flange. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History ? Open Campaign I.D. PC692 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability.
PC681 2019 Altim2019-03-18. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY. Fuel Tank Dealer Inventory *****Dealer Announcement***** Nissan is conducting a quality action to inspect the fuel tank on 80 specific 2019 Altima AWD vehicles identified in Service Comm. Due to a manufacturing issue that has since been corrected, the fuel readings may not be accurate due to the presence of a plastic slug inside the fuel tank. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan requests dealers to complete this inspection and, if necessary, remedy any affected inventory prior to sale to ensure customer satisfaction. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC681 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Dealers should use the attached procedure to identify the presence of a plastic slug in the fuel tank for any vehicle subject to this quality action. - Nissan has developed an automatic parts shipment to provide affected dealers with replacement fuel sensing unit packing for affected vehicles in dealer inventory. Parts should begin to arrive at dealers on February 13, 2019 - If no plastic slug is present, install new fuel sensing unit packing and reinstall the fuel sensing unit assembly. Once reinstalled, the vehicle may be immediately released for sale. - If a plastic slug is present, remove the plastic slug, install new fuel sensing unit packing, and reinstall the fuel sensing unit assembly.
NTB13-097g2019-02-19. Service bulletin. FUEL SYSTEM, GASOLINE. ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
PC669 2019 Altim2019-01-07. Service bulletin. EQUIPMENT; FUEL SYSTEM, GASOLINE. Fuel Feeder Tube Clip Dealer Inventory *****Dealer Announcement***** Nissan is issuing a quality hold to require dealers to inspect the Fuel Feeder Tube Clip position and confirm it is in the lock position on ~15,800 specific 2019 Altima vehicles identified in Service Comm. The clips may not be fully locked into place. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Dealers must complete this inspection and if necessary, repair, prior to sale. The inspection and if necessary, repair; will take less than 15 minutes per vehicle to complete and no parts are required. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. PC669 - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Dealers should inspect the Fuel Feeder Tube Clip position to confirm it is in the locked position. 3. Use the attached procedure to inspect any vehicles affected by this quality action: - If inspection result is ?OK?, dealers may submit a warranty claim using Op Code PC6690 and release the vehicle. - If the inspection result is ?NG? (clip is not fully locked into place) - Take a photograph of the clip position and email it to: nnafqasupport@nissan-usa.com along with the following: - E-mail subject line: PC669 (Altima Fuel Feeder Tube Clip) - Attach Clear Pictures of the clip that is not locked into place. - Dealer Name: - Dealer Code: - Dealer Address:

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.