Service bulletins for the 2023 Mercedes-Benz AMG GT
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
185 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| LI07.61-P-070707 | 2024-06-01. Service bulletin. ENGINE; FUEL/PROPULSION SYSTEM. The customer complains of a check engine light (CEL) on. May also complain of the engine running roughly and/or a loss of power. Multiple Causes Remedy Please see the document "Remedy Instructions" in attachments. For MY19+ G63 there may be an alternate solution available. Please reference LI07.61-P-076755 before performing the steps in this LI. |
|---|---|
| LI27.60-P-077704 | 2024-05-30. Service bulletin. POWER TRAIN. DSI selection lever module cannot be switched to park position "P" - malfunction of "P" button Note: Vehicle can still be placed into park by opening driver's door, or turning off ignition. Please refer to operator's manual section, "Engaging park position P," for additional instructions. Possible causes: 1. Contamination/ingress of dust 2. Short circuit due to ingress of water Clean printed circuit board under plastic housing and button "P": 1. Remove DSI (AR27.60-P-0901FRX) 2. Remove housing of DSI (see picture 1) 3. Remove cover around "P" button above printed circuit board (see picture 2) 4. Check printed circuit board: Liquid residues and/or contamination (cf. picture 3) 5. Check "P" button: Water residues and/or contamination (cf. picture 4) 6. Carefully clean the affected areas (using contact cleaner) 7. Reassemble and check the functionality 8. If fault code still present after rework -- open TIPS Case (send to Body/Chassis/Entertainment Inbox) |
| OTA - 20240503 | 2024-05-30. Over-the-air update. ELECTRICAL SYSTEM. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class, CLA, EQB, EQE, EQS, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (118, 167, 192, 206, 223, 232, 243, 247, 254, 290, 294, 295, 296 and 297 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for a better entertainment experience. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update. |
| NCU - 2024040001 | 2024-05-29. Service campaign. WHEELS. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2023-2024 C-Class, CLE, E-Class, EQE, EQS, GLC, GLE, GLS, GT, S-Class, and SL vehicles (205, 206, 236, 213, 214, 238, 294, 295, 296, 297, 253, 167, 290, 223, 232 platform), the tire sealant bottle may not meet specifications. The possibility exists that the tire sealant bottle may leak within the installation location. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk. |
| LI27.60-P-077704 | 2024-05-01. Service bulletin. POWER TRAIN. DSI selection lever module cannot be switched to park position "P" - malfunction of "P" button Note: Vehicle can still be placed into park by opening driver's door, or turning off ignition. Please refer to operator's manual section, "Engaging park position P," for additional instructions. Possible causes: 1. Contamination/ingress of dust 2. Short circuit due to ingress of water Clean printed circuit board under plastic housing and button "P": 1. Remove DSI (AR27.60-P-0901FRX) 2. Remove housing of DSI (see picture 1) 3. Remove cover around "P" button above printed circuit board (see picture 2) 4. Check printed circuit board: Liquid residues and/or contamination (cf. picture 3) 5. Check "P" button: Water residues and/or contamination (cf. picture 4) 6. Carefully clean the affected areas (using contact cleaner) 7. Reassemble and check the functionality 8. If fault code still present after rework -- open TIPS Case |
| OTA - 20240402 | 2024-05-01. Service bulletin. ELECTRICAL SYSTEM. This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update. |
| LI00.20-P-077615 | 2024-04-05. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM. The following symptoms may be present in the instrument cluster: 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. Routine change in software in instrument cluster N133/1. Vehicle handover has not taken place. First manually commission the already installed instrument cluster control unit N133/1 and then perform the special procedure to re-initialize ASSYST data in powertrain control unit N127. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way. |
| OTA-24240201 | 2024-03-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update. |
| CL-CommMod | 2024-02-06. Service bulletin. ELECTRICAL SYSTEM. Dear Mercedes-Benz Owner: On behalf of Mercedes-Benz USA, LLC (MBUSA), thank you for being a part of the Mercedes-Benz family. We hope that you’re enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Communication Module software on certain Model Year 2020-2023 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, and S-Class vehicles. This update will improve the system stability and allow for better accessibility of Mercedes me services. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active “Mercedes me connect” subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle. |
| LI46.10-P-077314 | 2024-02-01. Service bulletin. STEERING. Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim! |
| LI46.10-P-077313 | 2024-02-01. Service bulletin. STEERING. The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgeräusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgeräusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgeräusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution. |
| EW-EngineThermSW | 2024-01-03. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the engine thermostat (including software update) installed in certain Model Year ("MY") vehicles (with engines M176, M177, M178) listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first), due to the following condition: In the affected vehicles, the sealing ring in the engine thermostat could detach, causing a delay in the heating of the engine coolant. This may also cause the check engine Malfunction Indicator Lamp ("MIL") to illuminate. Please follow the work instructions added to this NCU to remedy the issue. Please be advised that all repairs being claimed under this extended warranty must have a quick test uploaded with the following fault code information and may be audited. P012800 - Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 20102 - Insert, coolant thermostat o 52 - Does not operate correctly o 41 - Hard closing 20103 - Housing/cover, coolant thermostat o 73 - Electrical fault 2030T - Heating element, coolant thermostat o 53 - Insufficient effect/power o 73 - Electrical fault |
| OTA-Head Unit SW | 2024-01-03. Service bulletin. ELECTRICAL SYSTEM. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update. |
| OTA-Comm Mod SW | 2024-01-03. Service bulletin. ELECTRICAL SYSTEM. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update. |
| NCU-2023110010 | 2024-01-03. Service bulletin. ELECTRICAL SYSTEM. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY22-24 C-Class, AMG GT, AMG SL (206, 192, 232 platform) vehicles, the electric engine mount control unit software does not correspond to the latest series production configuration. In this case, a short circuit may be incorrectly detected, and the engine mounts can de-energize. This in turn could lead to changes in the vehicle’s dynamics and noise complaints from the customer. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the electric engine mount control unit software. |
| LI91.18-P-077075 | 2024-01-03. Service bulletin. SEATS. Crease formation on genuine leather seat covers in vehicles with low mileage • Objects left on the seats for extended periods of time (pressure marks). • Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). • Light initial creases due to vehicle handling. • Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material! |
| LI77.25-P-073749 | 2023-11-02. Service bulletin. STRUCTURE. Rear spoiler sporadically remains in opened position or does not extend and a fault message appears in the instrument cluster. The rear spoiler can then no longer be retracted manually using the button. The function of the rear spoiler is re-established after an ignition reset and the fault message is no longer present in the instrument cluster. Possible causes: • Coding of the AMG DRIVE UNIT for recognition of Hall sensor when retracting rear spoiler. • Hardware tolerances / hardware wear If new software for the AMG DRIVE UNIT is available, carry out the software update. If the vehicle already has the most current version of the AMG DRIVE UNIT software installed, conduct SCN coding of the AMG DRIVE UNIT. Then check the currently learned actual values under the path "DRVU -> Actual values -> Rear wing sensor system" (print AV screen prior to completing initialization -- if necessary): |
| LI77.25-P-073749 | 2023-11-02. Service bulletin. STRUCTURE. Rear spoiler sporadically remains in opened position or does not extend and a fault message appears in the instrument cluster. The rear spoiler can then no longer be retracted manually using the button. The function of the rear spoiler is re-established after an ignition reset and the fault message is no longer present in the instrument cluster. Possible causes: • Coding of the AMG DRIVE UNIT for recognition of Hall sensor when retracting rear spoiler. • Hardware tolerances / hardware wear If new software for the AMG DRIVE UNIT is available, carry out the software update. If the vehicle already has the most current version of the AMG DRIVE UNIT software installed, conduct SCN coding of the AMG DRIVE UNIT. Then check the currently learned actual values under the path "DRVU -> Actual values -> Rear wing sensor system" (print AV screen prior to completing initialization): |
| NCU-HU SW Update | 2023-09-01. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customer’s vehicle. The OTA may be validated as successful on the customer’s Mercedes Me connect app under “Over-the-Air Vehicle Updates” as “Update for the communication module”. If the OTA is successful it will show a green “installed” and date of installation in the Over-the-Air update section. |
| LI42.15-P-076805 | 2023-09-01. Service bulletin. SERVICE BRAKES, HYDRAULIC. Brake squeal on rear axle, usually when braking slowly. Frictional vibrations. Note: there is no adverse effect to braking capability Install new brake linings with part number A 000 420 38 03. |
| LI77.25-P-073749 | 2023-08-02. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE. Rear spoiler sporadically remains in opened position or does not extend and a fault message appears in the instrument cluster. The rear spoiler can then no longer be retracted manually using the button. The function of the rear spoiler is re-established after an ignition reset and the fault message is no longer present in the instrument cluster. Possible causes: • Coding of the AMG DRIVE UNIT for recognition of Hall sensor when retracting rear spoiler. • Hardware tolerances / hardware wear If new software for the AMG DRIVE UNIT is available, carry out the software update. If the vehicle already has the most current version of the AMG DRIVE UNIT software installed, conduct SCN coding of the AMG DRIVE UNIT. Then check the currently learned actual values under the path "DRVU -> Actual values -> Rear wing sensor system" (print AV screen prior to completing initialization -- if necessary): If the values are all within the target range (green): --> Subject the vehicle to a final inspection/test drive and, if the findings report is OK, return it to the customer. If the values are not within the target range (red): --> Re-initialize the rear spoiler (if necessary up to 5x) until all values are in the target area (green). |
| LI82.85-P-075375 | 2023-07-03. Service bulletin. COMMUNICATION:MANUFACTURER TELEMATICS; EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE; ELECTRICAL SYSTEM; UNKNOWN OR OTHER. In the MBUX weather app, the temperature is displayed in the wrong unit (Fahrenheit instead of °C, or vice versa). Temperature setting in Mmc mobile application settings incorrect Remedy Adjust the setting in the Mercedes me connect app via mobile phone (settings -> units) |
| LI88.20-P-071570 | 2023-06-05. Service bulletin. STRUCTURE; EXTERIOR LIGHTING. Complaint Bulging of front bumper above headlamps (see attachment). Function of headlights not blocked or impaired. Cause Bonding between bracket and bumper may be separating. |
| LI46.15-P-071669 | 2023-04-05. Service bulletin. STEERING. Complaint Loads induced at the steering wheel through pushing and pulling actions may cause creaking and cracking noises in the mechanical steering column. Cause Insufficient grease lubrication in the clamping area of the mechanical steering column. Remedy Grease the clamping area. |
| LI72.20-P-075746 | 2023-02-03. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES. Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.