Service bulletin LI46.15-P-071669
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10233783 |
| Published by NHTSA | 2023-04-05 |
| Manufacturer's number | LI46.15-P-071669 |
| Manufacturer's date | 2023-03-01 |
| NHTSA component | STEERING |
NHTSA's summary
Complaint Loads induced at the steering wheel through pushing and pulling actions may cause creaking and cracking noises in the mechanical steering column. Cause Insufficient grease lubrication in the clamping area of the mechanical steering column. Remedy Grease the clamping area.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Steering
| MERCEDES BENZ C 300 4MATIC | 2018 |
|---|---|
| MERCEDES-BENZ AMG C43 | 2016 to 2022 |
| MERCEDES-BENZ AMG C63 | 2015 to 2021 |
| MERCEDES-BENZ AMG C63 S | 2019 to 2022 |
| MERCEDES-BENZ AMG C63S | 2015 to 2018 |
| MERCEDES-BENZ AMG CLS53 | 2019 to 2021 |
| MERCEDES-BENZ AMG E43 | 2017 to 2018 |
| MERCEDES-BENZ AMG E53 | 2019 to 2023 |
| MERCEDES-BENZ AMG E53 S | 2021 |
| MERCEDES-BENZ AMG E63 | 2018 to 2022 |
| MERCEDES-BENZ AMG E63 S | 2023 |
| MERCEDES-BENZ AMG E63S | 2018 to 2022 |
| MERCEDES-BENZ AMG GT 63 | 2019, 2020 (the catalog's model; the bulletin names a series or trim of it) |
| MERCEDES-BENZ AMG GT43 | 2020, 2021, 2022, 2023 (the catalog's model; the bulletin names a series or trim of it) |
| MERCEDES-BENZ AMG GT53 | 2019, 2020, 2021, 2022, 2023 (the catalog's model; the bulletin names a series or trim of it) |
| MERCEDES-BENZ AMG GT63 | 2019, 2020, 2021, 2022, 2023 (the catalog's model; the bulletin names a series or trim of it) |
| MERCEDES-BENZ AMG GT63 S | 2022, 2023 (the catalog's model; the bulletin names a series or trim of it) |
| MERCEDES-BENZ AMG GT63S | 2019, 2020, 2021 (the catalog's model; the bulletin names a series or trim of it) |
| MERCEDES-BENZ C 300 | 2017 to 2022 |
| MERCEDES-BENZ C 350 | 2020 |
| MERCEDES-BENZ C 350 E | 2018 to 2020 |
| MERCEDES-BENZ C300 | 2015 to 2016 |
| MERCEDES-BENZ C350 | 2015 to 2017 |
| MERCEDES-BENZ C350E | 2016 to 2017 |
| MERCEDES-BENZ C400 | 2015 |
| MERCEDES-BENZ C450 | 2016 to 2017 |
| MERCEDES-BENZ CLS 450 | 2019 to 2023 |
| MERCEDES-BENZ E 300 | 2018 to 2019 |
| MERCEDES-BENZ E 350 | 2020 to 2023 |
| MERCEDES-BENZ E 350 E | 2021 |
| MERCEDES-BENZ E 400 | 2018 |
| MERCEDES-BENZ E 450 | 2019 to 2023 |
| MERCEDES-BENZ E300 | 2017 |
| MERCEDES-BENZ E350 | 2017 |
| MERCEDES-BENZ E400 | 2017 |
| MERCEDES-BENZ E43 AMG | 2018 |
| MERCEDES-BENZ E550 | 2017 |
| MERCEDES-BENZ E63 | 2019 |
| MERCEDES-BENZ E63 AMG | 2020 |
| MERCEDES-BENZ E63S | 2018 to 2019 |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 22V189000 | 2022-03-25. STEERING: STEERING WHEEL/HANDLE BAR |
|---|
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| LI46.10-P-080896 | 2026-10-06. Service bulletin. Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves. |
|---|---|
| LI46.10-P-077314 | 2026-10-06. Service bulletin. Complaint Noises in the steering column area when steering. See example file in the attachments area: "MRSM‑Schleifgeräusch_SCCMGrindingNoises. MOV". Cause Under analysis. Remedy Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: ‑ Loosen screws of the MRSM/SCCM and steering wheel, re‑align the MRSM/SCCM, and re‑fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. ‑ If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. ‑ If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. ‑ If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: ‑ When installing the MRSM/SCCM, make sure that no damage occurs! ‑ If the noise is due to the steering wheel (see attachment "Lenkrad‑Schleifgeräusch_SteeringWheel‑GrindingNoises.mp4"), please use LI46.10‑P‑077313. ‑ Only disassemble and mount all component parts in the "straight‑ahead position" (see also WIS). ‑ Please refer to this LI in the "Notes" section of the warranty claim! |
| LI46.35-P-067339 | 2026-09-09. Service bulletin. Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty! |
| LI46.10-P-078012 | 2026-07-21. Service bulletin. Complaint Hand detection system – malfunction / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" "Active steering assist not available" Cause Possible causes: Hand detection mat, hand detection control unit, contacts, and electrical feed line. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Check: Please do not replace the HOSWD control unit. Please flash the new SW and perform the SCN coding for the HOSWD control unit (N179/1) (available from July 2026). The software can be flashed onto all HOSWD213 with HW number A0009011522 and all HOSWD223 with HW number A0009011422. Please also flash the SW for the IDC control unit (N62/4), if possible (only applies to HOSWD223). Erase fault memory Remedy: Turn on the ignition or start the engine without touching the steering wheel. If, after 10 seconds without touching the steering wheel, one of the three fault messages appears on the instrument cluster: Check the contacts and feed lines in the steering wheel by means of a visual inspection for damage, crimp connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace the steering wheel electronics or the feed lines. If there is not any visible damage -> replace the steering wheel rim. If a yellow message does not appear on the instrument cluster within 10 seconds: Grasp the steering wheel fully with both hands, including the chrome molding at the 6 o'clock position (see picture 1). If the fault is triggered by grasping the steering wheel rim or pressing the clip at the 6 o'clock position, check the contacts and feed lines in the steering wheel by means of a visual inspection for damage, kinked connections, loose connections, etc. (example in picture 2 and 3). Check the ground connections (screw connections and cables to the steering wheel rim); if necessary, retighten the screws/bolts and check for corrosion (picture 4). If there is visible damage -> replace the steering wheel electronics or the feed lines. If there is not any visible damage: Replace the steering wheel rim. Please do not replace the HOSWD control unit. A TIPS case should be created if fault profile is unclear. In the event of a customer complaint and a further fault code in HOSWD: B1E7713: Check the ground connections (screw connections and cables to the steering wheel rim); if necessary, retighten the screws/bolts and check for corrosion (picture 4). B1F1F04: Check the control unit of the hand detection system; if necessary, replace this with the control unit from a donor vehicle (make sure that the hardware part numbers are identical). |
| LI46.15-P-063353 | 2025-06-26. Service bulletin. Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function), noise (breakaway noise) when leaving the limit stops of the height adjustment. Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Driver seat control unit software 2. Steering column height adjustment transmission Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Perform software update of driver's seat control unit 2. Replace repair kit for steering column height adjustment Procedure 1: Perform software update of driver seat control unit. ALL models except 205/253/293/222/217/231/463/213/238/257/290 up to special equipment code 801. • Move out the fore/aft adjustment to the end position. • Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward • After releasing the jam, perform a software update of the driver's seat control unit If procedure 1 is not effective, there is no new software available for the driver seat control unit, or the chassis is not listed above (167, 223, 294, 206, 294, 295, 296, 297,232,214,254) then use procedure 2. Procedure 2: Replace repair kit for steering column height adjustment. • Move out the fore/aft adjustment to the end position. • Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel/at the same time pressing adjustment switch downward • Remove footwell trim on driver's side. • Determine type version of height adjustment in XENTRY Parts Information and order appropriate replacement part (refer to attachment). 1. Version A: A 231 460 77 00 2. Version B: A 205 460 38 03 • Remove steering column. • Remove height adjustment (adjustment repair kit). • Install repair kit (adjustment repair kit) (observe tightening torque for screws in attachment). • Install steering column. • If possible, flash driver seat control unit to latest software release or code SCN again. • Commission driver seat control unit (normalization of limit stops is deleted and learning process repeated). |
| LI46.80-P-078043 | 2024-07-31. Service bulletin. Complaint Message in the instrument cluster regarding rear axle steering • In the short test, the fault > Actuator blocked < appears Cause Vehicle may detect high adjustment force in the rear axle steering. Remedy Old Hardware: A 290 460 3300 / 3400 > SW A 290 902 7400 Caution! This hardware cannot be flashed with the new version. Only the current hardware with the corresponding previous software release can be flashed. If the vehicle still has the old hardware installed, do not attempt to flash; instead, please create a TIPS case. Current Hardware: A 290 460 3900 / 4000 >> SW A 290 902 5101 This hardware can be flashed with A 290 902 1005. Flash control unit N68/3 and N68/4 with current software release A 290 902 1005 using XD. |
| LI46.10-P-077314 | 2024-02-01. Service bulletin. Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim! |
| LI46.10-P-077313 | 2024-02-01. Service bulletin. The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgeräusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgeräusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgeräusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution. |
| LI46.15-P-063353 | 2023-01-05. Service bulletin. Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. |
| LI46.15-P-063353 | 2022-10-05. Service bulletin. Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit |