WenmarOpen by Wenmar Pro

Service bulletins for the 2023 Mercedes-Benz AMG GT

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

185 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
LI54.21-P-0803262026-10-02. Service bulletin. ELECTRICAL SYSTEM. Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2‑ 3 key cycles. The vehicle can be released back to the customer.
LI54.21-P-0803262026-07-24. Service bulletin. ELECTRICAL SYSTEM. Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.
LI00.20-P-0776152026-07-06. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. The following applies to model series 167 from AEJ 22/1 onward, 192 AMG, 206, 214, 223, 232 AMG, 236, 254, 290 AMG from AEJ 23 onward, 294, 295, 296, 297 and 465: Reinitialize ASSYST Plus under Adaptations – Teach-in processes – ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.
LI54.21-P-0803262026-07-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy 167: SW has been released. Update the FSAM to the latest SW version. 465, 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.
LI00.20-P-0807032026-06-16. Service bulletin. ELECTRICAL SYSTEM. Complaint Service code B1 displayed in the customer menu does not match the workshop code displayed in the workshop menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.
LI00.20-P-0776152026-06-16. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations – Teach-in processes – ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.
LI00.20-P-0776152026-06-02. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations – Teach-in processes – ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.
LI54.71-P-0791042026-04-10. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q2 2026.
LI82.85-P-0787222026-03-17. Service bulletin. ELECTRICAL SYSTEM. Complaint The vehicle's position on the map is displayed far away from its actual position, e.g. the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.
LI54.65-P-0801322026-03-17. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.
NCU - 20251200092026-03-14. Service campaign. ELECTRICAL SYSTEM; POWER TRAIN. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the drivetrain control unit does not meet current production specifications. The system may experience an excessively high quiescent current draw on the vehicle, which could lead to an increased discharge of the 12V battery. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the drivetrain control unit software.
LI54.10-P-0731642026-03-10. Service bulletin. ELECTRICAL SYSTEM. Complaint Yellow information message in driver display (instrument cluster): "Switch on motor to charge the 12V battery" Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: • If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% – a negative charge balance • A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. • An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use.
LI54.10-P-0696982026-02-28. Service bulletin. ELECTRICAL SYSTEM. Complaint This LI does Not apply to 223 or 206 which use a different generation of 48V systems. Please follow the relevant guided tests for the 223 and 206. For 223 with fault code B1FCB97 follow LI54.10-P-076026. Various causes are possible. The faults listed in the various causes do not all have to be present at all times. Some of these complaints may overlap. Rely on the faults listed in the Cause section for identifying the correct Remedy. 1. No start 2. Yellow or red instrument cluster message for 48 V on-board electrical system battery (G1/3) 3. Limp home mode, overheating, A/C not blowing cold, or loss of acceleration 4. Check Engine Light Cause Cause 1: Software causes Intermittent No Starts with fault B183387 in DC/DC converter N83/1 Cause 2: Software causes Permanent No Start with fault B183349. May also have fault B183371. Cause 3: Hardware short circuit in 48V system causes fault B183319 in 48V battery. May also have fault B183371. Cause 4: Internal 48V battery Peltier cooling element failure causes fault B183397 Cause 5: This will Always have fault code B183371 but different from cause 2 and 3 -- it will Not have B183349, B183319, or any other faults in the 48V battery. This will only have fault B183371 in 48V battery. Cause 5 is from the 48V battery detecting an abnormality which then causes the 48V battery to disconnect itself. The disconnected 48V battery then causes subsequent symptoms: Limp Home Mode, overheating, A/C not blowing cold, or loss of acceleration Cause 6: Check Engine Light with fault P0606F1 in the N127 PTCU Cause 7: Check Engine Light with possible no start and fault P057FF1 Remedy Note: each of these remedies correspond to a specific cause. Make sure to match correct Cause with Remedy. Remedy 1: 1. Check the 12V power supply and LIN connection 2. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 3. Road test and release vehicle if no further symptoms Remedy 2: 1. Charge the 12V battery (Charging current <5A) 2. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 3. Road test and release vehicle if no further symptoms If the faults return or cannot be cleared: 1. XENTRY MUST be connected with VCI cable to correctly complete this remedy. 2. Complete guided test for B183349. 3. If guided test completes, vehicle starts, and drive cycles show no further symptoms, release vehicle. 4. If after guided test completes, XENTRY states to replace 48V battery: replace only 48V battery. If vehicle is a MY21 w/M256 engine, update SW in 48V battery 5. If this is a repeat visit for fault B183349 and guided test has already been completed, open a TIPS case. 6. If guided test does not complete OR symptoms are still present open a TIPS case. 7. If communication cannot be established with 48V battery perform physical layer check at 12V wiring to DCDC. If no abnormalities found, replace the 48V battery. 8. If guided test completes but a new fault code is present (such as B183319, B183371, etc.) follow the relevant Cause/Remedy for that fault in this LI. Remedy for 3: (If this occurred after Campaign 2025050001, this Li does not apply and LI54.10-P-079772 should be followed) 1. If fault is not Current (only Stored): 1. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 2. Road test and release vehicle if no further symptoms If the faults return or this is a second visit after the SW update: 1. Complete the guided test for B183319 2. Perform XENTRY actuations for all 48V components. 3. Create a TIPS case with ALL Preliminary measures required as noted below for Remedy 5 4. Upload to TIPS case ISA performance data from the N129. 5. ISA performance data location in XD: 6. N129 control unit under Special Procedures 7. "Procedures for support queries to market support" 8. "Collation of diagnosis performance data" 9. "engine at idle" See attachment for further instructions.
LI27.19-P-0802192026-02-17. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Complaint Check engine light on with the following fault is current in the VGS Control Unit: P084300 Oil pressure sensor 'A' has a short circuit to positive stored in VGS control unit. Cause Electrical failure of oil pressure sensor integrated into VGS Control Unit Remedy Intelligent Predictive Repair (IPR) recognizes this fault pattern and will provide the necessary repair suggestion. 1. Perform IPR and follow the recommended procedures 2. Replace complete EHS valve body, fill to near max fluid level, & complete initial start-up - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement.
NCU - 20240900072026-02-13. Service campaign. ELECTRICAL SYSTEM; ENGINE. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.
LI54.71-P-0802362026-02-06. Service bulletin. ELECTRICAL SYSTEM. Complaint Red ring displayed around vehicle when front or rear camera door actuates. Please also see LI54.65-P-080132 for additional listed red ring causes. Cause EMF interference. Remedy Camera functionality is not affected. Cameras and displays operate normally. For vehicles with a front facing actuating camera and flap (223 and 297): • 223, 297 > Install clip on ferrite magnet on M35/1, pin 3. For vehicles with rear facing camera (223, 213 Facelift, 238, 257, 290, 297): • 297 > Install 2 x ferrite magnets on M35/2, pin 3 and 4. • 213 Facelift, 223, 238, 257, 290 > Install on M35/2, pin 4
LI82.85-P-0787222026-01-27. Service bulletin. ELECTRICAL SYSTEM. Complaint The vehicle's position on the map is displayed far away from its actual position, e.g. the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.
LI54.30-P-0800902025-12-09. Service bulletin. ELECTRICAL SYSTEM. Complaint The Head-up display (HUD) may be perceived as too bright and without adjustment. Cause Signal from the rain/light sensor is not recognized/processed correctly. As a result, the HUD is permanently displayed at maximum brightness. The customer has the option to turn off the HUD via MBUX. Remedy Software update of the "Head-up display" control unit.
LI54.10-P-0800532025-12-04. Service bulletin. ELECTRICAL SYSTEM. Complaint Discharge of 12 V battery in the event of a longer non-operational time - model series 232 and model series 192 Cause Increased quiescent current Remedy 1. Conduct quiescent current measurement. DO NOT USE A DVOM IN LINE - this will blow the fuse in your meter. Use an amp clamp with either a DVOM or XENTRY Scope and wait until the vehicle has gone to sleep (usually takes 6-10 minutes). Once the vehicle is asleep, observe the quiescent current for 10-15 minutes and note down the values. A stable quiescent current should be less than 50 mA. Values higher than this figure are considered not OK (NOK) and require further analysis. 2. If the quiescent current is higher (> 50 to 100 mA): • Check whether software updates are available for relevant control units: Door control units (DMD (N69/1), DMP (N69/2), DMRL (N69/3), DMRR (N69/4)), EIS (N73/3), PTCU (N127), OHCM (N70), GW (N73/3*1) • After installing the updates: measure the quiescent current again • If the quiescent current is < 50 mA, the vehicle is OK • If the quiescent current is between 50 and 100 mA, continue with step 5 • If the quiescent current is between 100 and 200 mA, continue with step 3 • If the quiescent current is between 200 mA and 1 A, continue with step 4 3. For no-load current values of 100 to 200 mA: • Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. • Disconnect door separation points (A-pillar connection) when the vehicle is asleep, starting with the driver's side • Document the quiescent current value • If there is no change: Disconnect the door separation point on the front passenger side and note down the value again • If the quiescent current falls below 50 mA after the door separation point is opened, the respective outer door handle must be replaced • If the quiescent current remains low after the relevant door handles have been successfully replaced, please create a TIPS case to the LV/HV inbox and retain the removed door handles for the time being • If the quiescent current does not change after the door separation point is opened, please carry out step 5 4. For quiescent current values between 200 mA and 1 A: • Important: Before pulling out F320 and F304, the tow-away protection and interior protection must be deactivated to prevent an alarm from triggering • Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. • Wait until the vehicle has gone to sleep • Pull out the fuses one after the other, starting with F323 (PTCU CU/N127), and note down the quiescent current value • Perform the same test one at a time if the value is still high for each additional fuse: F119 (PTCU CU/N127), F324 (EIS CU/N73/3), F305 (EIS CU/N73/3), F320 (OCP CU/N70), F304 (OCP CU/N70) • If pulling out the fuse reduces the quiescent current to below 50 mA, replace the corresponding control unit. After replacing, please measure and assess the quiescent current again • Please create a TIPS case for information purposes • If the quiescent current remains unchanged after the fuses listed above are pulled out, please carry out step 5 5. If the quiescent current remains above 50 mA after all controls have been implemented: • Create a TIPS case • Document all the completed steps and measurement results • Attach the XENTRY Scope trace of the draws that you have seen and identify where certain steps were taken. • Attach the latest N73 and N73/3*1 CUL's • If the quiescent current is higher than 1 A, the bus keep awake control unit should be identified via the EIS gateway
NCU - 20240900072025-10-10. Service campaign. ELECTRICAL SYSTEM. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.
LI54.10-P-0696982025-09-22. Service bulletin. ELECTRICAL SYSTEM. See Attachment
LI54.10-P-0797722025-09-18. Service bulletin. ELECTRICAL SYSTEM. Complaint After a software update from campaign 2025050001 of component LIB48_222 - G1/3 (48 V on-board electrical system battery) from software release A 000 902 50 48 to software release A 000 902 15 89, the fault code B183319 may be output. B183319 "The battery for the 48V on-board electrical system has a malfunction. The limit value for current has been exceeded" Cause Anomaly in the software update Remedy Please perform the following steps in the specified sequence: 1.) Delete fault codes 2.) Disconnect XENTRY Diagnosis and the 12 V battery charger 3.) Disconnect ground cable from the 12 V battery 4.) Ensure bus idle for at least 10 minutes 5.) Re-connect ground cable to the 12 V battery 6.) Delete fault codes again 7.) Perform a test drive 8.) Check fault codes > If fault code B183319 is still current, continue with the guided fault analysis in XENTRY Diagnosis. > If fault code B183319 goes to stored and can be cleared, no further action is required.
NCU - 20250800072025-09-12. Service campaign. ELECTRICAL SYSTEM. Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the High Voltage Battery (“HVB”) AC charger software does not correspond to current production specifications. As a consequence, a HVB MIL may illuminate during charging due to fluctuations in power consumption of the charging socket actuator. Remedy MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the HVB AC Charger Software.
LI54.10-P-0797722025-09-12. Service bulletin. ELECTRICAL SYSTEM. Complaint After a software update of component LIB48_222 - G1/3 (48 V on-board electrical system battery) from software release A 000 902 50 48 to software release A 000 902 15 89, the fault code B183319 may be output. B183319 "The battery for the 48V on-board electrical system has a malfunction. The limit value for current has been exceeded" Cause Anomaly in the software update Remedy Please perform the following steps in the specified sequence: 1.) Delete fault codes 2.) Disconnect XENTRY Diagnosis and the 12 V battery charger 3.) Disconnect ground cable from the 12 V battery 4.) Ensure bus idle for at least 10 minutes 5.) Re-connect ground cable to the 12 V battery 6.) Delete fault codes again 7.) Perform a test drive 8.) Check fault codes > If fault code B183319 is still current, continue with the guided fault analysis in XENTRY Diagnosis. > If fault code B183319 goes to stored and can be cleared, no further action is required.
OTA - 202508292025-08-28. Over-the-air update. ELECTRICAL SYSTEM. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the charging function does not correspond to the current series production configuration. The charging system software will be updated to stabilize the charging function of the vehicle. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.