WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Mazda Mazda2

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

187 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
MTI_11112017-02-11. Service bulletin. EQUIPMENT. WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES “LINKED” TO THE VIN OF THAT VEHICLE.
MTI_10342017-02-10. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:HEATER CORE. THIS ARTICLE PROVIDES HVAC HEATER/DEFROSTER OPERATING TIPS USING MODE SELECTOR DIAL. THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.
09-020-16-31832017-02-08. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXPERIENCE A FUZZY APPEARANCE (TINY CRACKS) AROUND THE EDGE OF THE ACTIVE DRIVING DISPLAY. REPLACE THE ACTIVE DRIVING DISPLAY.
02-005-16-3152A2017-02-08. Service bulletin. SUSPENSION. BEGINNING WITH THE CX-5 AND MAZDA6 MODELS, GRIP TYPE FRONT AND REAR STABILIZER BUSHINGS HAVE BEEN INCORPO-RATED FOR NOISE PREVENTION PURPOSES. IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE.
02-009-16-31552017-02-07. Service bulletin. STEERING. SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD.
1098M2017-02-07. Service bulletin. STRUCTURE. WHEN REMOVING PARTS FROM A VEHICLE, TAKE CAUTION OF THIS SYMBOL "R". FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.
1096M2017-02-07. Service bulletin. ELECTRICAL SYSTEM. IF THE ACTIVE DRIVING DISPLAY (AD-DISP) UNIT REQUIRES REMOVAL, USE CAUTION WHEN DISCONNECTING/CONNECTING THE WIRING HARNESS. IF THE HARNESS IS NOT CONNECTED PROPERLY, THE AD-DISP MAY NOT OPERATE.
SA2342016-12-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. IDS UPDATE 101.00 AND 101.02 IS NOW AVAILABLE ON MS3 UNDER THE "IDS/INFOTAINMENT" TAB.
1080M2016-12-01. Service bulletin. ENGINE. IF AN ENGINE ASSEMBLY IS REPLACED AFTER A CATASTROPHIC INTERNAL MECHANICAL FAILURE, CLEAN THE INTAKE MANIFOLD INTERNALLY BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT
MTI_11112016-11-28. Service bulletin. EQUIPMENT. WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES “LINKED” TO THE VIN OF THAT VEHICLE.
09-036/152016-07-14. Service bulletin. ELECTRICAL SYSTEM. BSM RADAR AIMING CANNOT BE PERFORMED AFTER RIGHT-SIDE BSM CONTROL MODULE REPLACEMENT. IF RIGHT-DIDE BSM CONTROL MODULE REQURES REPLACEMENT FOR ANY REPAIR, ALSO REPLACE LEFT SIDE BSM CONTROL MODULE TO COMPELTE THE RADAR AIMING PROCEDURE (IT'S OK TO REPLACE THE LEFT BSM ALONE). IF THE RIGHT-SIDE BSM CONTROL MODULE IS REPLACED ALONE, "AUTOMATIC CONFIGURATION" IS NOT PERFORMED DUE TO PROGRAM ERROR IN MODULE. BECAUSE OF THIS, THE REQUIRED "BSM RADAR AIMING" CANNOT BE PERFORMED. "AUTOMATIC CONFIGURATION" AS WELL AS "BSM RADAR AIMING" CAN BE PERFORMED IF LEFT-SIDE BSM CONTROL MODULE IS REPLACED ALONE OR TOGETHER WITH RIGHT-SIDE BSM CONTROL MODULE.
09-010/162016-07-14. Service bulletin. STRUCTURE. STAINS FOUND ON PAINT DURING PDI SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEN PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED ARE TO REMOVE STAIN(S).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.