Service bulletins for the 2024 Mazda CX-90
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
552 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| 7325C Warranty | 2025-04-02. Emissions. ENGINE. 7325C - EMISSION RECALL - 2024-2025 CX-90 AND 2025 CX-70 PHEV ONLY - HYBRID SYSTEM WARNING LIGHT MAY TURN ON. Mazda Motor Corporation has decided to conduct an Emission Recall on certain 2024-2025 CX-90 and 2025 CX-70 PHEV vehicles. Please see the description, model, year, and VIN range below for all vehicles in this campaign. There are 38,812 vehicles affected by this concern in the U.S. and U.S. Territories. Vehicles produced and sold by Mazda Canada Inc. are also included in this campaign and should be repaired if presented to your dealership following Mazda Warranty policy 3.30. STOP DELIVERY OF AFFECTED VEHICLES: MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 5,197 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired.To All Mazda Dealers: Failure to properly perform any recall repair is a direct violation of Paragraph 14(F) of the Dealer Agreement and can cause one or more of the following: Mechanical breakdown or failure, crash or injury, Dealership penalties/fines by Mazda and CARB/EPA, increased liability risk for the dealership, Missed Recall penalties, loss of customer trust and a poor Customer Experience. Concern Outline: All vehicles can be repaired immediately upon receipt of this Mazda Dealer announcement by following the repair and warranty claiming procedures housed in Mazda Global Service Support (MGSS). On certain subject vehicles, during normal driving, a temporary decrease in insulation resistance may be detected, which could be mistakenly judged as an electric leakage, causing the hybrid system warning light to turn on and the leakage detection message to be displayed. The DTC P0AA6:00 may be stored in memory. In such a condition, once the vehicle power is switched off, it may become impossible to restart the vehicle due to fail-safe mode activation. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). The DTC code that may appear is P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance. The software update will re-calibrate electrical leakage detection criteria and allow vehicle re-start. Legitimate electrical leakage faults can still be detected and store DTC P0AA6:00. If DTC P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance is still present after repair of the 7325C Recall, please diagnose the issue using the Workshop Manual or search for a current Technical Service Bulletin. |
|---|---|
| 7325C Repair | 2025-04-02. Emissions. ENGINE. 7325C - EMISSION RECALL - 2024-2025 CX-90 AND 2025 CX-70 PHEV ONLY - HYBRID SYSTEM WARNING LIGHT MAY TURN ON. Mazda Motor Corporation has decided to conduct an Emission Recall on certain 2024-2025 CX-90 and 2025 CX-70 PHEV vehicles. Please see the description, model, year, and VIN range below for all vehicles in this campaign. There are 38,812 vehicles affected by this concern in the U.S. and U.S. Territories. Vehicles produced and sold by Mazda Canada Inc. are also included in this campaign and should be repaired if presented to your dealership following Mazda Warranty policy 3.30. STOP DELIVERY OF AFFECTED VEHICLES: MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 5,197 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired.To All Mazda Dealers: Failure to properly perform any recall repair is a direct violation of Paragraph 14(F) of the Dealer Agreement and can cause one or more of the following: Mechanical breakdown or failure, crash or injury, Dealership penalties/fines by Mazda and CARB/EPA, increased liability risk for the dealership, Missed Recall penalties, loss of customer trust and a poor Customer Experience. Concern Outline: All vehicles can be repaired immediately upon receipt of this Mazda Dealer announcement by following the repair and warranty claiming procedures housed in Mazda Global Service Support (MGSS). On certain subject vehicles, during normal driving, a temporary decrease in insulation resistance may be detected, which could be mistakenly judged as an electric leakage, causing the hybrid system warning light to turn on and the leakage detection message to be displayed. The DTC P0AA6:00 may be stored in memory. In such a condition, once the vehicle power is switched off, it may become impossible to restart the vehicle due to fail-safe mode activation. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). The DTC code that may appear is P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance. The software update will re-calibrate electrical leakage detection criteria and allow vehicle re-start. Legitimate electrical leakage faults can still be detected and store DTC P0AA6:00. If DTC P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance is still present after repair of the 7325C Recall, please diagnose the issue using the Workshop Manual or search for a current Technical Service Bulletin. |
| 7325C Dealer Letter | 2025-04-02. Emissions. ENGINE. 7325C - EMISSION RECALL - 2024-2025 CX-90 AND 2025 CX-70 PHEV ONLY - HYBRID SYSTEM WARNING LIGHT MAY TURN ON. Mazda Motor Corporation has decided to conduct an Emission Recall on certain 2024-2025 CX-90 and 2025 CX-70 PHEV vehicles. Please see the description, model, year, and VIN range below for all vehicles in this campaign. There are 38,812 vehicles affected by this concern in the U.S. and U.S. Territories. Vehicles produced and sold by Mazda Canada Inc. are also included in this campaign and should be repaired if presented to your dealership following Mazda Warranty policy 3.30. STOP DELIVERY OF AFFECTED VEHICLES: MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 5,197 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired.To All Mazda Dealers: Failure to properly perform any recall repair is a direct violation of Paragraph 14(F) of the Dealer Agreement and can cause one or more of the following: Mechanical breakdown or failure, crash or injury, Dealership penalties/fines by Mazda and CARB/EPA, increased liability risk for the dealership, Missed Recall penalties, loss of customer trust and a poor Customer Experience. Concern Outline: All vehicles can be repaired immediately upon receipt of this Mazda Dealer announcement by following the repair and warranty claiming procedures housed in Mazda Global Service Support (MGSS). On certain subject vehicles, during normal driving, a temporary decrease in insulation resistance may be detected, which could be mistakenly judged as an electric leakage, causing the hybrid system warning light to turn on and the leakage detection message to be displayed. The DTC P0AA6:00 may be stored in memory. In such a condition, once the vehicle power is switched off, it may become impossible to restart the vehicle due to fail-safe mode activation. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). The DTC code that may appear is P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance. The software update will re-calibrate electrical leakage detection criteria and allow vehicle re-start. Legitimate electrical leakage faults can still be detected and store DTC P0AA6:00. If DTC P0AA6:00 - High voltage insulation malfunction: Decrease in vehicle insulation resistance is still present after repair of the 7325C Recall, please diagnose the issue using the Workshop Manual or search for a current Technical Service Bulletin. |
| MSP62 Parts and Warranty | 2025-04-02. Service campaign. SUSPENSION. MSP62 - MAZDA SERVICE PROGRAM - 2024 CX-90 - ABNORMAL NOISE FROM FRONT OF VEHICLE. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP62) for vehicles in the U.S. and U.S. Territories. Mazda vehicles sold in Canada and Mexico are also affected by MSP62 and must be repaired if presented to your dealership.MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 20 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired. Outline of Concern: Some vehicles may exhibit a creaking or squeaking noise from the lower arm at the front suspension when traveling over a bump and while turning at low-speed. Causal factor: A stick-slip phenomenon may occur between the stopper rubber and the bracket in the front lower arm. There are 18,127 vehicles affected by this campaign in the U.S. and U.S. Territories.Important Note: Certain vehicles repaired under TSB# 02-002/24 are excluded from this MSP but others may be included. If the MSP62 is Open in eMDCS Warranty Inquiry, please perform the repair. |
| MSP62 Repair | 2025-04-02. Service campaign. SUSPENSION. MSP62 - MAZDA SERVICE PROGRAM - 2024 CX-90 - ABNORMAL NOISE FROM FRONT OF VEHICLE. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP62) for vehicles in the U.S. and U.S. Territories. Mazda vehicles sold in Canada and Mexico are also affected by MSP62 and must be repaired if presented to your dealership.MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 20 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired. Outline of Concern: Some vehicles may exhibit a creaking or squeaking noise from the lower arm at the front suspension when traveling over a bump and while turning at low-speed. Causal factor: A stick-slip phenomenon may occur between the stopper rubber and the bracket in the front lower arm. There are 18,127 vehicles affected by this campaign in the U.S. and U.S. Territories.Important Note: Certain vehicles repaired under TSB# 02-002/24 are excluded from this MSP but others may be included. If the MSP62 is Open in eMDCS Warranty Inquiry, please perform the repair. |
| MSP62 Dealer Letter | 2025-04-02. Service campaign. SUSPENSION. MSP62 - MAZDA SERVICE PROGRAM - 2024 CX-90 - ABNORMAL NOISE FROM FRONT OF VEHICLE. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP62) for vehicles in the U.S. and U.S. Territories. Mazda vehicles sold in Canada and Mexico are also affected by MSP62 and must be repaired if presented to your dealership.MAZDA SALES AND SERVICE TEAMS - ACTION ITEM: There are approximately 20 vehicles in stock at U.S. Mazda dealers which must be repaired prior to delivery. All Mazda dealers must quarantine any affected new, used or CPO in-stock vehicles until the repair is completed. The affected dealer inventory list was provided to each District Service Manager with the notification of this dealer email. Once completed, the car can be delivered, and the Warranty claim can be submitted later without penalty since the car has been repaired. Outline of Concern: Some vehicles may exhibit a creaking or squeaking noise from the lower arm at the front suspension when traveling over a bump and while turning at low-speed. Causal factor: A stick-slip phenomenon may occur between the stopper rubber and the bracket in the front lower arm. There are 18,127 vehicles affected by this campaign in the U.S. and U.S. Territories.Important Note: Certain vehicles repaired under TSB# 02-002/24 are excluded from this MSP but others may be included. If the MSP62 is Open in eMDCS Warranty Inquiry, please perform the repair. |
| SA-018-25 | 2025-04-01. Service bulletin. ELECTRICAL SYSTEM. Important Note: This Service alert is intended as an early notification for upcoming software releases. Please refer to the latest dealer communications and MGSS for updated information. CX-90 MHEV Battery: Mazda is currently experiencing many backorders on MHEV Batteries (K6Y8-67-ZBXD). The issue causing most of the concerns is a cell imbalance inside the MHEV battery, which sets DTC P0DAB. The repair solution for this concern is to perform the software reflash and replace the battery as required. The cell balancing issue is resolved with a software reflash starting in November of 2023 production and this software update is part of recall 7024J - SAFETY RECALL - MULTIPLE ECU'S REPROGRAMMING. Ensure this recall is completed on every CX-90 that comes into your dealer to prevent possible MHEV cell imbalance. As a reminder, the MHEV battery is warrantied 8 years/80,000 miles to support our customers through the life of their vehicle. In terms of the MHEV Battery back-order status, as a result of significant efforts, including air-shipping hundreds of replacement batteries, we are projecting all current backorders will be filled by the last week of March 2025. CX-90 and CX-70 PHEV Electrical Leakage: Some customers have experienced an “electrical leakage fault” with DTC P0AA6 resulting in a no start condition after one key-cycle. Mazda has identified a PCM software programming issue that causes this DTC occurrence. Under current PCM logic, when P0AA6 detection occurs, the vehicle is prevented from restarting. The new software will be available in late March to reflash vehicles. This allows vehicles to be restarted if the fault is detected. Should the DTC persist, perform normal MGSS service procedures for electrical leakage diagnosis. |
| SA-017-25 | 2025-04-01. Service bulletin. ENGINE; UNKNOWN OR OTHER. Frequently Asked Questions (FAQ) |
| SA-015-25 | 2025-04-01. Service bulletin. UNKNOWN OR OTHER; STRUCTURE:BODY. Some vehicles may exhibit poor hands-free liftgate operation after a Mazda genuine trailer tow hitch accessory installation. IMPORTANT: When a Mazda genuine trailer tow hitch is installed on a vehicle equipped with hands-free liftgate function, the sensing area is reduced due to the mechanical structure of the hitch. The hands-free liftgate’s optimal sensing area below the rear bumper is shown in green boxes in the image below. Since the left side of the hitch has a 7-pin connector socket, the right side is the most ideal for hands-free operation. For safety, be extra careful performing the kicking motion around the hitch. |
| SA-002-25b | 2025-04-01. Service bulletin. UNKNOWN OR OTHER. Some customers may experience the MyMazda App Remote Climate Control and the In-Vehicle Climate Control Timer functions are inoperative after DASH_ESU software update to "H" level. |
| 09-015-25 | 2025-04-01. Service bulletin. EXTERIOR LIGHTING. Some customers may complain about a rattle or vibration noise coming from front map light surroundings when driving on a rough road. This may be caused by the bracket for the map light. Due to heat or vibrations, the fastener fixing the front map light to the bracket may deform, making the joint loose. In such case, when the vehicle bounces, the bracket may oscillate and produce a rattling noise. To eliminate that concern, non-woven fabric will be attached to the headliner. |
| 09-014-25 | 2025-04-01. Service bulletin. UNKNOWN OR OTHER. Some vehicles may exhibit sagging (1) at the front side of the rear sunshade(s) (2) or a difference in tension between the front and rear of the sunshade(s). When the rear sunshade is fully pulled up and then hooked up, the front hook's position may be lower, causing sagging on the front side of the rear sunshade. |
| 07-001-25b | 2025-04-01. Service bulletin. UNKNOWN OR OTHER. Some vehicles may exhibit check engine light turned on at engine startup, with DTC P0531:00 stored in memory. DTC P0531:00 [PCM] - Refrigerant pressure sensor No.1 system: Function malfunction This is caused by improper control logic of the PCM and the dash-electrical supply unit (Dash-ESU). To eliminate this concern, the control logic of the PCM and the Dash-ESU has been modified. |
| 02-001-25 | 2025-04-01. Service bulletin. SUSPENSION. Some vehicles may exhibit a creaking or squeaking noise from the lower control arm at the front suspension when traveling over a bump while turning at low-speed. A stick-slip phenomenon may occur between the stopper rubber (2) and the bracket (3) in the front lower arm (rear) (1). To eliminate this concern: Grease has been applied to the stopper rubber. Dust covers have been installed to the lower arm. The mounting hole size of the lower arm bracket has been modified. |
| SA-009-25 | 2025-03-05. Service bulletin. UNKNOWN OR OTHER. Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs. |
| SA-007-25 | 2025-03-05. Service bulletin. ELECTRICAL SYSTEM; UNKNOWN OR OTHER. The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. |
| SA-004-25a | 2025-03-05. Service bulletin. ELECTRICAL SYSTEM. Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricted, thereby extending the transmitter battery life and the following will occur: The engine will not start unless the key transmitter is held over the Start Stop button. • Outside door handle lock/unlock touch sensor is inoperative. • Key transmitter indicator lights are inoperative. • The following DTC's may be stored: DTC B13D3:94 (Communication error with remote transmitter) ○ DTC P1260:00 (Immobilizer system problem). |
| SA-013-25 | 2025-03-05. Service bulletin. FUEL/PROPULSION SYSTEM; ELECTRICAL SYSTEM. Some customers may experience an inacurrate fuel gauge: Rapid fuel level drop when fuel guage is below 1/4. • Distance to empty reading (DTE) is incorrect. • DTC P0462:00 (Fuel gauge sender unit system: Low input) may be stored. • Engine no start and fuel guage shows vehicle has fuel, but engine starts after adding fuel. • This may be caused by a faulty Fuel Gauge Sender Unit (Sub). |
| SA-012-25 | 2025-03-05. Service bulletin. ELECTRICAL SYSTEM; UNKNOWN OR OTHER. Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure. |
| SA-011-25 | 2025-03-05. Service bulletin. UNKNOWN OR OTHER; STRUCTURE:BODY. Some customers will report that their fuel door was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-007/25 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2025 Mazda3 and 2020-2025 CX-30 are present. |
| SA-002-25a | 2025-03-05. Service bulletin. UNKNOWN OR OTHER. Some customers may experience the MyMazda App Remote Climate Control and the In-Vehicle Climate Control Timer functions are inoperative after DASH_ESU software update to "H" level. |
| 09-011-25 | 2025-03-04. Service bulletin. STRUCTURE:BODY. Some customers may complain that the driver’s side outer mirror glass vibrates when driving at high speeds at approximately 60 mph (100 km/hour ) or more on bumpy roads such as road joints, coarse-grained paved roads or rough roads. This is caused by insufficient hardness of the adhesive tape between the outer mirror glass holder and the mirror glass. To eliminate this concern, the material of the adhesive tape between the outer mirror glass holder and the mirror glass has been improved and the tape location has been modified. |
| 03-001-25 | 2025-03-04. Service bulletin. POWER TRAIN; UNKNOWN OR OTHER. Some vehicles may experience differential oil leaking from the oil seal (RH side) at the front differential. This is caused by an inappropriate assembly process of the front differential to the oil pan (vehicle side). To eliminate this concern the front differential assembly process has been changed |
| SA-005-25 | 2025-02-05. Service bulletin. STEERING. Before judging a steering wheel as having premature wear or a defect, first clean the steering wheel as explained in the repair information. Some vehicles may have steering wheel stains caused by chemicals such as hand lotions. |
| SA-004-25 | 2025-02-05. Service bulletin. ENGINE; ELECTRICAL SYSTEM; UNKNOWN OR OTHER. Key Transmitter Power Saving Function: When the key transmitter Power Saving Function is turned ON, transmitter battery power consumption is restricted, thereby extending the transmitter battery life. NOTE: Some customers may complain about an engine no start. This may be caused by the customer inadvertently putting the key transmitter in Power Saving Function. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.