Service bulletins for the 2019 Mazda CX-9
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
394 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| 06-003-20-3718b | 2020-10-02. Service bulletin. STEERING. Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified. |
|---|---|
| SA-063-20 | 2020-09-03. Service bulletin. ELECTRICAL SYSTEM. When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage. |
| SA-062-20 | 2020-09-03. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; PARKING BRAKE; VISIBILITY; FORWARD COLLISION AVOIDANCE. Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: • The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: • The windshield is dirty • The FSC lens is foggy • There is low visibility due to rain, fog or snow • It is at night and there is not enough light • There is direct or reflected sunlight on the FSC • There is problem with the FSC • There is a problem with the AUTOHOLD control function. • There is a problem with the electric parking brake (EPB). |
| MT-002-20 | 2020-09-02. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS; WHEELS. New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. |
| SA-058-20b | 2020-09-01. Service bulletin. ENGINE AND ENGINE COOLING. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. NOTE: Cylinder head replacement requires MASH authorization. |
| MT-003-20 | 2020-09-01. Service bulletin. ELECTRICAL SYSTEM. Some customers may complain about an inoperative power liftgate (PLG) and the any of the following DTC's stored in memory: • U3003:16 (Power liftgate (PLG) control module power supply voltage low input) • U3003:17 (Power liftgate (PLG) control module power supply voltage high input). This may be caused by low or high vehicle battery voltage. |
| 06-003-20-3718 | 2020-09-01. Service bulletin. STEERING. Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified. |
| SA-049-20 | 2020-08-05. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Some customers may experience an engine no start due to low battery voltage. Mazda is aware of the issue and is working on a solution. NOTE: Battery parasitic draw is intermittent. When the condition is present, battery parasitic draw exceeds 65 mA (0.065 A) 40 minutes after key OFF. |
| MT-001-20 | 2020-08-04. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices. |
| 09-006-20-3673a | 2020-08-04. Service bulletin. EQUIPMENT. When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). |
| 06-003-20-3718 | 2020-08-04. Service bulletin. ELECTRICAL SYSTEM; STEERING. Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified. |
| 05-003-20-3725 | 2020-08-04. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN; EQUIPMENT; ENGINE. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. |
| SA-053-20 | 2020-07-03. Service bulletin. POWER TRAIN. When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order to re-install the original plug from the old transmission. |
| SA-026-20a | 2020-07-03. Service bulletin. EQUIPMENT:ELECTRICAL. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. |
| 09-022-20-3720 | 2020-07-02. Service bulletin. STRUCTURE:BODY:BUMPERS. Some customers may notice cracks (as shown below) at one or both ends of the front bumper near the front fender / front combination light. This may be caused when driving over bumps. The bumper fascia may receive higher than expected forces, depending on driving manner and road conditions. To eliminate this concern, the internal shape and material of the front bumper fascia has been modified. |
| 09-020-20-3680 | 2020-06-02. Service bulletin. EQUIPMENT. Some customers may complain that the rear console / cup holder area is warming. The warming is caused by heat radiating from the rear heater core, which is located under the console. The warm air created by the heater core escapes through small gaps and carries heat along the inner walls of rear console / cup holder, causing an increase in temperature. |
| SA-049-20 | 2020-05-05. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may experience an engine no start due to low battery voltage. Mazda is aware of the issue and is working on a solution. NOTE: Battery parasitic draw is intermittent. When the condition is present, battery parasitic draw exceeds 65 mA (0.065 A) 40 minutes after key OFF. Contact Hotline for latest repair information. |
| SA-047-20 | 2020-05-05. Service bulletin. POWER TRAIN. Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory. |
| SA-041-20 | 2020-04-06. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. |
| SA-037-20 | 2020-04-06. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA. Some vehicles may have one of the following DTCs stored in memory: • C1001:92 - Forward sensing camera (FSC) poor field of view • B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. • In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). • In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details. |
| SA-036-20 | 2020-04-06. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. The owner’s manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts. CAUTION: Be aware that when cleaning the brand emblem, never use cleaning products that are highly acidic/alkaline detergent, organic solvents or those with aggressive chemical products, otherwise, the brand emblem may become cracked and/or deformed (as shown in the example below). Always refer customers to the owner’s manual for proper cleaning using cold or lukewarm water and a mild, neutral detergent. |
| 04-004-20-3679b | 2020-04-03. Service bulletin. SERVICE BRAKES, HYDRAULIC; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. Some vehicles may exhibit a click or squeak noise from the front brakes under the following conditions: Click Noise: 1. When first moving forward or reverse from a stop OR 2. When first applying the brakes while moving forward at slow speeds. Squeak Noise: During light braking. |
| 04-004-20-3679a | 2020-04-03. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; SERVICE BRAKES, HYDRAULIC. Some vehicles may exhibit a click noise from the front brakes under one of the following conditions: • When first moving the vehicle forward or reverse from a stop. • When first applying the brakes while the vehicle is moving forward at slow speeds. Due to deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. |
| 00-001-20-3689 | 2020-04-03. Service bulletin. SERVICE BRAKES, HYDRAULIC; POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. |
| 09-011-20-3644 | 2020-02-29. Service bulletin. VISIBILITY. Some vehicles may exhibit power outer mirror(s) that do not fold in and/or out when using the outer mirror switch. This concern may be caused by insufficient water tightness, allowing water to enter the electric folding unit resulting in corrosion damage. To eliminate this concern, the overlapping area (1) of the water-proof seal (inside electric fold-in unit) has been extended. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.