Service bulletin SA-049-20

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10177931
Published by NHTSA	2020-08-05
Manufacturer's number	SA-049-20
Manufacturer's date	2020-07-31
NHTSA component	ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM

NHTSA's summary

Some customers may experience an engine no start due to low battery voltage. Mazda is aware of the issue and is working on a solution. NOTE: Battery parasitic draw is intermittent. When the condition is present, battery parasitic draw exceeds 65 mA (0.065 A) 40 minutes after key OFF.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system, Engine

Vehicles listed
MAZDA CX-5	2020
MAZDA CX-9	2019, 2020

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SA-041-26a	2026-10-03. Service bulletin. DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button
01-010-26	2026-09-02. Service bulletin. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. 01-012/22 10/06/22 DESCRIPTION Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush. REPAIR PROCEDURE 1. Verify the customer concern. 2. If the above condition is experienced, remove the accumulated coolant around the pipe (1) with a wire brush etc. NOTE: Perform the procedure on the vehicle. No need to remove the water pipe and hoses.
SA-041-26	2026-07-03. Service bulletin. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
SA-027-26a	2026-07-03. Service bulletin. This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-027/26 04/16/26 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. REPAIR PROCEDURE 1. Perform appropriate repair to vehicle. If needed, use the Battery Diagnostics of the DCA-8000 to test the charging and starting systems by following the on-screen instructions for entering the appropriate information. Refer to the Mazda DCA-8000 Instruction Manual for more information.
09-019-26	2026-07-03. Service bulletin. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-012/21 12/13/21, 06/10/21 and 04/27/21 DESCRIPTION Some customers may experience all of following symptoms: The door lock/unlock operation will not work using the remote transmitter button. 1. The door lock/unlock operation will not work using the door lock/release touch sensor. 2. The engine will not start using the ignition switch. 3. The transmitter operates by itself. 4. The key battery drains faster than usual. 5. Symptoms 1-3: This may be caused when excess load is applied to the remote transmitter, deforming the electrical terminals and creating poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals. Symptom 4-5: This may be caused when excessive load is applied to the remote transmitter, creating a gap around the gasket where moisture enters and corrodes the circuit board which in turn drains the key battery faster than usual. To eliminate this concern, the thickness of the case wall on the gasket mounting surface has been increased and the bonding strength of the components has been improved to prevent deformation. REPAIR PROCEDURE • If the battery is bad or installed incorrectly, replace the battery and/or install it correctly. • If the remote power saving function is off and the battery is good and installed correctly, replace the defective remote transmitter with a modified one according to the instructions on MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING). NOTE: DO NOT replace other remote transmitter(s) for the vehicle if they not experiencing an issue.
SA-029-26	2026-05-05. Service bulletin. This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).
SA-027-26	2026-05-05. Service bulletin. This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-007/25 10/22/25, 06/02/25 and 02/03/25 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries. TEST PROCEDURE 1. Connect the charger clamps to the appropriate battery posts.
SA-026-26	2026-05-05. Service bulletin. This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.
SA-021-26	2026-05-05. Service bulletin. This Service Alert supersedes the previously issued SAs and bulletin(s) listed below: The changes are noted below in red. SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure.
SSPD8 Repair d	2026-04-04. Warranty extension. Subject: TSB 01-001/26 Warranty and Parts Kit Update INCLUDES: Warranty Extension Program - Special Service Program (SSP) D8 Check Engine Light ON with DTC P0126:00, 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6, 2020-2023 CX-30 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has made a change regarding related parts to TSB 01-001/26 which also impacts Warranty Extension Special Service Program (SSPD8). Parts Ordering and Warranty Claims: Effective March 5, 2026 only the related parts kit PYY2-15-SAY can be ordered and claimed for any repair. The two separate parts PYFB-15-169 and PE13-15-296 can no longer be claimed with repaired dates of March 5, 2026 and later. There is no change to the main part, the Plug PYY3-15-SA1. We have updated the TSB 01-001/26 and SSPD8 Repair Procedure and Parts & Warranty Information on Mazda Global Service Support (MGSS) to reflect this change.