WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Mazda CX-9

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

513 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Brakes are shown. Show all

Bulletins, newest first
04-002-19-35452019-02-19. Service bulletin. SERVICE BRAKES. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
00-003-18-3480a2018-11-13. Service bulletin. SERVICE BRAKES, HYDRAULIC; EQUIPMENT. Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.
SA-042-182018-10-09. Service bulletin. PARKING BRAKE; ELECTRICAL SYSTEM. DO NOT follow the instructions on MGSS for performing the ELECTRIC PARKING BRAKE (EPB) FORCED RELEASE PROCEDURE until these instructions are read, otherwise, damage to the EPB system may occur The instructions on MGSS are incorrect in one step, but will be corrected soon. NOTE: Performing the electric parking brake forced release procedure is necessary if the electric parking brake cannot be released by operating the electric parking brake switch or performing a recovery operation (*) due to a malfunction in the system or a discharged battery.
01-001-18-3419a2018-09-10. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; PARKING BRAKE:DRIVELINE:HYDRAULIC:ACTUATOR. After parking the vehicle at temperatures below the freezing, some customers may experience a lack of power with the check engine light on and DTC P0638:00 and/or P2112:00 stored in memory. - P0638:00: Throttle valve actuator control range/performance problem (one drive cycle DTC) - P2112:00: Throttle valve actuator motor current range/performance problem (one drive cycle DTC) This concern may be caused by condensed water in the intake manifold entering the throttle valve. After parking at temperatures below freezing, the throttle valve may be frozen at the stand-by position, resulting in the symptom. To prevent this concern, the control logic of the PCM has been modified to avoid frozen the throttle valve (by moving the valve at a certain time after the ignition has been turned off). NOTE: With this modification, the main relay may stay on up to 90 minutes after the ignition switch is turned off. "BATTERY INSPECTION" in the Workshop Manual will be modified to properly check the battery parasitic draw after this modification.
04-006-18-34962018-08-20. Service bulletin. SERVICE BRAKES, HYDRAULIC. Some vehicles may exhibit a squeaking noise from the front brakes during light braking. This concern usually occurs when the front brake pads have been worn to certain levels. Also, as the pads wear, the chamfer goes away and the grease between the pad and the shim deteriorates.To eliminate this concern, the chamfer shape of the brake pad has been modified to increase its durability.
00-003-18-34802018-07-02. Service bulletin. SERVICE BRAKES. Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare subject to denial or debit.
04-004-18-34682018-05-14. Service bulletin. SERVICE BRAKES. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
SA-052-172017-08-10. Service bulletin. SERVICE BRAKES. Smart City Brake Support (SCBS) frequently asked questions (FAQ)

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.