Service bulletins for the 2018 Mazda CX-5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
634 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| 01-002-21-3767 | 2021-02-05. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it. |
|---|---|
| 00-001-21-3768 | 2021-02-05. Service bulletin. STEERING; WHEELS; POWER TRAIN; ENGINE AND ENGINE COOLING. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. |
| SA-058-20c | 2021-01-06. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. NOTE: Cylinder head replacement requires MASH authorization. |
| SA-035-20b | 2021-01-06. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle. |
| CSP05a | 2020-12-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay™ / Android Auto™, A $1000 voucher towards the purchase or lease of a new Mazda vehicle |
| CSP05 | 2020-12-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay™ / Android Auto™, A $1000 voucher towards the purchase or lease of a new Mazda vehicle |
| MT-005-20 | 2020-12-03. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? • Yes - No repair is necessary. • No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE). |
| 01-006-20-3695b | 2020-12-03. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it. |
| SA-047-20a | 2020-11-04. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). CRACKED REAR DIFFERENTIAL: Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory. |
| SA-071-20 | 2020-11-04. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H |
| SA-061-20a | 2020-10-05. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. If you receive a customer concern about the CHECK IN light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, the cylinder deactivation oil control valve may be plugged with plastic debris from the oil filter wrapper. The debris may enter the center of the oil filter when poking a hole in the filter wrapper during removal, and then travel through the engine and plug the cylinder deactivation oil control valve. |
| 01-012-20-3738 | 2020-10-02. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone.• P2096:00 - Air fuel too lean • P2097:00 - Air fuel too rich • P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern. |
| SA-061-20 | 2020-09-01. Service bulletin. ENGINE AND ENGINE COOLING. If you receive a customer concern about the CHECK IN light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, perform the inspection in the Repair Procedure. |
| SA-058-20b | 2020-09-01. Service bulletin. ENGINE AND ENGINE COOLING. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. NOTE: Cylinder head replacement requires MASH authorization. |
| SA-058-20a | 2020-09-01. Service bulletin. ENGINE AND ENGINE COOLING. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. NOTE: Cylinder head replacement requires MASH authorization. |
| SA-058-20 | 2020-08-05. Service bulletin. ENGINE AND ENGINE COOLING. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats and cotters (IN/EX) are included in the new assembly. |
| SA-055-20a | 2020-08-05. Service bulletin. SERVICE BRAKES, AIR:SUPPLY:LOW PRESSURE WARNING:SWITCH; ENGINE AND ENGINE COOLING. If a customer comes in with the following concerns: • OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON. • DTC P055F and/or P0524 stored. • No driveability concern or engine mechanical noise. • Outside the VIN range in TSB 01-020/18. |
| 05-003-20-3725 | 2020-08-04. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN; EQUIPMENT; ENGINE. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. |
| SA-055-20 | 2020-07-03. Service bulletin. ENGINE AND ENGINE COOLING. If a customer comes in with the following concerns, perform the inspection procedure. • OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON. • DTC P055F and/or P0524 stored. • No driveability concern or engine mechanical noise. • Outside the VIN range in TSB 01-020/18. |
| 01-006-20-3695 | 2020-05-04. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it. |
| SA-035-20a | 2020-04-06. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: • The engine takes longer to warm up. • The engine temperature gauge fluctuates. • The low coolant temperature indicator (blue) light stays on longer or comes on while driving. • Poor heater performance, especially at idle. |
| SA-025-20a | 2020-04-06. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. The tapping noise will decreases as the vehicle is being driven or if the rpm is held above 2500 -3000 RPM. This may be caused by the valve Hydraulic Lifters (HLA) bleeding down as the engine cools or when the engine has been idling for an extended period of time, creating excessive valve lash clearance. |
| 00-001-20-3689 | 2020-04-03. Service bulletin. SERVICE BRAKES, HYDRAULIC; POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. |
| 01-003-20-3654 | 2020-02-29. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may experience a check engine light illumination with DTCs P24C6:00, P24AE:00, P24B1:00 and/or P24AF:00 stored in PCM memory. P24C6:00 - PM sensor: internal temperature sensor malfunction (1DC DTC) P24AE:00 - PM sensor control circuit range/performance problem (1DC DTC) P24B1:00 - PM sensor circuit high input (1DC DTC) P24AF:00 - PM sensor circuit range/performance (2DC DTC) [Particulate Matter (PM) Sensor] DTCs may be caused by the following: DTC P24C6:00: May be caused by water condensation in the exhaust system which may accumulate on the PM sensor element and result in cracks. DTCs P24AE:00, P24B1:00, P24AF:00: May also be caused by water condensation in the exhaust system which may accumulate on the PM sensor element and result in an incorrect output signal. To eliminate these DTCs, the following improvements have been made: The PM sensor has been improved (DTC P24C6:00). The mounting orientation of the PM sensor has been changed to reduce water accumulation (DTCs P24AE:00, P24B1:00, P24AF:00). The detection condition of DTCs P24AE:00 and P24B1:00 has been changed to 2DC, which will no longer detect a temporary incorrect sensor output |
| SA-035-20 | 2020-02-29. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.