WenmarOpen by Wenmar Pro

Service bulletin SA-058-20

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10177956
Published by NHTSA2020-08-05
Manufacturer's numberSA-058-20
Manufacturer's date2020-07-24
NHTSA componentENGINE AND ENGINE COOLING

NHTSA's summary

A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats and cotters (IN/EX) are included in the new assembly.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine

Vehicles listed
MAZDA CX-52018, 2019, 2020
MAZDA MAZDA32019, 2020
MAZDA MAZDA62018, 2019, 2020
MAZDA MX-52021

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20193222019-06-27. Engine
19V4970002019-06-27. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SA-038-26a2026-09-04. Service bulletin. This Service Alert supersedes the previously issued service alert listed below. The changes are noted in Red text. SA-038/26 06/15/26 DESCRIPTION Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote functions inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Index MAZDA CONNECT 2 Center Display Status Icon MAZDA CONNECT 3 Center Display Status Icon Remote Engine Start Will Not Function Remote Engine Start Function Will turn engine OFF Customer Subscription Status TCU Communication Line Status
01-010-262026-09-02. Service bulletin. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. 01-012/22 10/06/22 DESCRIPTION Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush. REPAIR PROCEDURE 1. Verify the customer concern. 2. If the above condition is experienced, remove the accumulated coolant around the pipe (1) with a wire brush etc. NOTE: Perform the procedure on the vehicle. No need to remove the water pipe and hoses.
SA-042-262026-07-03. Service bulletin. This Service Alert supersedes the previously issued SAs listed below. The changes are noted in Red text. SA-017/25 12/16/25, 09/08/25, 07/14/25, 05/15/25 and 03/21/25 DESCRIPTION Mazda Connect Frequently Asked Questions (FAQ) Index General Questions MAZDA CONNECT Indication Setup and Getting Started Dealer Processes Registration / Enrollment / Take-Over Customer Subscription Status WI-FI General Informatio Opening the TCU Communication Line WI-FI How-To Conditions for Remote Engine Start Will Not Function WI-FI Trial Period Conditions for Remote Engine Start Function Will turn engine OFF Interacting With The App TCU Communication Line Status Service Issues Educational Videos Troubleshooting Resources MyMazda App Error Codes Customer Opt-Out
SA-041-262026-07-03. Service bulletin. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
09-019-262026-07-03. Service bulletin. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-012/21 12/13/21, 06/10/21 and 04/27/21 DESCRIPTION Some customers may experience all of following symptoms: The door lock/unlock operation will not work using the remote transmitter button. 1. The door lock/unlock operation will not work using the door lock/release touch sensor. 2. The engine will not start using the ignition switch. 3. The transmitter operates by itself. 4. The key battery drains faster than usual. 5. Symptoms 1-3: This may be caused when excess load is applied to the remote transmitter, deforming the electrical terminals and creating poor contact with the battery. To eliminate this concern, the structure in the remote transmitter has been modified to reduce the deformation of the electrical terminals. Symptom 4-5: This may be caused when excessive load is applied to the remote transmitter, creating a gap around the gasket where moisture enters and corrodes the circuit board which in turn drains the key battery faster than usual. To eliminate this concern, the thickness of the case wall on the gasket mounting surface has been increased and the bonding strength of the components has been improved to prevent deformation. REPAIR PROCEDURE • If the battery is bad or installed incorrectly, replace the battery and/or install it correctly. • If the remote power saving function is off and the battery is good and installed correctly, replace the defective remote transmitter with a modified one according to the instructions on MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING). NOTE: DO NOT replace other remote transmitter(s) for the vehicle if they not experiencing an issue.
SA-029-262026-05-05. Service bulletin. This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).
SA-026-262026-05-05. Service bulletin. This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.
SSPD8 Repair d2026-04-04. Warranty extension. Subject: TSB 01-001/26 Warranty and Parts Kit Update INCLUDES: Warranty Extension Program - Special Service Program (SSP) D8 Check Engine Light ON with DTC P0126:00, 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6, 2020-2023 CX-30 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has made a change regarding related parts to TSB 01-001/26 which also impacts Warranty Extension Special Service Program (SSPD8). Parts Ordering and Warranty Claims: Effective March 5, 2026 only the related parts kit PYY2-15-SAY can be ordered and claimed for any repair. The two separate parts PYFB-15-169 and PE13-15-296 can no longer be claimed with repaired dates of March 5, 2026 and later. There is no change to the main part, the Plug PYY3-15-SA1. We have updated the TSB 01-001/26 and SSPD8 Repair Procedure and Parts & Warranty Information on Mazda Global Service Support (MGSS) to reflect this change.
SSPD8 Dlr Ltr a2026-04-04. Warranty extension. Subject: TSB 01-001/26 Warranty and Parts Kit Update INCLUDES: Warranty Extension Program - Special Service Program (SSP) D8 Check Engine Light ON with DTC P0126:00, 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6, 2020-2023 CX-30 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has made a change regarding related parts to TSB 01-001/26 which also impacts Warranty Extension Special Service Program (SSPD8). Parts Ordering and Warranty Claims: Effective March 5, 2026 only the related parts kit PYY2-15-SAY can be ordered and claimed for any repair. The two separate parts PYFB-15-169 and PE13-15-296 can no longer be claimed with repaired dates of March 5, 2026 and later. There is no change to the main part, the Plug PYY3-15-SA1. We have updated the TSB 01-001/26 and SSPD8 Repair Procedure and Parts & Warranty Information on Mazda Global Service Support (MGSS) to reflect this change.
SA-014-262026-04-02. Service bulletin. This Service Alert supersedes the previously issued SA(s) and TSB(s) listed below: The changes are noted in Red. SA-035/24 05/31/24 DESCRIPTION There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not. A mechanical seal (A) is used for the water pump. This mechanical seal can seal coolant (B) by sliding a mating ring (C) against a seal ring (D). When the sliding surface temperature of the mechanical seal is more than 248 °F (120 °C) while driving, a small amount of steam (E) is leaked and bleeds through the bleeding hole (F). After drying, the steam leaves a green coolant deposit near the water pump bleed hole (F). This is a normal condition and does not require water pump replacement. The water pump should only be replaced if there is an accumulation of crystallized coolant near the bleed hole. When you encounter a water pump with coolant seepage marks, decide to replace it or not based on the following criteria using sample photos. NOTE: During the initial period of use*, the sliding surfaces of the seals may not yet be fully settled, which can temporarily increase the amount of leakage. Continued use will allow the surfaces to settle, reducing the leakage. Replacing parts that are already settled with new ones will increase the leakage again until the new parts become conditioned. Therefore, replacement should be avoided in this initial period of use. *As a guideline, this applies to vehicles with less than 1,860 miles (3000 km) of mileage.