WenmarOpen by Wenmar Pro

Service bulletins for the 2021 Lincoln Corsair

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

186 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
SSM 527222024-08-06. Service bulletin. UNKNOWN OR OTHER. Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various FordPass/LincolnWay connectivity concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software
SSM 527042024-08-05. Service bulletin. UNKNOWN OR OTHER. Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.
SSM 526752024-07-03. Service bulletin. UNKNOWN OR OTHER. Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level
SSM 526332024-07-03. Service bulletin. UNKNOWN OR OTHER. Some 2020-2024 Escape/Corsair, 2021-2024 Bronco Sport/F-150, and 2022-2024 Maverick vehicles may exhibit a condition where the door(s) do not open using the exterior door handle(s). This may be due to an enabled door reinforcement inertia lock within the exterior door handle. This condition occurs when the doors are closed or opened with excessive force. To correct this condition, follow the door reinforcement inertia lock rest procedure that has been added to Section 501-14 of the Workshop Manual under General Procedures. For claiming, use causal part 78219A64.
23N062024-07-02. Service bulletin. ENGINE. Certain 2021-2022 Model Year Corsair, 2020-2022 Model Year Escape and 2022-2023 Model Year Maverick Vehicles Equipped With 2.5L HEV/PHEV Engine Long Block Replacement In some of the affected vehicles, after safety recall 23S27 has been performed, the Malfunction Indicator Light (MIL) may illuminate and store Diagnostic Trouble Codes (DTCs) P1061 and/or P032F. This could be due to a faulty connecting rod bearing that was detected by the Powertrain Control Module (PCM).
TSB 24-21822024-06-13. Service bulletin. UNKNOWN OR OTHER. This article supersedes TSB 23-2307 to update the Service Procedure and vehicle model years affected. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.
TSB 24-21852024-06-12. Service bulletin. POWER TRAIN. This article supersedes TSB 23-2335 to update the TSB title, vehicles affected and parts list. Some 2021-2023 Bronco Sport vehicles equipped with a 1.5L engine built on or before 30-Nov-2022, 2021-2022 Bronco Sport vehicles equipped with a 2.0L engine built on or before 28-Feb-2022, 2020-2022 Escape/Corsair vehicles equipped with 1.5L/2.0L/2.3L engines built on or before 30-Apr-2022, 2020-2022 Escape vehicles equipped with 2.5L full hybrid electric vehicle (FHEV) powertrain built on or before 31-Mar-2022 may exhibit a chatter/shudder during low speed turning events. This may be due to contamination of the rear drive unit (RDU) fluid through the RDU vent hose. To correct the condition, follow the Service Procedure to replace the RDU vent hose.
TSB 24-21392024-06-03. Service bulletin. POWER TRAIN. Some 2020-2024 Escape and Corsair Vehicle equipped with the 8F35 or the HF45 transmission may exhibit a click or ting noise during acceleration from a stop, or in some cases during the end of a stop event. This may be due to the front half shaft sticking to the wheel bearing surface. To correct this condition, perform the Service Procedure below to lubricate the halfshaft and wheel bearing hub assembly mating surface.
SSM 524992024-05-03. Service bulletin. UNKNOWN OR OTHER. Some 2020-2022 Corsair vehicles equipped with a head-up display (HUD) may exhibit a condition where the display does not allow the projection height to be adjusted properly. This may be due to the software installed in the HUD. To correct this condition, reprogram the HUD using the latest software level of the Ford Diagnosis and Repair System (FDRS) diagnostic tool. For claiming, use causal part 19G468 and applicable labor operation in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 524102024-04-24. Service bulletin. UNKNOWN OR OTHER. Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
22N152024-04-02. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Customer Satisfaction Program 22N15 Certain 2020-2023 Model Year Bronco Sport, Escape, Corsair, E-Series, F-650/F-750, F-53 Motorhome Chassis, F-59 Commercial Stripped Chassis Vehicles Equipped with Smart Data Link Connector (SDLC) Gateway Module Reprogramming for Inspection and Maintenance (I/M) Testing Adding Not OTA Capable Owner letters. Other documents submitted 01/02/24 & Received OTA letters submitted on 02/01/24
SSM 523352024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 523292024-03-20. Service bulletin. ELECTRICAL SYSTEM:ADAS:HUD:SOFTWARE. Some 2020-2022 Corsair vehicles equipped with a head-up display (HUD) may exhibit a condition the display does not allow the projection height to be adjusted properly. Ford is aware of the concern and this condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected by the end of April 2024. Replacement/reprogramming of the HUD will not resolve this condition. Monitor OASIS for additional information and schedule a service appointments for customers once the repair becomes available.
SSM 523142024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 523072024-03-05. Service bulletin. ELECTRICAL SYSTEM. Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
22N152024-02-01. Service bulletin. ELECTRICAL SYSTEM:BODY CONTROL MODULE:SOFTWARE; UNKNOWN OR OTHER. Certain 2020-2023 Model Year Bronco Sport, Escape, Corsair, E-Series, F-650/F-750, F-53 Motorhome Chassis, F-59 Commercial Stripped Chassis Vehicles Equipped with Smart Data Link Connector (SDLC) Gateway Module Reprogramming for Inspection and Maintenance (I/M) Testing Addinf owner letters. First part submitted 01/02/24
SSM 522012024-01-30. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Some 2020-2023 Escape, 2021-2023 Corsair vehicles equipped with 2.5L engine full hybrid electric vehicle (FHEV) and plug-in hybrid electric vehicle (PHEV) powertrain and 2022-2023 Maverick vehicles equipped with 2.5L engine FHEV powertrain may exhibit a condition where the 12V battery voltage is low or discharged with diagnostic trouble code (DTC) U3003:62 stored in the direct current/direct current (DC/DC) converter control module. The vehicle may also exhibit DTC U3003:16 and/or U3000:04 stored in the DC/DC converter control module. This may be due to an open in the 300 amp high-current fuse F4 located in the high-current battery junction box (BJB). To correct this condition, refer to Workshop Manual (WSM), Section 414-05 > Pinpoint Test H to verify the 300 amp high-current fuse condition. If the high-current fuse is found to be open, replace the high-current fuse per the application listing in the parts catalog. Recharge and test the 12v battery. For repairs under warranty, use the base part number of the component that caused the damage to the fuse.
SSM 521962024-01-30. Service bulletin. ELECTRICAL SYSTEM. Some 2020-2022 Aviator and 2021-2022 Corsair hybrid vehicles built on or before 01-Apr-2022 may exhibit charging concerns with the Lincoln dual-voltage charging cord (TurboCord). This style of charging cord can be indentified by one of the 220V prongs positioned sideways. If the vehicle charges properly using a 110/120V non-ground fault interrupter (GFI) outlet with the original 220V adapter removed, replace the adapter (part number VLC5Z-10B706-B) alone. This replacement adapter is available from accessories.lincoln.com > keyword search Turbo Cord, or through the local Ford Authorized Distributor (FAD). Discoloration of the 220V adapter or dual voltage charging cord could indicate a problem with the electrical outlet used; if so a licensed electrician should inspect. For further diagnostic assistance, contact Webasto Charging systems, Inc. directly at 888-219-6747 or at evscs@webasto.com.
22N152024-01-02. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Certain 2020-2023 Model Year Bronco Sport, Escape, Corsair, E-Series, F-650/F-750, F-53 Motorhome Chassis, F-59 Commercial Stripped Chassis Vehicles Equipped with Smart Data Link Connector (SDLC) Gateway Module Reprogramming for Inspection and Maintenance (I/M) Testing
SSM 520242023-11-04. Service bulletin. HYBRID PROPULSION SYSTEM; ENGINE AND ENGINE COOLING. Some 2020-2023 Escape/2021-2023 Corsair equipped with 2.5L engine full hybrid electric vehicle (FHEV) and plug-in hybrid electric vehicle (PHEV) powertrain and 2022-2023 Maverick vehicles equipped with 2.5L engine FHEV powertrain may exhibit a condition where the 12V battery voltage is low or discharged with diagnostic trouble code (DTC) U3003:62 stored in the direct current/direct current converter control module (DC/DC). The vehicle may also exhibit DTC U3003:16 and/or U3000:04 stored in the DC/DC module. This may be due to an open in the 300 amp high-current fuse F4 located in the high-current battery junction box (BJB).
SSM 519962023-11-03. Service bulletin. LANE DEPARTURE: LANE KEEP: AUTOMATIC STEERING. Some 2020-2023 Escape/Corsair vehicles may exhibit a condition where the vehicle drifts left and right within the vehicle's lane while the lane keeping assist is active. The lane keeping aid assists the driver by providing steering torque to help the driver keep the vehicle in the lane when it detects unintentional drifting toward the outside of the lane. Additionally, adaptive cruise control with lane centering provides constant steering torque to keep the vehicle centered in the lane while cruise control is engaged. These are operating characteristics of the lane keeping systems. Refer to the Owner's Manual for complete description of the operation of these systems. Do not attempt diagnosis or repairs or submit a claim for this condition. Inform the customer that the lane keeping system is only an aid, and their hands should stay on the steering wheel at all times while driving.
TSB 23-23352023-11-03. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Some 2021-2023 Bronco Sport vehicles equipped with a 1.5L engine built on or before 30-Nov-2022, 2021-2023 Bronco Sport vehicles equipped with a 2.0L engine built on or before 28-Feb-2022 or 2020-2022 Escape/Corsair non-plug in hybrid electric vehicle (PHEV) vehicles built on or before 30-Apr-2022 may exhibit a chatter/shudder during low speed turning events. This may be due to contamination of the rear drive unit (RDU) fluid through the RDU vent hose. To correct the condition, follow the Service Procedure to replace the RDU vent hose.
TSB 23-23072023-11-02. Service bulletin. UNKNOWN OR OTHER; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.
SSM 519232023-10-04. Service bulletin. UNKNOWN OR OTHER; SERVICE BRAKES. Some 2020-2022 Escape and 2021-2022 Corsair vehicles may exhibit a condition where the brake service mode is inoperative using the Workshop Manual (WSM) routine and/or Parking Brake Limited Function-Service Required message displayed in the instrumental panel cluster (IPC) after opening the drivers door. This may be due to the software installed in the anti-lock brake system (ABS) module. To correct this condition, reprogram the ABS module to the latest software available. For claiming, use causal part number 2C219 and the applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.
SSM 519082023-10-04. Service bulletin. STRUCTURE:BODY:HOOD; STRUCTURE:BODY:DOOR; LATCHES/LOCKS/LINKAGES; STRUCTURE:BODY:HATCHBACK/LIFTGATE. Some 2020-2023 Escape/Corsair vehicles may exhibit a door ajar warning indicator or higher than expected efforts to fully close doors. Verify the hood/liftgate are not open. Confirm all doors are fully closed and latches are fully engaged. Doors will not fully close when lightly letting go of the door or letting it swing closed from a short distance under its own weight. Push/pull effort must be applied to doors while closing to fully engage latch and turn off the ajar signal warning. If doors are still not fully latching closed, manually adjust door striker position to allow for proper alignment and engagement to the door latch. The door hang position may also need to be slightly adjusted to achieve the same effect. Refer to Workshop Manual (WSM), Section 501-03.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.