WenmarOpen by Wenmar Pro

Service bulletins for the 2023 Lincoln Aviator

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

130 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
SSM 517202023-06-22. Service bulletin. EQUIPMENT; SEATS. Some 2020-2023 Explorer/Aviator vehicles may have a concern where the second row outboard manual/power seats do not fold, exhibit excess effort to fold, or do not slide forward/backward easily. Power or manual second row seats must be pushed forward manually during easy entry function since the assist spring will reduce but not eliminate manual effort. Refer to the Owner's Manual > Seats > Rear Seats > Adjusting the Second Row Rear Seats for further details. If the seats do not easily push forward manually, it maybe due to tension in the seat track due to uneven assembly torque. To correct these conditions, unbolt the second row seat frame from the floor to relax tension. Start the bolts by hand, then tighten in the correct sequence and torque per Workshop Manual (WSM) Section 501-10B.
SSM 517252023-06-21. Service bulletin. ELECTRICAL SYSTEM. Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 516872023-06-16. Service bulletin. UNKNOWN OR OTHER; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; POWER TRAIN. TSB 22-2428 is missing some labor operations. For any missing labor operations, claim available new model labor operations or m-time. Refer to this article on the repair order. When replacing the CDF cylinder, the current TSB does not require a complete transmission overhaul or cooler and converter flushing. Ford is currently reviewing the TSB. Monitor OASIS for updates.
SSM 517012023-06-13. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Some 2020-2023 Aviator/Explorer vehicles equipped with a 3.0L hybrid engine may exhibit illuminated powertrain malfunction (wrench) indicator and stop safely now warning. Diagnostic trouble code (DTC) P0AA6:00 may be stored in the battery energy control module (BECM). Inspect the right side frame rail area near the bank 1 charge air cooler (CAC) intake pipe clamp for chafing the orange high voltage harness. If the harness is damaged, de-energize high voltage system per Workshop Manual (WSM), Section 414-03A. Reposition the clamp and replace the high voltage harness (14290). If the harness is not damaged continue P0AA6 diagnostics in WSM, Section 414-03A, Pinpoint Test T. For a P0AA6 diagnostic aid video, refer to Professional Technician System (PTS) > Home > Technical Assistance > Technical Support Videos > enter P0AA6 in search box and click video returned.
TSB 23-21442023-06-07. Service bulletin. POWER TRAIN. Some 2023 Bronco/Explorer/Aviator vehicles equipped with a 10R60 automatic transmission built on 8-Dec-2022 and through 22-Dec-2022 may exhibit a whine noise during coast down from 25 mph (40 km/h). Vehicles built on 6-Feb-2023 and through 1-Mar-2023 may exhibit a whine noise during acceleration in 1st gear. These conditions may be caused by the machining of the No. 4 shell and sun gear. To correct the conditions, follow the Service Procedure to replace No. 4 shell and sun gear.
TSB 22-24282023-05-30. Service bulletin. POWER TRAIN. Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60 transmission and built on or before 23-Dec-2022 or with a 18R80/10R80MHT transmission and built on or before 15-Aug-2022 may exhibit a harsh/delayed engagement and/or harsh/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the PCM or TCM, the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
SSM 516652023-05-29. Service bulletin. ENGINE AND ENGINE COOLING. Some 2021-2023 Ford and Lincoln vehicles equipped with a 2.7L or 3.0L engine may exhibit an upper engine thump/knock noise coming from the left cylinder head. This condition is most noticeable at idle and may lessen at higher engine speed or while driving. This condition does not affect vehicle durability and will not get worse over time. Use a stethoscope or chassis ears and listen just behind the left cylinder head intake VCT solenoid on the cam cover to determine if the thump/knock noise is coming from the cylinder head/camshaft. The left cylinder head and the camshaft roller followers are available as service parts.
SSM 516402023-05-16. Service bulletin. SUSPENSION. Some 2020-2023 Aviator vehicles equipped with air suspension may require service of a front air spring/strut. Complete front air spring/strut assemblies are now available and can be replaced instead of replacing individual components of the front air spring or front struts for warranty and retail repairs. Part numbers are LC5Z-3C098-A (right) and LC5Z-3C098-C (left) for non-hybrid vehicles, and LC5Z-3C098-B (right) and LC5Z-3C098-D (left) for hybrid vehicles. Front spring/strut assembly replacement is recommended to make sure a successful repair is performed.
SSM 516222023-05-16. Service bulletin. EQUIPMENT. 2022-2023 Explorer/Aviator vehicles built on or after 28-May-2022, 2022-2023 Expedition/Navigator vehicles built on or after 08-Jun-2022 and 2022 Escape/Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.
SSM 516212023-05-16. Service bulletin. SUSPENSION. Some 2020-2023 Aviator vehicles equipped with air suspension may exhibit a drive malfunction and/or suspension fault message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) B1041 and U2100 stored in the SUMA. This may be due to the SUMA entering diagnostic service mode after an on-demand (OD) self-test following suspension system diagnosis or repair. Use the Ford Diagnosis and Repair System (FDRS) > SUMA > Run All CM (Continuous Memory) DTCs. Do not run FDRS > SUMA > OD and CM DTCs to prevent invalid DTCs. If an OD self-test was run, clear DTCs using FDRS > SUMA > Transport and Factory Mode Deactivation function. For other DTCs refer to Workshop Manual (WSM), Section 204-05 (Vehicle Dynamic Suspension) for normal diagnostics.
SSM 515362023-05-04. Service bulletin. STRUCTURE. For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
SSM 515642023-05-04. Service bulletin. EQUIPMENT. 2022-2023 Police Interceptor Utility (gas engine) and all 2022-2023 Explorer vehicles built on or after 14-Jul-2022, 2022-2023 Police Interceptor Utility (hybrid) vehicles built on or after 17-Aug-2022, 2023 Aviator (gas engine) vehicles built on or after 18-Jul-2022, and 2023 Aviator (hybrid) vehicles built on or after 27-Jul-2022 are not equipped with a rear parking aid camera wash feature. The feature was deleted; however, the rear parking aid camera washer jet may still be present without a hose attached to it. This is normal and no repair attempts should be made.
SSM 515392023-05-04. Service bulletin. STRUCTURE:BODY:DOOR. Some 2020-2023 Aviator vehicles built on or before 20-March-2023 may exhibit a passenger door window control switch to bezel rattle while audio volume is playing from speakers that could be mistakenly diagnosed as a speaker issue. This may be due to the natural frequencies of the switch and bezel when excited by sound. To diagnose, perform Workshop Manual (WSM) Section 415-00 > Pinpoint Test E1. Use the 100Hz audio sample file from the Speaker Audio Test link within Pinpoint Test E1, and adjust fade and balance settings to passenger front speaker. If the rattle is isolated to the passenger door switch bezel, remove per WSM Section 501-11. Apply Rotunda flock tape (164-R4903) over the underside of the bezel and the switch in a U-shape, then reassemble. Rerun Pinpoint Test E1 to verify the repair. If the rattle persists, perform the remaining Pinpoint Test E steps.
SSM 515312023-05-04. Service bulletin. POWER TRAIN. Some 2020-2023 Explorer/Aviator/Transit, 2021-2023 F-150/Bronco, 2022-2023 Expedition/Navigator/Mustang and 2023 F-250/F-350 Super Duty vehicles may exhibit harsh/delayed engagement and/or harsh/delayed shift concerns. These may be addressed with the powertrain control module (PCM)/transmission control module (TCM) Transmission Accelerated Main Control Break In Routine and/or a main control overhaul. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart if DTCs are present and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. Cycling the shift solenoids and clutch control valves to remove contamination must be performed along with an adaptive drive cycle before attempting repair. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) Manual.
SSM 515152023-04-06. Service bulletin. ELECTRICAL SYSTEM. 2020-2023 Explorer/Aviator with start/stop push button ignition switch may exhibit an illuminated malfunction indicator lamp (MIL) and powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) B108A:01 (general electrical failure), B108A:24 (signal stuck high), and/or B108A:9E (stuck on). The ignition mode light emitting diode (LED) indicator may also flash quickly. This condition may be caused by loose wiring terminal crimps on connector C2195 at the push button ignition switch. Examine Pin 1 (CPK34/Gn) first, since it is the only pin with the smallest (26 gauge) wire. To correct this condition, repair terminal crimps per Wiring Diagram (WD) Cell 5. If no wiring terminal faults are found, refer to Workshop Manual (WSM) Section 211-05 for normal diagnostics. The push button ignition switch pinpoint tests in the WSM have been updated.
SSM 515132023-04-06. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 Ford and Lincoln vehicles may exhibit a condition where the high voltage battery stops charging when connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). To restore charging capability, disconnect the off-board charging station charge handle from the vehicle charge port and reconnect. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in June 2023. Replacement of the SOBDM will not resolve this condition. Monitor OASIS for additional information.
SSM 514492023-04-05. Service bulletin. EQUIPMENT:ELECTRICAL. Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 514392023-04-05. Service bulletin. POWER TRAIN. Some 2020-2023 Explorer/Aviator 4x4/AWD vehicles with hybrid powertrain may experience a harshness and/or vibration felt through the seat, steering wheel and/or center console after initial driveaway between 25-50 MPH (40-80 Km/h) that lessens after driving 5-10 minutes. This may be due to driveshaft center bearing bounce mode during cold ambient temperatures. To resolve the concern, install a softer durometer L1MZ-4A499-F driveshaft center bearing per Workshop Manual Section 205-01. For claiming, use causal part 4A499 and applicable labor operations in Section 4 of the Service Labor Time Standards (SLTS) Manual.
SSM 514192023-04-04. Service bulletin. POWER TRAIN. Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability.
SSM 513802023-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2020-2023 Explorer/Aviator vehicles may exhibit the A/C blowing warm air with DTCs P0645, P2CFC, and/or P2CFD present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the WSM. Test the function of the A/C to verify that it is blowing cold air.
SSM 513382023-03-04. Service bulletin. BACK OVER PREVENTION:DISPLAY FUNCTION; ELECTRICAL SYSTEM. Some 2020-2023 Aviator vehicles may exhibit a concern where the center display screen will not shift to night mode or has lines on the center display screen with multi color or rainbow hue. This may be due to accessory protocol interface module (APIM) software. To correct the condition, run the APIM-SYNC Module (APIM) Standard Programming application using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 513062023-02-02. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2023 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
SSM 512972023-01-31. Service bulletin. POWER TRAIN. Some 2020-2023 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2D40. This may be due to the high voltage battery thermal system not cooling as it should. Follow the updated WSM Section 414-03 including listed possible sources, visual inspection and prechecks, and diagnostic procedures.
SSM 512932023-01-31. Service bulletin. SEATS. 2022-2023 Lincoln Aviator vehicles equipped with multi-contour front seats have driver seat control module G (SCMG) and passenger seat control module H (SCMH) seat modules available separately at a lower level service part from the seat back frame (5461018/7861018/7861019). If diagnosis determines that replacement of either multi-contour front seat module is required, it is not necessary to replace the complete seat back frame. Refer to the service part catalog for the correct front seat module part number (14F548/14F549) and Workshop Manual (WSM) Section 501-10A for replacement procedures.
SSM 512652023-01-06. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR; EQUIPMENT. Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.