WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Jeep Wrangler

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

836 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S2003000001ReVD2022-09-26. Service bulletin. POWER TRAIN. Noise From Front Axle Area Over Bumps
S2019000005RevA2022-09-26. Service bulletin. STEERING; ELECTRICAL SYSTEM; POWER TRAIN; AIR BAGS. U0131 Lost Communication With Power Steering Control Module A DTC Active. EPS Light On.
90041012022-09-15. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION; EQUIPMENT. Clutch System Related Components For vehicles equipped with manual transmissions (sales code DEM) with a low mileage clutch failure please contact one of the following prior to repairs: Ganesh Maharajan: (248) 944-3018 or Cody Nofzinger: (248)-944-5847 If no response in 15 minutes, proceed with repair.
08-003-212022-07-18. Service bulletin. STEERING; POWER TRAIN. Improved Steering Feel This bulletin involves replacing the steering gear and updating the Electric Hydraulic Power Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all steps necessary to complete the Repair Procedure. If any steps are missed, this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excessive play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.
S1918000008 Rev.2022-07-18. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EQUIPMENT; POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Customer?s complaint may include a MIL-on with one or more of the following DTCs (Active, Pending, or Stored) in the PCM: P0133, P0137, P0171, P0300, P2096. The root cause could be due to oil leaking from Bank 1 valve cover seal on to the 1/2 (Bank 1 downstream) O2 sensor. This can adversely affect the 1/2 O2 sensor signal reading and lead to listed DTCs. Before performing normal diagnostic routines for the above codes, check for the condition listed above.
742442021-06-28. Service bulletin. POWER TRAIN. Warranty Bulletin D-20-23 Part Order Restriction Program - 48V Power Pack Unit (PPU) - Select 2018 - 2021 Jeep Wrangler (JL) and 2019 - 2021 RAM (DT) (Rev. A)
S2023000020 Rev.2021-05-24. Service bulletin. BACK OVER PREVENTION; POWER TRAIN. Tick Noise From A-pillar Front Power Top Side Rail
S2008000113 Rev.2021-05-24. Service bulletin. POWER TRAIN. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S1821000005 Rev.2021-04-26. Service bulletin. POWER TRAIN. Required Updates When Changing Tire Sizes, Installing Mopar Lift Kits With Larger Tires, Manual Transmission Vehicles Setting DTC P08A6
08-003-212021-02-16. Service bulletin. STEERING; POWER TRAIN. Improved Steering Feel This bulletin involves replacing the steering gear and updating the Electric Hydraulic Power Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all steps necessary to complete the Repair Procedure. If any steps are missed, this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excessive play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.
S20180000122020-12-28. Service bulletin. ELECTRICAL SYSTEM; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Check engine lamp on. Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.
18-022-20 REV. A2020-12-21. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs:P012A - Turbocharger/Supercharger Inlet Pressure Sensor 1. P012C - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low. P012D - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High. P0607 - ECU Internal Performance. P06EF - Engine Restart Performance. P050B - Cold Start Ignition Timing Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P0128 - Thermostat Rationality. P0507 - Idle Speed Performance Higher Than Expected. Customers may also describe the following condition:Excessive radiator fan noise when the A/C is on MAX output. In addition, the following software enhancements are available:Electric Vacuum Pump (EVP) update. Fan noise reduction.
S20180000122020-12-21. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Check engine lamp on. Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.
08-074-202020-09-28. Service bulletin. STEERING; POWER TRAIN. Improved Steering Feel This bulletin involves replacing the steering gear and updating the Electric Hydraulic Power Steering (EHPS) software, if required. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excess play.This service bulletin repair will NOT correct a sustain steering shake, shimmy or vibration. If this repair is performed on a vehicle with those symptoms, that will cause a dissatisfied customer and a repeat visit to the dealer.
90037042020-08-24. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; POWER TRAIN. Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
18-021-20 REV. A2020-07-27. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P012A - Turbocharger/Supercharger Inlet Pressure Sensor 1(APAC, EMEA and LATAM Only). P012C - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low(APAC, EMEA and LATAM Only). P012D - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High(APAC, EMEA and LATAM Only). P2C90 - Crankcase Ventilation System - Hose "A" Disconnected(APAC, EMEA and LATAM Only). P06EF - Engine Restart Performance. P04FC - Crankcase Ventilation System Performance. P050B - Cold Start Ignition Timing Performance. P0128 - Thermostat Rationality. P0456 - EVAP System Small Leak. If DTC P0456 is present, use the wiTECH Small Leak Verification Test (SLVT) to determine if there is a leak in the system. The following software enhancement is also available in this update:Enable soot retention for vehicles equipped with Gasoline Particulate Filter (GPF). Technicians may also experience the following:Unable to read data information from the OBD II connector when using a generic scan tool(APAC Only).
657102020-07-27. Service bulletin. EQUIPMENT; POWER TRAIN:CLUTCH ASSEMBLY. Safety Recall W12 JL/JT Clutch Update to Dealer Instructions for Parts Ordering
S20080000752020-07-27. Service bulletin. POWER TRAIN. No Start, Start Stop Inoperative, Cluster Messages to Service Shifter or Service Start Stop System
S18210000052020-06-22. Service bulletin. POWER TRAIN; EQUIPMENT; TIRES. Required Updates When Changing Tire Sizes, Installing Mopar Lift Kits With Larger Tires, Manual Transmission Vehicles Setting DTC P08A6
S20230000202020-05-26. Service bulletin. BACK OVER PREVENTION; POWER TRAIN. Tick Noise From A-pillar Front Power Top Side Rail
S20250000022020-05-26. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Customer complaint includes check engine/MIL light on. Upon further inspection, fault codes will be found in the powertrain control module (PCM) for P0441, P0443 or P0449. Fault codes may be either active or stored.
18-021-202020-05-18. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P06EF - Engine Restart Performance. P04FC - Crankcase Ventilation System Performance. P050B - Cold Start Ignition Timing Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P0128 - Thermostat Rationality. The following software enhancement is included:Enable Soot Retention for vehicles equipped with Gasoline Particulate Filter (GPF). Customer or technician may also experience the following:Unable to read data information from the OBD II connector when using a generic scan tool(APAC Only).
18-021-202020-04-27. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P06EF - Engine Restart Performance. P04FC - Crankcase Ventilation System Performance. P050B - Cold Start Ignition Timing Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P0128 - Thermostat Rationality. The following software enhancement is included:Enable Soot Retention for vehicles equipped with Gasoline Particulate Filter (GPF). Customer or technician may also experience the following:Unable to read data information from the OBD II connector when using a generic scan tool(APAC Only).
18-022-202020-04-27. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P06EF - Engine Restart Performance. P050B - Cold Start Ignition Timing Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P0128 - Thermostat Rationality. P0507 - Idle Speed Performance Higher Than Expected. Customers may also describe the following condition:Excessive radiator fan noise when the A/C is on MAX output. In addition, the following software enhancements are available:Electric Vacuum Pump (EVP) update. Fan noise reduction.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.