WenmarOpen by Wenmar Pro

Service bulletins for the 2021 Jeep Grand Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1325 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Wheels are shown. Show all

Bulletins, newest first
S2523000032 REV.B2026-08-19. Service bulletin. WHEELS; STEERING. Steering Dragging While Recreational Flat Towing Behind RV.
S2521000004 Rev.A2026-01-07. Service bulletin. SUSPENSION; STEERING; WHEELS. Note: actual release date was 12/22/2025 The customer is experiencing a clicking or pop noise from the steering knuckle and bearing area during turns while driving.
S25220000032025-10-15. Service bulletin. WHEELS. Tire Pressure Monitor (TPM) Warning Lamp On Or Flashing. Sensor(s) Not Reading And Or Showing Dashes.
S2422000001 REV.C2024-11-13. Service bulletin. WHEELS; ELECTRICAL SYSTEM. Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
S23020000042023-10-02. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); SUSPENSION; BACK OVER PREVENTION; ELECTRICAL SYSTEM; WHEELS. Air Suspension Control Module (ASCM) Wheel Acceleration Sensor Diagnostic Trouble Codes (DTCs) C15D1-01 And Or C15D2-01.
0805022REVA2023-01-17. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; WHEELS; STEERING; STRUCTURE; PARKING BRAKE; VEHICLE SPEED CONTROL; VISIBILITY. Flash: Body Control Module (BCM) Updates This bulletin involves reprogramming the Body Control Module (BCM) with the latestavailable software. Customer may describe various LIN related functions (steering wheel, center stack, terrain or 4wd) switchesand/or certain interior lamps not working. Upon further inspection the technician may also observe the following DTCs may have set withouta MIL: U1223-00 - Lost Communication with Wireless Charging Pad Module. U121E-00 - Lost Communication With Steering Wheel Cruise Control Switch. U1207-00 - Lost Communication With Terrain Switch Bank Module. U1191-00 - Lost Communication with Switch Bank Module 2. U1153-00 - Lost Communication With Windshield Wiper Smart Module. U114F-00 - Lost Communication with LIN Overhead Console. U114D-87 - Lost Communication with Hands Free Liftgate Module-Missing Message. U113B-00 - Lost Communication With Switch Bank Module. U112D-00 - Lost Communication With EVIC Steering Wheel Switches. U1125-00 - Lost Communication With LIN ECU 5- (Ride Height Switch Module). U1123-00 - Lost Communication With LIN ECU 3- (Switch Bank Module Rear Right). U1122-00 - Lost Communication With LIN ECU 2- (Switch Bank Module Rear Left). U1008-00 - LIN 1 Bus Steering Column Control Module Electrical Diagnostic. U0231-00 - Lost Communication With Rain Sensing Module. In addition, the customer may experience one or more of the following:Fuel Level and Range (distance to empty) (DTE) will both increase aftersleep cycle. Fuel Level % would increase when parked on a slope. Fuel gauge remains at full for 107 km (67 miles) vs. 73 km (45 miles). After fueling up with 68 liters (18.1 gallons) of fuel, the fuel gauge onlywill read around 1/4 tank and the low fuel lamp is still illuminated. After 10 minutes of driving, the gauge only read around 3/4 tank andthe fuel lamp is still on. Refuel button is pressed for a short duration of 500ms or less at key off,then the fuel door is not opened.
S21230000612023-01-17. Service bulletin. STEERING; PARKING BRAKE; WHEELS. Leather Steering Wheel Has Loose Material Poor Appearance
08074212023-01-17. Service bulletin. WHEELS; SEAT BELTS; STEERING. UGQ, UGV, UJV and UJQ Radio Enhancements This bulletin involves inspecting the software level to see if the radio needs oneor two USB flash drive(s) to update the radio software level to 39.2. Customers may experience one or more of the following: Voice recognition (VR) fails while road names are written in Catalan. After the update to software level MR-28.31, the Amperometer inside Jeepskills shows values too high. The radio may lose some or all programmed presets. Volume blocked/uncontrollable. Heating Steering wheel and seat SK greyed out. Eco Drive trips saved issue. Radio may reset, turn itself off and then back on again. Radio display screen lock up. Park assist chime will continue to chime after the vehicle is turned off. Frequent pop-ups during startup saying device not connected - Uconnect LIVE. Radio will display the incorrect speed limit in kph when approaching a roadspeed camera(2018 WK Only). Uconnect Live Apps restricted to only MyCar, ecoDrive and Jeep Skills(2018 WK Only). Russian language missing in the radio setting menu(2018 WK with UGQ Only). If the radio is set for Russian language, UConnect displays unknown symbolson the ?Off Road Page?(2018 WK with UGQ Only). Could not disable the feature for the heated seat and heated steering wheelturned on automatically at startup(2018 WK with UGQ Only). In addition the following enhancements are included: Navigation improvements. Bluetooth improvements. VR improvements. Russian language enhancements (2018 WK with UGQ Only)
90041632023-01-17. Service bulletin. PARKING BRAKE; VEHICLE SPEED CONTROL; WHEELS. MOLDING, Wheel Flare, Quarter Panel (Wide wheel flares) If you have a Jeep Grand Cherokee Summit, SRT, Trackhawk or Limited X with wide flares that are loose appearing or poor fitting, please document the VIN and provide the following information: 1.) Take image of customer concern - Highlighting flare adhesive surface location where the misaligned/loose/delamination condition is found with respect to the door or body. 2.) Email images of concerns to FCA Redacted Content For additional questions, call FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S22080000622023-01-09. Service bulletin. STEERING; WHEELS. Heated Steering Wheel Does Not Operate
91000952022-12-12. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; WHEELS. Alternator Assy Prior to alternator removal: 1. Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section "System Operation - Smart Charging System". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts to QEC for analysis.
91000822022-11-07. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; WHEELS; EQUIPMENT; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:STARTER ASSEMBLY:SOLENOID. STARTER, Engine Prior to starter removal: 1. Inspect and check all connections to the starter motor solenoid a. Unplug and plug-in the T50 1-way connector as needed to verify the connection is good & tight and check for any bent pin in the connection. b. Inspect the T30 connection (i.e. B+ M8 threaded stud & nut) for tightness to assure cable ring terminal connection is secured and tight (use torque spec per service manual). 2. Check/verify all grounds in the cranking circuit a. Check tightness of mounting bolts that secure starter to the engine block b. Check main ground from engine to chassis c. Check battery ground cable connections are clean and tight d.Potentially, loosen both starter motor bolts, without removing, and re-tighten to torque specifications in the service manual e. After all steps above are complete, attempt to crank the engine to verify if improvement has been made (i.e. the steps fixed the customer complaint) 3. Conduct the voltage drop test (starter feed circuit) per the service manual before removing the starter motor 4. Starter Removal: conduct the removal if above steps do not fix the complaint a. Conduct bench test by applying 12 volts to motor T30 and T50 connections (i.e. conduct simple free speed test) b. Free speed test should result in starter motor pinion travel to pinion stop and rotation with normal rotational noise (i.e. no grinding, scrapping, etc.) c. If any abnormal noise is present, replace the starter motor 5. During starter removal, also remove and replace the two starter mounting bolts. Return the bolts with starter motor for analysis at QEC and the supplier warranty analysis lab.
91000142022-10-31. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); TIRES; SUSPENSION; STEERING; STEERING:RACK AND PINION; WHEELS. GEAR Rack And Pinion You must order New service unique steering gear to service the following configurations, PN: 68624835A$ WK: (3.6 or 3.0) w Sport Suspension w 265/50R20 BSW 3 SEASON PERF TIRES or 265/50R20 BSW All Season Tires
0805022REVA2022-10-17. Service bulletin. VISIBILITY; WHEELS; PARKING BRAKE; VEHICLE SPEED CONTROL; STRUCTURE; ELECTRICAL SYSTEM; STEERING; FUEL SYSTEM, GASOLINE. Flash: Body Control Module (BCM) Updates This bulletin involves reprogramming the Body Control Module (BCM) with the latestavailable software. Customer may describe various LIN related functions (steering wheel, center stack, terrain or 4wd) switchesand/or certain interior lamps not working. Upon further inspection the technician may also observe the following DTCs may have set withouta MIL: U1223-00 - Lost Communication with Wireless Charging Pad Module. U121E-00 - Lost Communication With Steering Wheel Cruise Control Switch. U1207-00 - Lost Communication With Terrain Switch Bank Module. U1191-00 - Lost Communication with Switch Bank Module 2. U1153-00 - Lost Communication With Windshield Wiper Smart Module. U114F-00 - Lost Communication with LIN Overhead Console. U114D-87 - Lost Communication with Hands Free Liftgate Module-Missing Message. U113B-00 - Lost Communication With Switch Bank Module. U112D-00 - Lost Communication With EVIC Steering Wheel Switches. U1125-00 - Lost Communication With LIN ECU 5- (Ride Height Switch Module). U1123-00 - Lost Communication With LIN ECU 3- (Switch Bank Module Rear Right). U1122-00 - Lost Communication With LIN ECU 2- (Switch Bank Module Rear Left). U1008-00 - LIN 1 Bus Steering Column Control Module Electrical Diagnostic. U0231-00 - Lost Communication With Rain Sensing Module. In addition, the customer may experience one or more of the following:Fuel Level and Range (distance to empty) (DTE) will both increase aftersleep cycle. Fuel Level % would increase when parked on a slope. Fuel gauge remains at full for 107 km (67 miles) vs. 73 km (45 miles). After fueling up with 68 liters (18.1 gallons) of fuel, the fuel gauge onlywill read around 1/4 tank and the low fuel lamp is still illuminated. After 10 minutes of driving, the gauge only read around 3/4 tank andthe fuel lamp is still on. Refuel button is pressed for a short duration of 500ms or less at key off,
90041632022-10-17. Service bulletin. WHEELS. MOLDING, Wheel Flare, Quarter Panel (Wide wheel flares) If you have a Jeep Grand Cherokee Summit, SRT, Trackhawk or Limited X with wide flares that are loose appearing or poor fitting, please document the VIN and provide the following information: 1.) Take image of customer concern - Highlighting flare adhesive surface location where the misaligned/loose/delamination condition is found with respect to the door or body. 2.) Email images of concerns to FCA Redacted Content For additional questions, call FCA Redacted Content. If no response in 15 minutes, proceed with repair.
90041632022-10-17. Service bulletin. WHEELS; PARKING BRAKE; VEHICLE SPEED CONTROL. MOLDING, Wheel Flare, Quarter Panel (Wide wheel flares) If you have a Jeep Grand Cherokee Summit, SRT, Trackhawk or Limited X with wide flares that are loose appearing or poor fitting, please document the VIN and provide the following information: 1.) Take image of customer concern - Highlighting flare adhesive surface location where the misaligned/loose/delamination condition is found with respect to the door or body. 2.) Email images of concerns to FCA Redacted Content For additional questions, call FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S22080000622022-10-17. Service bulletin. STEERING; WHEELS. Heated Steering Wheel Does Not Operate
90043632022-09-26. Service bulletin. ENGINE AND ENGINE COOLING; WHEELS. MOTOR, Blower with Wheel Blower motor making noise. Upon removing blower motor, inspect HVAC case for damage in the blower wheel area. Please call FCA Redacted Content to report findings. If no response in 15 minutes, proceed with repair.
S22080000622022-09-26. Service bulletin. STEERING:STEERING WHEEL /HANDLE BAR:HAND HEATER/COOLER; WHEELS; STEERING. Heated Steering Wheel Does Not Operate
90041632022-07-18. Service bulletin. WHEELS; PARKING BRAKE; VEHICLE SPEED CONTROL. MOLDING, Quarter Panel (Wide wheel flares) If you have a Jeep Grand Cherokee Summit, SRT, Trackhawk or Limited X with wide flares that appear to be loose or poor fittting, please document the VIN and provide the following information: 1.) Take image of customer concern - Highlighting flare adhesive surface location where the misaligned/loose condition is found with respect to the door or body. 2.) Email images of concerns to FCA Redacted Content. For additional questions, call FCA Redacted Content. If no response in 15 minutes, proceed with repair.
90041632021-06-28. Service bulletin. WHEELS. MOLDING, Wheel Flare, Quarter Panel (Wide wheel flares) If you have a Jeep Grand Cherokee Summit, SRT, Trackhawk or Limited X with wide flares that are loose appearing or poor fitting, please document the VIN and provide the following information: 1.) Take image of customer concern - Highlighting flare adhesive surface location where the misaligned/loose/delamination condition is found with respect to the door or body. 2.) Email images of concerns to FCA Redacted Content For additional questions, call FCA Redacted Content. If no response in 15 minutes, proceed with repair.
90043632021-05-24. Service bulletin. ENGINE AND ENGINE COOLING; WHEELS. MOTOR, Blower with Wheel Blower motor making noise. Upon removing blower motor, inspect HVAC case for damage in the blower wheel area. Please call FCA Redacted Content to report findings. If no response in 15 minutes, proceed with repair.
90041632021-02-16. Service bulletin. WHEELS. MOLDING, Quarter Panel (Wide wheel flares) If you have a Jeep Grand Cherokee Summit, SRT, Trackhawk or Limited X with wide flares that appear to be loose or poor fittting, please document the VIN and provide the following information: 1.) Take image of customer concern - Highlighting flare adhesive surface location where the misaligned/loose condition is found with respect to the door or body. 2.) Email images of concerns to FCA Redacted Content. For additional questions, call FCA Redacted Content. If no response in 15 minutes, proceed with repair.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.