WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Infiniti QX60

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

262 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
ITB15021A2021-05-10. Service bulletin. EQUIPMENT; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP. SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
ITB160132021-05-10. Service bulletin. ENGINE AND ENGINE COOLING. IF YOU CONFIRM The MIL is ON with P0116 Engine Coolant Temperature (ECT SENSOR) stored, and There are no drivability issues. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm if ECM reprogramming applies. 2. If it applies, reprogram the ECM. See this bulletin for further detail.
ITB160112021-05-10. Service bulletin. STEERING. IF YOU CONFIRM While turning the steering wheel or when driving at low speed (straight or turning), a high pitch power steering noise can be heard. * Only while seated inside the vehicle And * With all of the windows up NOTE: If the audio and/or HVAC systems are turned ON it may be difficult to hear this issue. ACTION Install Insulator onto power steering oil pump assembly with Service Procedure starting on next page. Please see this bulletin for further details.
ITB03051J2021-05-10. Service bulletin. EXTERIOR LIGHTING. SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Infiniti?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
ITB160062021-05-10. Service bulletin. FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: SONAR/ULTRASONIC; EQUIPMENT. SERVICE INFORMATION When diagnosing the front sonar parking sensor for potentially unwanted activation (e.g. sonar activates with no obstacle ahead), inspect the front license plate, front license plate frame and if equipped, the front license plate bracket. See page 2 for example photos. The front sonar parking sensor may activate if: The front license plate is bent outward from its bracket (there is a gap between the license plate and the bracket) OR the front license plate frame is bent or loose and is hanging outward, away from the license plate and/or bracket (there is a gap between the license plate frame and the license plate and/or bracket) OR the bracket is loose and is hanging outward, away from the bumper (there is a gap between the bracket and the bumper). If any of these conditions are found, correct it by removing the gap (straighten the license plate, straighten and/or secure the license plate frame, or secure the bracket, as it applies). - Retest the operation of the front sonar parking sensor. If the issue is not resolved, go to ASIST and the related Electronic Service Manual (ESM) for further diagnosis. See this bulletin for further detail.
ITB16007A2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION On Applied Vehicles, the torque specification for the rear final drive assembly rear mounting stud has been revised. New torque specification: 71 N-m, 7.2 kg-m, 52 ft-lbs Use the torque specification shown above when installing a rear final drive assembly. At a later date and where possible, the applicable Electronic Service Manuals will be updated with the revised specification. See this bulletin for further detail.
ITB160092021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION The function to detect the last item to trigger the vehicles theft alarm system can now be accessed with CONSULT-III plus (C-III plus). This function can be accessed by selecting: * Diagnosis (All Systems) or Diagnosis (One System). Then * BCM Then * THEFT ALM Then * Work Support Then * THEFT ALM TRG See this bulletin for further details.
ITB160052021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION The Intelligent Keys used on the various Infiniti vehicles may not be interchangeable between models and years. See this bulletin for further detail.
ITB150322021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further detail.
ITB09015G2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.
ITB14059A2021-05-10. Service bulletin. VEHICLE SPEED CONTROL; PARKING BRAKE; SEAT BELTS. IF YOU CONFIRM All "hands free" functions of the Intelligent Key (I-Key) do not work. For example, the doors will not lock or unlock when pressing either front door request switch. NOTE: - The issue of all I-Key "hands free" functions not working may occur intermittently or all the time. - The message "No Key Detected" or similar may show on the Vehicle Information Display (located in the combination meter). - All I-Key remote button functions (door lock/unlock, etc.) WILL work normally when all I-Key "hands free" functions are NOT working. ACTION 1. Inspect the I-Key?s battery on its negative contact side. 2. If excessive scratching is found, replace the battery. 3. Verify all I-Key functions (both "hands free" and remote) work properly after battery replacement. NOTE: Do NOT replace the BCM, I-Key, or other parts for the issue described under IF YOU CONFIRM, if it should occur. See this bulletin for further detail.
ITB11042D2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.
ITB14016B2021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM All of the following - The engine will not start (no crank; starter will not engage) when pushing the ignition switch, and I-Key Error message is displayed in the combination meter, and DTC B2604 (PNP/Clutch Switch) is stored, past or present. ACTION Perform adjustment of the shift control cable per the Service Procedure in this bulletin. See this bulletin for further detail.
ITB13039A2021-05-10. Service bulletin. BACK OVER PREVENTION; WHEELS; SERVICE BRAKES; LANE DEPARTURE. SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
ITB13049A2021-05-10. Service bulletin. PARKING BRAKE. IF YOU CONFIRM: The rubber weatherstrips on either one of the roof side molding assemblies (moldings) is coming loose from the molding itself. ACTION: Replace both left and right moldings with the ones listed in PARTS INFORMATION. - Refer to SERVICE PROCEDURE for molding replacement. See this bulletin for further detail.
ITB14028A2021-05-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT. SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
ITB10017D2021-05-10. Service bulletin. EQUIPMENT:ELECTRICAL. SERVICE INFORMATION If the AV Control Unit needs to be replaced on an Applied Vehicle for any reason, follow the steps in the Service Procedure to configure the Multi AV system. NOTE - The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control Unit until instructed. See this bulletin for further detail.
ITB14051A2021-05-10. Service bulletin. POWER TRAIN; FORWARD COLLISION AVOIDANCE. IF YOU CONFIRM All of the following: The FCW (Forward Collision Warning) malfunction is ON or reported to have been ON, and DTC C1A27 (ECD POWER SUPPLY CIRCUIT) is stored (Past or Current), and the brake fluid level is normal. NOTE: C1A27 is an ICC (Intelligent Cruise Control) DTC. ACTION Reprogram the ABS control unit (ABS) per the Service Procedure in this bulletin. - Part of the Service Procedure, step 20 on page 8, is a confirmation that reprogramming is needed to resolve the incident shown in Figure A and B on page 1. See this bulletin for further detail.
ITB10037D2021-05-10. Service bulletin. VISIBILITY; AIR BAGS; STEERING. SERVICE INFORMATION The Applied Vehicles are equipped with a new version of Intelligent Key presets memory. Each Intelligent Key can be programmed to have its own unique set of presets for certain vehicle systems. Vehicle systems that are linked with Intelligent Key include: - Automatic Drive Positioner (includes driver seat, steering column, and mirror position memory) - Audio (station presets, etc.) - Auto air conditioning and heating (retains the last temperature and mode setting for each Intelligent Key user) - Navigation system (retains the last settings [e.g., Birdview] and clock display preference for each Intelligent Key user) See this bulletin for further detail.
ITB150252021-05-10. Service bulletin. BACK OVER PREVENTION; EQUIPMENT; WHEELS; SERVICE BRAKES; STEERING. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
ITB150242021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
ITB12072C2021-05-10. Service bulletin. SUSPENSION. IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle when making turns on dry roads at low speeds (under 40 MPH), and it does not occur if the Electric Controlled Coupling is electrically disconnected. ACTION Replace the Electric Controlled Coupling for the rear final drive. See this bulletin for further detail.
ITB150202021-05-10. Service bulletin. WHEELS. SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
ITB150142021-05-10. Service bulletin. EQUIPMENT. IF YOU CONFIRM The vehicle has been operated in cold weather, below approximately -18ºC (0ºF), and AWD ERROR is displayed in the Vehicle Information Display, and DTC C1204 (AWD Solenoid) is stored. ACTION Replace the AWD Control Unit with the one listed in the Parts Information of this bulletin. See this bulletin for further detail.
ITB10062E2021-05-10. Service bulletin. WHEELS. SERVICE INFORMATION For vehicles delivered to the dealers with wheel protector covers - Do not remove the wheel protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.