Service bulletin ITB16011
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10192762 |
| Published by NHTSA | 2021-05-10 |
| Manufacturer's number | ITB16011 |
| Manufacturer's date | 2016-03-08 |
| NHTSA component | STEERING |
NHTSA's summary
IF YOU CONFIRM While turning the steering wheel or when driving at low speed (straight or turning), a high pitch power steering noise can be heard. * Only while seated inside the vehicle And * With all of the windows up NOTE: If the audio and/or HVAC systems are turned ON it may be difficult to hear this issue. ACTION Install Insulator onto power steering oil pump assembly with Service Procedure starting on next page. Please see this bulletin for further details.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Steering
| INFINITI JX | 2013 |
|---|---|
| INFINITI QX60 | 2014, 2015 |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| ITB10037D | 2021-05-10. Service bulletin. SERVICE INFORMATION The Applied Vehicles are equipped with a new version of Intelligent Key presets memory. Each Intelligent Key can be programmed to have its own unique set of presets for certain vehicle systems. Vehicle systems that are linked with Intelligent Key include: - Automatic Drive Positioner (includes driver seat, steering column, and mirror position memory) - Audio (station presets, etc.) - Auto air conditioning and heating (retains the last temperature and mode setting for each Intelligent Key user) - Navigation system (retains the last settings [e.g., Birdview] and clock display preference for each Intelligent Key user) See this bulletin for further detail. |
|---|---|
| ITB15025 | 2021-05-10. Service bulletin. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail. |
| ITB00024F | 2021-05-10. Service bulletin. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. See this bulletin for further details. |
| ITB04038A | 2021-05-10. Service bulletin. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see ITB00-024). See this bulletin for further detail. |