WenmarOpen by Wenmar Pro

Service bulletins for the 2007 Infiniti QX56

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

98 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
ITB10058A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; ENGINE. IF YOU CONFRIM An oil leak at the right side block ball plug behind the alternator. ACTION: Use a punch to seat the block ball plug in the hole (refer to the Service Procedure). See this bulletin for further detail.
ITB10029A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
ITB08024C2021-05-10. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
ITB09012F2021-05-10. Service bulletin. FUEL/PROPULSION SYSTEM; EQUIPMENT. SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Infiniti vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.
ITB92069D2021-05-10. Service bulletin. EQUIPMENT; WHEELS. Infiniti Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Infiniti design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Infiniti's standards. Infiniti Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Infiniti most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletin for further details.
ITB13006A2021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulletin for further details.
ITB00024F2021-05-10. Service bulletin. STEERING; SUSPENSION; SERVICE BRAKES. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. See this bulletin for further details.
ITB04038A2021-05-10. Service bulletin. SERVICE BRAKES; STEERING; WHEELS. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see ITB00-024). See this bulletin for further detail.
ITB98011F2021-05-10. Service bulletin. ELECTRICAL SYSTEM. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
ITB99001A2021-05-10. Service bulletin. SUSPENSION. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
ITB11014B2021-05-10. Service bulletin. STRUCTURE. SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.
ITB17-042D2021-04-13. Service bulletin. ENGINE AND ENGINE COOLING. INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-006A2021-04-08. Service bulletin. ELECTRICAL SYSTEM. INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB11-003F2021-04-08. Service bulletin. ELECTRICAL SYSTEM. NAVIGATION MAP DATA UPDATE MATRIX This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-024a2021-01-09. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). 2005-2015 INFINITI VEHICLES; ECM REPROGRAMMING SERVICE INFORMATION This bulletin is no longer active. Please discard previous versions of ITB15-024.
ITB10-055a2021-01-08. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. QX56; REVISED UPPER OIL PAN AND TIMING CHAIN CASE PROCEDURES This bulletin is no longer active. Please discard previous versions of ITB10-055.
ITB07-018a2020-11-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. VOLUNTARY SERVICE CAMPAIGN 2007 QX56; CONDENSER FAN Service Campaign ID # P7216 is no longer active. • Repair orders opened after this bulletin’s published date are no longer eligible for reimbursement under Campaign ID # P7216. • Please discard all previous versions of ITB07-018.
ITB17-042c2020-10-08. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; EQUIPMENT. INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB20-0192020-09-11. Service bulletin. ENGINE AND ENGINE COOLING. VK56 CONNECTING ROD CAP BOLT SERVICE INFORMATION SERVICE INFORMATION A change has been made to the connecting rod cap bolt service part. The new service part (B in Figure 1) is visually different, but is a direct replacement for the original equipment part. IMPORTANT: See page 2 for the procedure to inspect the cap bolt service part for excessive stretch. If replacement of a single connecting rod cap bolt is indicated for any given connecting rod, both connecting rod cap bolts of the affected connecting rod must be replaced as a set.
DOR-M9J4S-072020-07-27. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
DOR-M3J3F-072020-07-27. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
ITB19-0082019-05-20. Service bulletin. EQUIPMENT. EXTERIOR CLEANING INFORMATION SERVICE INFORMATION When cleaning the exterior of an Infiniti vehicle, damage may occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.
ITB17-042b2019-02-19. Service bulletin. ENGINE AND ENGINE COOLING. INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
Revision 1-IEVAP2019-01-07. Service bulletin. ENGINE; EQUIPMENT. OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.
ITB17-026b2019-01-07. Service bulletin. FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, GASOLINE. INFINITI; FUEL TANK IS EXTREMELY DIFFICULT TO FILL The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.