WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Infiniti Q60

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

188 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
ITB13-052b2018-05-07. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
ITB18-0102018-03-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. INFINITI; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Infiniti Warranty Flat Rate Manual and submit a claim for the repairs performed.
ITB18-0052018-03-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION SERVICE INFORMATION If the following ICC/ADAS codes are stored, make sure to follow the diagnostic procedures in the Electronic Service Manual (ESM) before replacing any parts. C1A03 ? VEHICLE SPEED SENSOR -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1A04 ? ABS/TCS/VDC SYSTEM -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1B01 CAM AIMING INCMP -The diagnostic procedure in the ESM includes check and, if needed, repair for LANE CAMERA DTCs before replacing ADAS components. -LANE CAMERA DTC may require adjustment of the lane camera. -If repairs/adjustments are performed for the Lane Camera; when compete, perform DTC Confirmation Procedure again before doing any additional repairs.
ITB13-026h2018-03-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. The Applied Vehicles section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB18-0032018-02-21. Service bulletin. EQUIPMENT:OTHER:LABELS. REDUCED VEHICLE LOAD CAPACITY LABEL (REGULATORY REQUIREMENT) This bulletin applies to vehicles equipped with dealer installed or VPC installed accessories. SERVICE INFORMATION The National Highway Traffic Safety Administration (NHTSA) requires that any automobile dealer that installs accessories on a vehicle prior to first retail sale must install a special label (?reduced capacity label?) on that vehicle if the total weight of all accessories on that vehicle exceeds 1.5 percent of the vehicle?s gross vehicle weight rating (GVWR) or 100 pounds, whichever is less. This includes accessories that the dealer installs (dealer installed factory accessories and dealer installed aftermarket accessories), and accessories installed at the Vehicle Processing Center (VPC) prior to the vehicle being delivered to the dealer. IMPORTANT: Failure to comply with this requirement may result in penalties imposed by NHTSA. Follow the instructions in this bulletin to help meet these requirements.
ITB12-011j2018-02-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). TELEMATICS SERVICE INFORMATION This bulletin has been amended. A correction was made to the Service Procedure on page 15. No other changes were made. Please discard previous versions of this bulletin.
ITB17-0552018-01-29. Service bulletin. EQUIPMENT. INFINITI; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin applies to vehicles equipped with Intelligent Key only. SERVICE INFORMATION When replacing or adding an Intelligent Key, it is very important to make sure the correct Intelligent Key is selected from the parts department. - A running change was made that will help identify the correct Intelligent Key. - Beginning in late 2017 and early 2018 the last five digits of the Intelligent Key part number is marked on the Intelligent Key under the mechanical key. - See page 2 for location images of this part number addition. NOTE: - A correct Intelligent Key may or may not have the last five digits of the part number as shown on page 2. - The above running change was applied as a ?help? to identify the correct Intelligent Key for a given vehicle, but the actual part number listed in the parts catalog did not change. - Make sure to use the electronic parts catalog (FAST) or equivalent to confirm the correct Intelligent Key for a given vehicle.
ITB17-0542018-01-29. Service bulletin. ENGINE AND ENGINE COOLING. 2016-2018 Q50 AND 2017-2018 Q60; CHARGE AIR COOLER COOLING SYSTEM SERVICE INFORMATION This bulletin applies to vehicles equipped with VR30DDTT V6 engine. SERVICE INFORMATION Whenever either or both charge air coolers (intercooler) on an applied vehicle?s VR30DDTT V6 engine is removed and reinstalled/replaced for any reason, make sure to properly bleed the charge air cooler (intercooler) cooling system. Use the SERVICE PROCEDURE in this bulletin for the proper intercooler cooling system bleeding. - The procedure in this bulletin is different than what is currently in the Electronic Service Manuals (ESMs). - The ESMs will be updated at a later date. CAUTION: If the intercooler cooling system bleeding procedure in this bulletin is not used: - Damage may occur to the intercooler electric water pump(s), AND/OR - One or more of the following DTCs may set: - P14A2, P14A3, P14A4, P14A5, P14A6, P14A7, P14A8, P14A9 - P14AA, P14AC P14AD, P14AE, P14AF - P14B0, P14B1, P14B2, P14B3, P14B5
ITB17-009a2018-01-29. Service bulletin. VISIBILITY:GLASS, SIDE/REAR. WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended to apply to the latest models and model years, and warranty information on page 2 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB12-011i2018-01-29. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with factory Navigation system. This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard all previous versions of this bulletin.
ITB09-039e2018-01-29. Service bulletin. VISIBILITY:WINDSHIELD. WINDSHIELD CRACKING This bulletin has been amended to apply to the latest models and model years. Also, warranty information on pages 1 and 8 has been updated. No other changes have been made. Please discard previous versions of this bulletin.
ITB00-024g2018-01-29. Service bulletin. SERVICE BRAKES. BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR This bulletin has been amended to include vehicles built up to the publication date. Also, tips for using the ProCut? brake lathe were added on page 8, and a Brake Noise Diagnostic Worksheet was added on page 10. Please discard previous versions of this bulletin.
ITB17-0582018-01-29. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. INTRODUCTION Infiniti is conducting this voluntary emission recall campaign on certain specific model year 2016-2018 Q50 and 2017 Q60 vehicles. The Engine Control Module (ECM) will be reprogrammed so that in the event of an automatic transmission diagnostic issue, the diagnosis signals will be communicated properly and a Malfunction Indicator Light (MIL) will be properly illuminated to notify the driver. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification number R1726 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer?s responsibility to check Service Comm or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer?s inventory.
ITB17-0602018-01-29. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. INFINITI; INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE SERVICE INFORMATION When the initialization procedure being performed with a new or existing Intelligent Key to an applied vehicle is interrupted (the procedure stops or will not continue), the BCM may be left in learn mode and will not function until it returns to normal mode. Under this condition, the BCM and Intelligent Key(s) will not function normally. If this condition occurs, the BCM must be returned to normal mode and the initialization procedure started over. To get back to the beginning of the Initialization procedure, use one of the following procedures: - Successfully perform the initialization procedure using one of the original Intelligent Keys twice consecutively. - Each successful initialization will follow with two (2) quick tones. OR - When the initialization procedure cannot be successfully performed twice (more than two quick tones), perform the initialization procedure five (5) times using the inoperative ?failed? Intelligent Key. - Initialization does not need to be successful when performed five times. When returning to normal operating mode, the initialization procedure for all Intelligent Keys may be started again.
ITB13-026g2018-01-29. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. The Applied Vehicles section and Part 1 of the Service Procedure have been revised. No other changes have been made. Please discard previous versions of this bulletin.
ITB16-0412017-10-25. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. 2017 Q60; SUNROOF INOPERATIVE IF YOU CONFIRM The sunroof is inoperative (will not open and/or close electrically). ACTION 1. Turn the ignition OFF. 2. Wait at least 1 minute. 3. Disconnect both battery cables, negative first. 4. Wait at least 30 seconds. 5. Reconnect both battery cables, positive and then negative. 6. Recheck the sunroof for proper operation. - If the sunroof is still electrically inoperative, refer to the Electronic Service Manual (ESM), section RF ? Roof for further diagnosis. 7. Reset/reinitialize systems as needed. - Refer to the Electronic Service ESM, section PG ? Power Supply Ground & Circuit Elements, for a listing of systems that require reset/initialization after reconnecting the 12 V battery. - Look in the PG section index for ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL. - This list often includes items such as radio, power windows, clock, sunroof, etc.
ITB12-011g2017-10-25. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. TELEMATICS SERVICE INFORMATION This bulletin has been amended. Modifications have been made to include 2017 Q50, Q60, Q70, QX60, and QX80 vehicles. No other changes have been made. Please discard all previous versions of this bulletin.
ITB16-0472017-10-15. Service bulletin. ENGINE. INFINITI; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
ITB16-0462017-10-15. Service bulletin. WHEELS. ESM CORRECTIONS FOR FRONT WHEEL ALIGNMENT SPECIFICATIONS SERVICE INFORMATION For the Applied Vehicles listed above, some front wheel alignment specifications listed in the Electronic Service Manual (ESM), section FSU-Front Suspension, were listed incorrectly and have been corrected. - Updated ESMs will be distributed to the field as quickly as possible. - Until the updated ESMs are made available, please use the corrected specifications listed in this bulletin. - Specification areas that have corrections are outlined with a Red box on the following pages.
ITB16-0442017-10-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. 2016-2017 Q50, 2017 Q60, AND 2017 QX30 WITH 2.0L TURBO ENGINE; CARTRIDGE-STYLE OIL FILTER SERVICE INFORMATION - The Applied Vehicles are equipped with a cartridge-style oil filter. - The filter may be difficult to remove. If this should occur, pull the filter straight off with no bending (if the filter rotates with the housing). - The filter housing may be damaged or broken if not handled with care. - If the filter housing is damaged or broken, it must be replaced. NOTE: - If the tip of the filter housing breaks off inside the front cover of the engine, use needle-nose pliers to remove the piece(s) to prevent debris from entering the oil passages when the engine is started. - If a replacement filter housing is needed, make sure to lubricate the o-rings and neck of the filter housing prior to installation.
ITB16-042a2017-10-15. Service bulletin. VISIBILITY. 2014-2017 Q60 AND Q50; POWER WINDOWS DO NOT OPERATE CORRECTLY SERVICE INFORMATION If power is interrupted to the power window system, it may cause one or more of the following symptoms to occur on one or more power windows: - AUTO-UP does not work, but window will move up and down with manual operation of the switch. - When door is opened (only applies to Q60), window will lower a small amount (normal operation) but will not raise when door is closed. - Window will move down when operating the window switch, but will not move up. NOTE: - If any of the above symptoms should occur, it may indicate that Window Initialization is needed (see page 2). Initialization should be done before attempting any repairs. - If needed, refer to the applicable Electronic Service Manual (ESM) to perform electrical diagnosis. - After electrical repairs to the vehicle (including repairs to the power windows), make sure to perform the Window Initialization and Anti-pinch Function Check procedures on page 2.
ITB13-052a2017-10-15. Service bulletin. ENGINE. INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
ITB13-026f2017-10-15. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. Modifications have been made to include 2017 Q50, Q50 Hybrid, Q60, QX30, QX60 and QX60 Hybrid vehicles. No other changes have been made. Please discard all previous versions of this bulletin.
ITB17-036a2017-10-15. Service bulletin. ENGINE. 2016-2017 Q50 AND 2017 Q60; ENGINE STOPS RUNNING, MIL ON WITH DTC STORED This bulletin has been superseded by ITB17-044. VOLUNTARY SAFETY RECALL CAMPAIGN 2016-2017 Q50 AND 2017 Q60 WITH 2.0L TURBO ENGINE; FUEL PUMP CONTROL MODULE Please discard previous versions of this bulletin.
ITB09-015h2017-10-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. 12 VOLT BATTERY STORAGE AND MAINTENANCE FOR NEW VEHICLES IN RETAILER INVENTORY This bulletin has been amended throughout. Please discard all previous versions of this bulletin.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.