WenmarOpen by Wenmar Pro

Service bulletins for the 2020 Ford Transit

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

177 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Driver assistance are shown. Show all

Bulletins, newest first
SSM 547202026-04-10. Service bulletin. ELECTRICAL SYSTEM; LANE DEPARTURE: BLIND SPOT DETECTION. Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
25N172026-03-27. Other. LANE DEPARTURE: BLIND SPOT DETECTION; BACK OVER PREVENTION: WARNINGS; BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING; UNKNOWN OR OTHER. Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
SSM 543132025-10-28. Service bulletin. LANE DEPARTURE: BLIND SPOT DETECTION; ELECTRICAL SYSTEM. Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
TSB 23-21542023-05-23. Service bulletin. BACK OVER PREVENTION:SOFTWARE; POWER TRAIN. 2021-2022 F-150 vehicles with 2.7L, 3.3L, 3.5L EcoBoost or 5.0L engines, 2020-2022 Transit vehicles with 3.5L Duratec/3.5L EcoBoost engines, 2021-2023 Bronco with the 2.3L or 2.7L engine having charging system diagnostics performed in the Workshop Manual (WSM) may experience the generator voltage desired (GENVDSD) parameter identification (PID) missing from the powertrain control module (PCM) PID list in the Ford Diagnosis And Repair System (FDRS) scan tool. This may be due to a software parameter in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM.
SSM 506592022-04-13. Service bulletin. BACK OVER PREVENTION; EQUIPMENT; ELECTRICAL SYSTEM. Some 2017-2022 Transit Connect/Transit/Explorer vehicles equipped with a fleet telematics global positioning system (GPS) and a connected human machine interface (HMI) radio (CHR) may experience concerns with rear camera zoom, wrong map matching or a blank display. If these concerns are present, it's likely to be a software issue caused by the audio control module (ACM) that can be remedied by updating the ACM software to the latest level with the FDRS application. If the update does not resolve the concern, refer to the Workshop Manual. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 497562021-05-03. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Some 2018-2021 vehicles supported by FDRS may not list a software update for a module under the SW Updates tab although an SSM or TSB is published for a software update. This may be due to the module already being at the latest software level. A later software level may have been programmed at the assembly plant, during a previous dealer visit or by an over the air (OTA) update for vehicles that have automatic updates enabled in the SYNC system settings. To review a vehicle's OTA update history, visit the Connected Vehicle > OTA Dashboard tab in OASIS. Information about the OTA Dashboard can be found on FMCDealer.com when performing a search on OTA History Job Aid.
20B392020-12-05. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:ADAS:HUD:CAMERA/SENSOR. Certain 2020 Model Year Multiple Vehicle Lines Front View and Center High Mount Stop Lamp Camera Improper Function In some of the affected vehicles, insufficient electrical conductivity within the Printed Circuit Board (PCB) internal to the camera may lead to intermittent front view or Center High Mount Stop Lamp (CHMSL) camera operation. This could result in a blank or distorted image from the front of the vehicle or of the truck bed Dealers are to replace the front view camera or the CHMSL camera following the dealer bulletin technical information. This service must be performed on all affected vehicles at no charge to the vehicle owner.
SSM 493142020-12-04. Service bulletin. FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; ELECTRICAL SYSTEM. Some 2020 Transit vehicles built on 31-Jul-2020 and through 14-Aug-2020 may experience a forward collision warning light with diagnostic trouble codes (DTC) B1433:54 and U2100:00 set in the cruise control module (CCM) due to being improperly equipped with a CCM. To verify, electrically disconnect the CCM. Once disconnected, perform a self-test on all other equipped modules. After a self test, start the vehicle to determine if the warning light is present. If other modules do not set loss of communication DTCs with the CCM and the warning light is no longer present, remove the CCM and seal/tape the connector to prevent water intrusion and relocate the harness to prevent rattles.
SSM 490332020-08-04. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; BACK OVER PREVENTION. Some 2020 F150/Nautilus/Expedition/Transit/Edge/Escape/Mustang vehicles built on or before 21-Jun-2020 may exhibit various front and/or rear parking aid camera concerns such as poor image quality, flickering and/or completely inoperative. If a vehicle exhibits this condition, replace the affected camera(s). Refer to Workshop Manual (WSM), Section 41313. For claiming, use causal part 19G490 and any applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
SSM 489592020-07-08. Service bulletin. LANE DEPARTURE. 2020 Transit, F-Super Duty, F-53 Motorhome/F-59 Commercial, 2021 F-650/F-750/E-series incomplete, chassis Cab, cutaway and stripped chassis vehicles equipped with a lane keeping or departure system are not calibrated from the factory to support final modifications. The final stage manufacturer is responsible for verifying that the lane keeping or departure system camera sensor is properly calibrated within Ford specifications once vehicles are completed. Calibrating the lane keeping or departure system utilizes the Ford scan tool to calibrate the front view camera. Refer to Workshop Manual (WSM) section 419-07. Do not submit a claim for this condition.
SSM 489152020-07-07. Service bulletin. LANE DEPARTURE. 2020 Transit, F-Super Duty, F-53 Motorhome/F-59 Commercial, 2021 F-650/F-750/E-series incomplete, chassis Cab, cutaway and stripped chassis vehicles equipped with a lane keeping or departure system are not calibrated from the factory to support final modifications. The final stage manufacturer is responsible for verifying that the lane keeping or departure system camera sensor is properly calibrated within Ford specifications once vehicles are completed. Calibrating the lane keeping or departure system utilizes the Ford FDRS scan tool to calibrate the front view camera. Refer to Workshop Manual (WSM) section 419-01. Do not submit a claim for this condition.
SSM 489542020-07-07. Service bulletin. ELECTRICAL SYSTEM; LANE DEPARTURE. 2020 Transit, F-Super Duty, F-53 Motorhome/F-59 Commercial, 2021 F-650/F-750/E-series incomplete, chassis Cab, cutaway and stripped chassis vehicles equipped with a lane keeping or departure system are not calibrated from the factory to support final modifications. The final stage manufacturer is responsible for verifying that the lane keeping or departure system camera sensor is properly calibrated within Ford specifications once vehicles are completed. Calibrating the lane keeping or departure system utilizes the Ford FDRS scan tool to calibrate the front view camera. Refer to Workshop Manual (WSM) section 419-07. Do not submit a claim for this condition.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.