WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Ford Taurus

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

75 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 489342020-07-07. Service bulletin. FORWARD COLLISION AVOIDANCE: WARNINGS. Some 2018-2019 Explorer/Expedition/F-150/F-Super Duty/Taurus vehicles equipped with a forward collision warning head up display (HUD) may exhibit various warning indicators caused by a possible intermittent lack of HS2-CAN network communication. If the concern cannot be duplicated, place the vehicle in direct sunlight for 15 to 30 minutes to increase the temperature of the HUD and retest. If the concern is present, disconnect the HUD and check for proper HS2-CAN network communication. If proper HS2-CAN network communication is achieved, then HUD module replacement is likely needed. If disconnecting the HUD does not re-establish communication, the HUD is not at fault, refer to Workshop Manual (WSM), Section 418-00, PPT AL for diagnostics.
SSM 487572020-05-04. Service bulletin. ELECTRICAL SYSTEM. Some customers may experience a notification in the FordPass and/or LincolnWay apps that indicates their vehicle has entered "deep sleep mode". This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".
SSM 486192020-04-02. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
SSM 484232020-01-08. Service bulletin. POWER TRAIN. Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 483402019-12-05. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
SSM 481352019-09-09. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 481232019-09-06. Service bulletin. ELECTRICAL SYSTEM. For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
SSM 480702019-08-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Use pigtail harness service part numbers 3U2Z-14S411-ZEA or CU2Z-14S411-FA, as both parts are interchangeable. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures.
TSB 19-22122019-08-07. Service bulletin. ENGINE AND ENGINE COOLING. Some 2018-2019 Explorer/Flex/Taurus/MKT vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power with diagnostic trouble codes (DTCs) P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure to replace the MAPT sensor.
TSB-22122019-08-06. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING. Some 2018-2019 Explorer/Flex/Taurus/MKT vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power with diagnostic trouble codes (DTCs) P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure to replace the MAPT sensor.
SSM 480532019-07-08. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section
SSM 480492019-07-08. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FORWARD COLLISION AVOIDANCE. Some 2015-2017 F-150/Mustang, 2015-2018 Edge/MKC, 2016-2018 MKX, 2013-2018 Explorer/Taurus/Flex/MKT, and 2017-2018 Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-21832019-07-03. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Some 2018-2019 Explorer/Flex/Taurus/MKT vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power with diagnostic trouble codes (DTCs) P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure steps to diagnose and replace the MAPT sensor.
SSM 479762019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 479672019-06-06. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 479482019-05-07. Service bulletin. ENGINE. SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 478502019-05-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 478242019-04-08. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 477972019-04-08. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
TSB 19-20512019-04-08. Service bulletin. EQUIPMENT; STRUCTURE. Some 2011-2019 Taurus/Police Interceptor Sedan vehicles may exhibit a loose and/or sagging headliner near the high mounted stoplamp. This may be caused by the headliner mounting bracket separating from the headliner. To resolve the condition, reapply adhesive to the headliner mounting bracket.
SSM 478242019-04-01. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 477972019-04-01. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ELECTRICAL SYSTEM. Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
TSB 19-20512019-04-01. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Some 2011-2019 Taurus/Police Interceptor Sedan vehicles may exhibit a loose and/or sagging headliner near the high mounted stoplamp. This may be caused by the headliner mounting bracket separating from the headliner. To resolve the condition, reapply adhesive to the headliner mounting bracket.
SSM 477492019-03-04. Service bulletin. EQUIPMENT. Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
SSM 477112019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.