WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Ford Mustang

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

167 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 478242019-04-01. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
TSB 19-20262019-04-01. Service bulletin. STRUCTURE. Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
SSM 477492019-03-04. Service bulletin. EQUIPMENT. Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
SSM 477112019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
TSB 18-23622019-03-04. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; EQUIPMENT. Some 2015-2017 Mustang vehicles may experience an inoperative rear parking aid camera, luggage compartment lamp, luggage compartment lid release and/or poor satellite radio reception. This may be due to damage to the 14A005 harness in the area of the right side luggage compartment lid hinge. This concern may be accompanied by diagnostic trouble codes (DTCs) B115E, C1001, and B1A89. Follow the Service Procedure steps to correct the condition.
TSB 18-23612019-03-04. Service bulletin. EQUIPMENT; SEATS. Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
SSM 476622019-01-07. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 476352019-01-07. Service bulletin. ELECTRICAL SYSTEM. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
SSM 475382018-12-03. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
SSM 475232018-12-03. Service bulletin. SERVICE BRAKES, HYDRAULIC. Some 2015-2018 Shelby GT350 and GT350R vehicles may require brake service or repairs to be performed. The vehicles should not have the brake rotors machined when servicing the brake system. Replacement of brake rotors is the only acceptable service of brake rotors on GT350 and GT350R vehicles. GT350 and GT350R vehicles are equipped with a brake system designed for high speed and superior fade resistance. Occasional brake squeal and elevated levels of brake dust may occur. This is normal and does not affect brake system performance. Refer to the Workshop Manual (WSM) Section 206-00 and the Mustang Owner's Manual and the Shelby GT350 Owner's Manual Supplement for further information.
TSB 18-23222018-11-19. Service bulletin. POWER TRAIN. Some 2015-2017 Mustang GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no DTCs present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has become loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. Follow the Service Procedure steps to correct the condition.
SSM 474892018-09-24. Service bulletin. STEERING. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
SSM 474442018-09-24. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
TSB 18-22562018-09-24. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2015-2017 Mustang vehicles may exhibit poor A/C performance. If the cause of this is found to be a refrigerant leak from the evaporator, it is recommended to replace only the evaporator as opposed to the entire climate control housing. Follow the Service Procedure steps to correct the condition.
SSM 474332018-09-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; EQUIPMENT. Some 2015-2017 Mustang vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with diagnostic trouble code (DTC) P0300 through P0308 present. A noticeable misfire may or may not accompany these DTCs. If normal diagnostics do not lead to a root cause for this concern, remove the intake manifold from the vehicle and verify the intake manifold runner control (IMRC) plates move when the IMRC actuators are moved by hand. These plates are visible through the outlet ports of the intake manifold. If the IMRC plates do not move when the IMRC actuators are moved by hand, the intake manifold should be replaced. For claiming, use causal part 9424 and applicable labor operations in Section 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 474292018-09-10. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2015 and 2016 Mustang vehicles built on or before 4/22/2016 may exhibit a partial outage of the rear tail, turn signal or stop lamps following a vehicle start with a low battery. This may be accompanied by any combination of DTCs B1271, B1272, B1273, B1274, B1275 and B1276. The condition typically clears on vehicle restart. Reprogram the BCMB module to the latest calibration using IDS release 110.01 or higher. Calibration files may also be obtained at www.motorcraftservice.com. Use applicable labor operations from Section 10 of the SLTS manual and use causal part 13C788.
SSM 473802018-07-23. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 473792018-07-23. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 473642018-07-23. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. Some 2015-2018 Mustang GT350s may exhibit an engine oil leak that appears to be originating from the oil filter adapter or oil cooler. If the leak appears to be originating from the oil cooler, be aware that the leak may actually be originating from the oil filter adapter, and oil may run down the oil cooler tubes and drip off of the cooler, making it appear that the leak is originating from the oil cooler. If the true source of the leak is caused by a damaged O-ring where the oil cooler tubes meet the oil filter adapter, be aware that these O-rings are now available as a separate service part from the oil cooler tubes. Replacement O-rings can be ordered using part number FR3Z-00815-A. For claiming, use causal part 6B850 and applicable labor operations in Section 6 of the Service Labor Time Standards (SLTS) Manual.
TSB18-21662018-07-23. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2015-2017 Mustang vehicles may exhibit poor A/C performance. If the cause of this is found to be a refrigerant leak from the evaporator, it is recommended to replace only the evaporator as opposed to the entire climate control housing. Follow the Service Procedure steps to correct the condition.
SSM 470412018-06-11. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 470122018-06-11. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal. It may be necessary to lightly tap around the stuck area of the clutch with a rubber mallet to free it from the pulley for removal. Refer to applicable labor operations from Section 11 of the SLTS maunual when replacing the A/C clutch.
SSM 469952018-06-11. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; STRUCTURE. Some 2015-2017 Mustang Convertibles built on or before 1-Feb-2017 may exhibit wear marks or damage to the exterior surface of the convertible top in the area of the front outer edges. This may be due to contact between the convertible top and the tonneau covers that may be installed on the vehicle by the customer when the top is in the open position. If the tonneau covers have been installed on the vehicle, and the wear/damage is located in the area where the tonneau covers overlap the convertible top, replace the convertible top material. Refer to WSM, Section 501-18. Discard the original tonneau covers, and supply the customer with new tonneau covers, part numbers FR3Z-7631004-CB and FR3Z-7631005-CB. For claiming, use causal part 7631004 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
SSM 470412018-05-29. Service bulletin. EQUIPMENT:ELECTRICAL. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 470122018-05-29. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal. It may be necessary to lightly tap around the stuck area of the clutch with a rubber mallet to free it from the pulley for removal. Refer to applicable labor operations from Section 11 of the SLTS maunual when replacing the A/C clutch.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.