Service bulletins for the 2023 Ford Maverick
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
121 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| SSM 52742 | 2024-08-06. Service bulletin. UNKNOWN OR OTHER. Some 2021-2023 F-150 hybrid vehicles equipped with a 3.5L PowerBoost engine and 2022-2023 Maverick full hybrid electric vehicles (FHEVs) may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2C22, P2C23, P237C, P237D, P237E and/or P237F in the powertrain control module (PCM). This may be due to the exhaust heat exchanger actuator. |
|---|---|
| SSM 52722 | 2024-08-06. Service bulletin. UNKNOWN OR OTHER. Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various FordPass/LincolnWay connectivity concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software |
| SSM 52704 | 2024-08-05. Service bulletin. UNKNOWN OR OTHER. Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt. |
| SSM 52675 | 2024-07-03. Service bulletin. UNKNOWN OR OTHER. Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level |
| SSM 52633 | 2024-07-03. Service bulletin. UNKNOWN OR OTHER. Some 2020-2024 Escape/Corsair, 2021-2024 Bronco Sport/F-150, and 2022-2024 Maverick vehicles may exhibit a condition where the door(s) do not open using the exterior door handle(s). This may be due to an enabled door reinforcement inertia lock within the exterior door handle. This condition occurs when the doors are closed or opened with excessive force. To correct this condition, follow the door reinforcement inertia lock rest procedure that has been added to Section 501-14 of the Workshop Manual under General Procedures. For claiming, use causal part 78219A64. |
| 23N06 | 2024-07-02. Service bulletin. ENGINE. Certain 2021-2022 Model Year Corsair, 2020-2022 Model Year Escape and 2022-2023 Model Year Maverick Vehicles Equipped With 2.5L HEV/PHEV Engine Long Block Replacement In some of the affected vehicles, after safety recall 23S27 has been performed, the Malfunction Indicator Light (MIL) may illuminate and store Diagnostic Trouble Codes (DTCs) P1061 and/or P032F. This could be due to a faulty connecting rod bearing that was detected by the Powertrain Control Module (PCM). |
| TSB 24-2182 | 2024-06-13. Service bulletin. UNKNOWN OR OTHER. This article supersedes TSB 23-2307 to update the Service Procedure and vehicle model years affected. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software. |
| SSM 52543 | 2024-05-23. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2024 F-150-3.5L FHEV, 2020-2024 Explorer 3.3L FHEV, 2020-2024 Escape 2.5L FHEV, and 2022-2024 Maverick 2.5L FHEV vehicles may exhibit an illuminated MIL with DTC P237F and/or P2C23 stored in the powertrain control module (PCM) and no affect on drivability. This may be due to seal damage, corrosion and/or water intrusion in the exhaust coolant temperature (ECT) sensors 3 and/or 4 connector. Visual inspection should be completed on ECT3 and ECT4 sensors and mating connections for seal damage, water intrusion, and corrosion. If seal damage, water intrusion or corrosion is present, repair per cell 5 of the Wiring Diagram, then apply Motorcraft® XG-12 Electrical Grease to the female/vehicle side of the harness. This inspection of ECT3 and ECT4 sensors should be completed prior to starting the appropriate pinpoint test in Section 303-03 of the Workshop Manual (WSM). If DTCs P237F and/or P2C23 do not return, no further action is necessary and the replacement of the entire exhaust heat exchanger assembly is not required. If P237F and/or P2C23 returns, follow the pinpoint test in Section 303-03 of the WSM for further diagnostics. |
| SSM 52516 | 2024-05-17. Service bulletin. EXTERIOR LIGHTING. Some 2022-2024 Maverick vehicles may exhibit a condition where the rear lamp assemblies do not fit tightly or have a large gap to the body. Ford is aware of the concern and this condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and a solution for this condition is expected by 3th quarter of 2024. Replacement of the rear lamp assemblies and/or retaining grommets will not resolve this condition. Monitor OASIS for additional information and schedule a service appointments for customers once the repair becomes available. |
| SSM 52476 | 2024-05-03. Service bulletin. EQUIPMENT. All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad. |
| SSM 52431 | 2024-04-25. Service bulletin. UNKNOWN OR OTHER. Some 2022-2024 Maverick vehicles equipped with 2 wheel drive (2WD) may exhibit a rattle noise from the instrument panel. Ford is aware of the concern and this condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by the end of July 2024. Monitor OASIS for additional information and schedule a service appointments for customers once the repair becomes available. |
| SSM 52410 | 2024-04-24. Service bulletin. UNKNOWN OR OTHER. Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed. |
| 23L05 | 2024-04-02. Service bulletin. EQUIPMENT:ELECTRICAL. Special Field Action 23L05 Certain 2022 - 2023 Model Year Bronco Sport, and Certain 2023 Model Year Maverick Vehicles Mobile Hot Spot Credit |
| SSM 52335 | 2024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed. |
| SSM 52314 | 2024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure. |
| SSM 52307 | 2024-03-05. Service bulletin. ELECTRICAL SYSTEM. Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 52230 | 2024-02-14. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. 2023 F-150/Escape/Explorer/Maverick vehicles equipped with a full hybrid electric vehicle (FHEV) powertrain may exhibit diagnostic trouble codes (DTCs) P0A7D and/or P0DE6 and the vehicle identification number (VIN) is not recognized by the Midtronics xRC-3363 High Voltage Battery Rescue Charger. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger. To correct this condition, update the Midtronics xRC-3363 High Voltage Battery Rescue Charger to the latest software level by navigating to the Main Menu > Settings > About (i) then selecting the download button in the bottom right corner of the tool's screen. |
| SSM 52229 | 2024-02-14. Service bulletin. ELECTRICAL SYSTEM. 2020-2023 Escape/Explorer, 2021-2023 F-150 and 2022-2023 Maverick vehicles equipped with a full hybrid electric vehicle (FHEV) powertrain may exhibit a cable connection error screen from the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The xRC-3363 will prompt the technician to verify the low voltage connections, when no actual fault is present. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger. To correct this condition, update the Midtronics xRC-3363 High Voltage Battery Rescue Charger to the latest software level by navigating to the Main Menu > Settings > About (i) then selecting the download button in the bottom right corner of the tool's screen. |
| SSM 52201 | 2024-01-30. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Some 2020-2023 Escape, 2021-2023 Corsair vehicles equipped with 2.5L engine full hybrid electric vehicle (FHEV) and plug-in hybrid electric vehicle (PHEV) powertrain and 2022-2023 Maverick vehicles equipped with 2.5L engine FHEV powertrain may exhibit a condition where the 12V battery voltage is low or discharged with diagnostic trouble code (DTC) U3003:62 stored in the direct current/direct current (DC/DC) converter control module. The vehicle may also exhibit DTC U3003:16 and/or U3000:04 stored in the DC/DC converter control module. This may be due to an open in the 300 amp high-current fuse F4 located in the high-current battery junction box (BJB). To correct this condition, refer to Workshop Manual (WSM), Section 414-05 > Pinpoint Test H to verify the 300 amp high-current fuse condition. If the high-current fuse is found to be open, replace the high-current fuse per the application listing in the parts catalog. Recharge and test the 12v battery. For repairs under warranty, use the base part number of the component that caused the damage to the fuse. |
| SSM 52065 | 2023-11-21. Service bulletin. EQUIPMENT. Some 2022-2023 Maverick vehicles equipped with hard, soft or roll-up bed covers accessories may exhibit a water intrusion into the pickup box floor. These accesories are not designed to be waterproof. Do not perform any repairs or submit a warranty claim for this condition |
| SSM 52051 | 2023-11-15. Service bulletin. POWER TRAIN. Some 2019-2023 Edge/Nautilus and 2022-2023 Maverick vehicles equipped with all wheel drive (AWD) may exhibit chatter/shudder during low speed turning events. This may be due to fluid contamination in the rear drive unit (RDU). Drain and refill the RDU, refer to Workshop Manual Section (WSM) 205-02. Drive for 5 miles (8 km) in stop and go conditions with right and left turns and re-evaluate. If the issue is still present, continue with normal WSM diagnostics. For claiming, use causal part 4000. |
| SSM 52024 | 2023-11-04. Service bulletin. HYBRID PROPULSION SYSTEM; ENGINE AND ENGINE COOLING. Some 2020-2023 Escape/2021-2023 Corsair equipped with 2.5L engine full hybrid electric vehicle (FHEV) and plug-in hybrid electric vehicle (PHEV) powertrain and 2022-2023 Maverick vehicles equipped with 2.5L engine FHEV powertrain may exhibit a condition where the 12V battery voltage is low or discharged with diagnostic trouble code (DTC) U3003:62 stored in the direct current/direct current converter control module (DC/DC). The vehicle may also exhibit DTC U3003:16 and/or U3000:04 stored in the DC/DC module. This may be due to an open in the 300 amp high-current fuse F4 located in the high-current battery junction box (BJB). |
| SSM 51998 | 2023-11-03. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS: AIR BAG/RESTRAINT CONTROL MODULE; AIR BAGS: AIR BAG/RESTRAINT CONTROL MODULE:SOFTWARE. Some 2023 Escape/Corsair vehicles built on 6-Apr-2023 and through 11-May-2023 and 2023 Bronco Sport/Maverick vehicles built on 30-Jan-2023 and through 6-Jun-2023 may exhibit an illuminated air bag warning indicator with DTC B0082:1A stored in the restraints control module (RCM). This may be due to an issue with the passenger seatbelt retractor at connector C303B. If a connection issue is found, replace the passenger front seatbelt retractor and pretensioner assembly before attempting a wiring repair. This issue does not affect the proper operation of the air bags, retractor and pretensioner. Refer to the Workshop Manual (WSM), Section 501-20A Seatbelt Systems > Removal and Installation. For claiming, use causal part 78611B08 and applicable labor times in Section 12 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 23-2315 | 2023-11-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2023 Maverick vehicles built on or before 11-Apr-2023 and equipped with a 2.5L full hybrid electric vehicle (FHEV) powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2282. This may be due to the software in the powertrain control module (PCM). To correct this condition, follow the Service Procedure to reprogram various modules starting with the PCM. |
| TSB 23-2307 | 2023-11-02. Service bulletin. UNKNOWN OR OTHER; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.