Service bulletins for the 2023 Ford F-550
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
284 on file from NHTSA, as of 2026-10-19.
About P2704 on the 2023 Ford F-550: what the code means, and the bulletins and recalls about the same components.
By type
By component
By trouble code
By topic
Only bulletins with trouble code: P2704 are shown. Show all
| TSB 26-2375 v2 | 2026-10-13. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM; POWER TRAIN. NOTE: This bulletin has been updated, refer to the change log at the bottom for details. Issue: Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: • Poor shift quality • Illuminated powertrain malfunction (wrench) indicator with DTCs P2704 and P0771 stored in the PCM / TCM . This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing theinput shaft O-rings to become damaged resulting in an open E clutch circuit. Action: For vehicles that meet all of the criteria in the Issue and Model statements, follow the Service Procedure toreprogram the PCM / TCM and/or replace the E clutch hub and input shaft O-rings |
|---|---|
| TSB 26-2375 | 2026-08-19. Service bulletin. POWER TRAIN; ENGINE; ELECTRICAL SYSTEM. This article supersedes TSB 26-2050 to increase the labor operation allowance of labor operations A and B. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2704 and P0771 stored in the PCM/TCM. This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. Additional model information: 6.7L Diesel Engine 2022-2024 F-550 or F-600 F-Super Duty vehicles built on or before 15-May-2024 with over 5,000 miles (8,000km) |
| TSB 26-2086 | 2026-03-10. Service bulletin. POWER TRAIN. Some of the vehicles listed in the Model statement above may exhibit poor shift quality with an illuminated powertrain malfunction (wrench) indicator and diagnostic trouble codes (DTC) P2704 and P0771 stored in the transmission control module (TCM). This may be due to the software in the TCM. Additional model information: 6.7L Diesel Engine 2023-2024 F-Super Duty F-250/F-350/F-450 2024 F-Super Duty F-550/F-600 built on or after 16-May-2024 |
| TSB 26-2050 | 2026-02-17. Service bulletin. POWER TRAIN. This article supersedes TSB 24-2142 to update the Parts List, Service Procedure (Steps 1-2), and increase the labor operation allowances to reprogram the PCM/TCM. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2704 and P0771 stored in the PCM/TCM. This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. Additional model information: 6.7L Diesel Engine 2022-2024 F-550 or F-600 F-Super Duty vehicles built on or before 15-May-2024 with over 5,000 miles (8,000km) |
| TSB 24-2142 | 2024-06-12. Service bulletin. POWER TRAIN. This article supersedes TSB 23-2376 to update the Part List and the Service Procedure. Some 2022-2024 F-550 and F-600 F-Super Duty vehicles equipped with a 10R140 automatic transmission and 6.7L diesel engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the transmission control module (TCM) with poor shift quality and over 5,000 miles (8,000 km) in service. This may be due to wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. To correct this condition, follow the Service Procedure to replace the E clutch hub and input shaft O-rings. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.