WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Ford F-450

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

250 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 500392021-09-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
TSB 21-21922021-09-02. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2019 F-Super Duty/F-650/F-750 vehicles equipped with a 6.7L may exhibit an engine oil leak. This may be due to the mating surface of the upper oil pan and the engine block. An oil leak in this area may also be influenced by a blocked crankcase oil vent separator. To correct the condition, follow the Service Procedure to reseal the engine block.
SSM 499892021-08-02. Service bulletin. POWER TRAIN. Some 2017-2022 F-Super Duty vehicles equipped with four-wheel drive (4WD) may exhibit steering bind or front driveline noise because the hublocks do not automatically disengage immediately following a shift from 4WD to two-wheel drive (2WD). This may be due to driveline tension between the axle and hub keeping them engaged. To correct the condition, shift the vehicle from DRIVE to REVERSE to release the driveline tension. This is a normal operating characteristic of the vehicle and replacement of the hublocks is not recommended. If the concern remains after shifting into REVERSE and allowing the vehicle to move approximately 5 feet (1.5 meters), remove and inspect the hublocks for any damage. Refer to Workshop Manual (WSM), Section 308-07A. Repair as necessary.
TSB 21-22362021-08-02. Service bulletin. SEATS. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
TSB 21-22232021-08-02. Service bulletin. POWER TRAIN. Some 2018-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P2459, P245A and/or P259F stored in the powertrain control module (PCM). This may be due to the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.
TSB 21-22222021-08-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P208E stored in the powertrain control module (PCM). This may be due to the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.
TSB 21-22072021-08-02. Service bulletin. LATCHES/LOCKS/LINKAGES:ELECTRONIC LOCK/LATCH ACTUATOR. Some 2019-2020 F-150 and F-Super Duty vehicles may exhibit one or more power door locks inoperative. This concern may be due to a power door lock actuator. To correct the condition, follow the Service Procedure steps to replace the affected actuator.
20M042021-08-02. Service bulletin. LATCHES/LOCKS/LINKAGES. On your vehicle, moisture and water entering a power door lock actuator housing could cause the actuator motor to momentarily freeze in cold temperatures and may also cause actuator motor corrosion over time. Frozen water within a power door lock actuator housing or corrosion of the power door lock actuator motor could result in an inoperative power door lock function on the affected door.
SSM 498812021-07-02. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2017-2019 F-Super Duty vehicles equipped with the factory 5th-wheel gooseneck hitch prep package may require replacement of the pickup bed. The 2020 F-Super Duty pickup beds have superseded the 2017-2019 F-Super Duty pickup bed and the existing rear bed plug/connector housing is not interchangeable with the new style pickup bed. To correct the condition, order and install wiring harness LC3Z-13A576-H, which contains the new style connector housing.
SSM 498462021-07-02. Service bulletin. FUEL SYSTEM, GASOLINE. Some 2017-2019 F-Super Duty/F-650/F-750 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P24D1 stored in the powertrain control module (PCM). To correct the condition, replace the particulate matter sensor. Refer to Workshop Manual (WSM), Section 303-14. For F-650/F-750 vehicles, use LC4Z-5L216-A. For F-Super Duty pickup and 203" wheelbase chassis cab vehicles, use LC3Z-5L216-C. For F-Super Duty 145/179/192" wheelbase chassis cab vehicles, use LC3Z-5L216-B. For F-Super Duty 168/169/193/205" wheelbase chassis cab vehicles, use LC3Z-5L216-A. For claiming, use causal part 5L239 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-21992021-07-01. Service bulletin. EQUIPMENT. This article supersedes TSB 21-2144 to update the vehicle model years affected and the Part List. Some 2015-2020 F-150 and 2017-2021 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM). To correct the condition, follow the Service Procedure steps to remove the climate control housing and replace the temperature door actuator(s) and/or lubricate the temperature blend door bearing surface.
21M042021-07-01. Service bulletin. LATCHES/LOCKS/LINKAGES. In some of the affected vehicles, moisture and water entering a power door lock actuator housing can cause the actuator motor to momentarily freeze in cold temperatures and may also cause actuator motor corrosion over time. Frozen water within a power door lock actuator housing or corrosion of the power door lock actuator motor could result in an inoperative power door lock function on the affected door.
TSB 21-21752021-07-01. Service bulletin. ELECTRICAL SYSTEM. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.
TSB 21-21442021-06-03. Service bulletin. EQUIPMENT. Some 2015-2021 F-150 and 2017-2021 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM). To correct the condition, follow the Service Procedure steps to remove the climate control housing and replace the temperature door actuator(s) and/or lubricate the temperature blend door bearing surface.
SSM 498202021-06-01. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2017-2021 Ford and Lincoln vehicle owners may experience a condition of missing Authorization, Command and Control, Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.
SSM 498052021-06-01. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING. Some 2011-2021 vehicles equipped with a diesel engine may have engine oil in the exhaust after turbocharger replacement for various reasons. To correct the condition, remove the exhaust and stand the exhaust up with the turbocharger inlet side facing down using a suitable drain pan. Allow the exhaust to drain for at least 24 hours and reinstall. Do not perform a manual exhaust regeneration.
SSM 498032021-06-01. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 497952021-06-01. Service bulletin. COMMUNICATION:MANUFACTURER TELEMATICS; ELECTRICAL SYSTEM. Some 2018-2021 Ford and Lincoln vehicles may not be able to perform remote commands via the FordPass/LincolnWay App due to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
CSR 5162021-05-28. Service bulletin. ENGINE AND ENGINE COOLING. Ford Motor Company has issued an emissions recall on certain 2018 model year F-150, 2019 model year F-250 through F-550 Super Duty, and 2019 model year F-650 through F-750 medium duty Ford vehicles equipped with a diesel engine. Contact your local Ford dealer to schedule a service date to perform the recall. Refer to the included communication from Ford for additional information. Altec is not able to complete this repair. All work must be completed by an authorized Ford dealer.
SSM 497562021-05-03. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Some 2018-2021 vehicles supported by FDRS may not list a software update for a module under the SW Updates tab although an SSM or TSB is published for a software update. This may be due to the module already being at the latest software level. A later software level may have been programmed at the assembly plant, during a previous dealer visit or by an over the air (OTA) update for vehicles that have automatic updates enabled in the SYNC system settings. To review a vehicle's OTA update history, visit the Connected Vehicle > OTA Dashboard tab in OASIS. Information about the OTA Dashboard can be found on FMCDealer.com when performing a search on OTA History Job Aid.
SSM 497402021-05-03. Service bulletin. STEERING. Some 2017-2021 F-Super Duty four-wheel drive (4WD) vehicles may have a customer concern of intermittently exhibiting excessive steering oscillation. To correct the condition, replace the steering damper with KC3Z-3E651-B and return the vehicle to the customer. For claiming, use causal part 3E651 and applicable labor operations in Section 03 of the Service Labor Time Standards (SLTS) Manual. If the concern returns, refer to the updated procedures, with videos, in Workshop Manual (WSM), Section 211-03 Steering Linkage > Diagnosis and Testing > Symptom Chart.
SSM 497222021-05-03. Service bulletin. WHEELS. Some 2017-2021 F-Super Duty vehicles equipped with dual rear wheels (DRW) and 17 inch aluminum wheels may require valve stem replacement for the front wheels. The parts catalog has been updated to use service part F2GZ-1700-D for the front wheels.
TSB 21-20742021-04-03. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P208E, P2459, P245A and/or P259F stored in the powertrain control module (PCM). This may be due to the PCM software. To correct the condition, follow the Service Procedure to reprogram the PCM.
TSB 21-20522021-04-03. Service bulletin. EQUIPMENT. Some 2017-2021 F-Super Duty vehicles equipped with a 6.7L diesel may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2459, P246C and/or P2463 with a Drive to Clean maintenance message. Vehicles operated primarily in a stationary or off-highway low speed use may exhibit frequent exhaust regeneration attempts. In these conditions, a vehicle may not easily allow for normal exhaust regeneration and may benefit from operator commanded regeneration (OCR) capability so it can perform complete exhaust regeneration in a stationary setting.
SSM 497082021-03-31. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2019 F-150/F-Super Duty/Expedition/Navigator and 2020 Explorer/Aviator vehicles may exhibit a 'Trailer Connected' or 'Trailer Disconnected' message in the vehicle's message center with no trailer attached to the vehicle. To address this condition, reprogram the trailer module (TRM) using the appropriate Ford diagnostic scan tool. For claiming use causal part 19H332 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.