WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Ford F-250

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

244 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 514522023-04-05. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 F-150, 2021-2023 F-Super Duty, 2021-2023 Ranger customers may have concerns including, but not limited to: no power to the distribution box, rear camera inoperative, rear park assist inoperative, box lights inoperative, power up/down tailgate inoperative, unable to open tailgate by tailgate switch, and no tailgate ajar message when the tailgate is ajar. These concerns may be caused by faulty connections between the pickup bed, tailgate, rear lamp assemblies, or bumper where connectors are disconnected, damaged, or coated with bedliner. Prior to performing any warranty diagnosis or repairs, verify if the vehicle had an aftermarket spray-in-bedliner. Any repairs resulting from aftermarket products/installation, including but not limited to a spray-in bedliner, are not covered under warranty.
SSM 514492023-04-05. Service bulletin. EQUIPMENT:ELECTRICAL. Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 514322023-04-04. Service bulletin. PARKING BRAKE. Some 2020-2022 F-Super Duty vehicles may exhibit a condition where the vehicle will not shift out of park (P). Diagnostic trouble codes (DTC) C0040 and/or P0504 may also be present. Reference TSB 22-2044 to make sure that no water or corrosion is present in the battery junction box (BJB). If Pinpoint Test A: Brake Shift Interlock in Workshop Manual (WSM), Section 307-05 leads to a concern with circuit SBP07 (white/red), remove the left side scuff plate from the floor and inspect circuit SBP07 for any damage. If damage is present, repair as necessary. Refer to Wiring Diagram, Cell 005. Submit a Report a Vehicle Concern form at the bottom of the OASIS screen and attach any available pictures to assist with the engineering investigation.
SSM 514072023-04-04. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Some 2021-2022 Ford and Lincoln vehicles equipped with SYNC 4 may experience an error message during the gateway module (GWM) software update application which states Procedure Unsuccessful- GetConfigDataFromGIVIS. This may be the result of a server related concern. To correct the condition, download and run the Ford Diagnosis and Repair System (FDRS) application GWM-Read the Gateway Module A (GWM) Configuration Data application. When the application completes, refresh and re-attempt the GWM-Gateway Module A (GWM) Software Update application. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 23-20822023-04-04. Service bulletin. POWER TRAIN; BACK OVER PREVENTION:SOFTWARE. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0315, P054F, P054E, P2A00, P2A01, and/or P02ED stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM and the transmission control module (TCM).
TSB 23-20772023-04-04. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); BACK OVER PREVENTION:SOFTWARE. Some 2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) U3012 stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM and transmission control module (TCM).
TSB 23-20762023-04-04. Service bulletin. POWER TRAIN. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) after various fuel system repairs. This may be due to incorrect learned values in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM, reprogram the transmission control module (TCM), and perform the Reset Minimum Fuel Mass Adaptions All Cylinders.
23P012023-03-07. Service bulletin. ELECTRICAL SYSTEM. Certain 2022 Model Year Super Duty Vehicles Equipped with Sync4 Body Control Module Software Update In some of the affected vehicles, the vehicle may enter a deep sleep state when powered off.
SSM 513302023-03-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2022 F-Super Duty vehicles equipped with a 7.3L engine may exhibit a ticking/clicking/tapping noise at idle that is loudest at the front of the engine where the front timing cover meets the oil pan. This may be due to a cracked oil pump drive gear. If the noise originates from the lower front of the engine, remove the accessory drive belt and retest. If the noise is still present, remove the oil pan and rotate the crankshaft 360 degrees to inspect for cracking. If cracked, replace the oil pump drive gear (LC3Z-6306-A).
SSM 513162023-02-02. Service bulletin. POWER TRAIN. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P1674 stored in the transmission control module (TCM). This may be due to a discharged battery and/or low battery state of charge. Before performing normal diagnostics in Workshop Manual (WSM), Section 307-01, charge and test the battery/batteries using the Ford approved battery test equipment listed in the Ford Warranty and Policy Manual. Replace the battery/batteries if directed by the test equipment. Clear DTCs and perform the self test again. If P1674 returns, refer to WSM, Section 307-01 for normal diagnostics. If P1674 does not return, use the Report a Vehicle Concern link at the bottom of OASIS to submit a report that will assist with the engineering investigation.
22OTA SU3P1SD2023-01-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Software Update 4 P1 for 2022 Model Year Super Duty vehicles is now available. Quality improvements include: - change to low power mode rearview camera distortion when the vehicle is shut off and restarted quickly without opening the vehicle doors.
22G05 S22023-01-06. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Certain 2022 Model Year F-150 and Super Duty Vehicles Exterior Badge Retrofit REASON FOR THIS SUPPLEMENT Service Action: Dealers are to order parts through the SSSC as needed. Claims Preparation And Submission: Causal part number correction. Labor Allowances: Clarification - temporary fender vent badge adjustment is for Super Duty only. Parts: Dealers are to order parts through the SSSC as needed. Correction: The small King Ranch tailgate badge does not apply to the F-150 2022 Model Year in this program.
SSM 512792023-01-06. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 F-150, 2021-2022 F-Super Duty, 2021-2023 Ranger customers may have concerns including, but not limited to: no power to the distribution box, rear camera inoperative, rear park assist inoperative, box lights inoperative, power up/down tailgate inoperative, unable to open tailgate by tailgate switch, and no tailgate ajar message when the tailgate is ajar. These concerns may be caused by faulty connections between the pickup bed, tailgate, rear lamp assemblies, or bumper where connectors are disconnected, damaged, or coated with bedliner. Prior to performing any warranty diagnosis or repairs, verify if the vehicle had an aftermarket spray-in-bedliner. Any repairs resulting from aftermarket products/installation, including but not limited to a spray-in bedliner, are not covered under warranty.
SSM 512652023-01-06. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR; EQUIPMENT. Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
SSM 512632023-01-06. Service bulletin. BACK OVER PREVENTION; STRUCTURE:BODY:DOOR. Some 2015-2023 F-150, 2017-2022 F-Super Duty, and 2019-2023 Ranger vehicles may exhibit dust ingress into the cabin through the doors or air extractors. This may be due to the climate control system being in recirculation mode as a result of the recirculation button being on or automatic strategies for heating/cooling efficiency. To minimize dust ingress when driving in off-road or secondary road conditions, make sure that all doors and windows are fully closed and the climate control system is switched to defrost on and the instrument panel and footwell air vents are switched to off. Temperature and fan settings may be adjusted as desired. Alternatively, max defrost can be activated which will adjust all settings automatically. Operating in defrost mode will keep constant air flow through the rear air extractors and other small areas, helping minimize dust ingress.
SSM 512612023-01-06. Service bulletin. SERVICE BRAKES. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 512512023-01-05. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2022 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 °F (65 °C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval.
TSB 22-24852023-01-05. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:WIRELESS CHARGER/CRADLE. Some 2020-2021 Expedition/Navigator, 2020-2022 F Super Duty/Explorer, 2021-2022 Bronco/Corsair/Escape/Bronco Sport, 2022 Maverick vehicles may exhibit the wireless charger inoperative or poor performance when using some Apple iPhone models that use MagSafe wireless charging including iPhone 12 and 13. This may be due to limited compatibility with the wireless accessory charging module (WACM). To correct the condition, follow the Service Procedure to update the WACM. Note: The WACM software is designed to improve the compatibility between some Apple MagSafe charging iPhones, including iPhone 12 and 13 models, and the Ford Qi wireless charging module.
22G05 S12022-12-02. Service bulletin. UNKNOWN OR OTHER. Certain 2022 Model Year F-150 and Super Duty Vehicles Exterior Badge Retrofit REASON FOR THIS SUPPLEMENT Service Action: Interim Service Action for temporary fender vent badge interference as needed Added details for vehicles arriving with production badges. Labor Allowances: Added labor code for temporary fender vent badge adjustment as an interim repair Added labor code for a vehicle that has production badges to close out of the program. Technical Information: Updated service details including interim actions for temporary badges
21M05 S32022-12-02. Service bulletin. LATCHES/LOCKS/LINKAGES:FUELING/CHARGING DOOR/HATCH/PORT:LATCH/LOCK RELEASE SYSTEM; UNKNOWN OR OTHER; ELECTRICAL SYSTEM:WIRING; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Certain 2017-2022 Model Year Super Duty Vehicles Equipped with a Power Release Tailgate - Unintended Tailgate Opening REASON FOR THIS SUPPLEMENT Technical Information: Updated with revised instructions to account for wiring harness changes that were implemented into production and changes to the tailgate latch control assembly removal and installation procedures. As a result, the Labor Allowances and Parts Requirements / Ordering Information have also been updated accordingly. Parts Requirements/Ordering Information: All parts are on open order. Special Service Support Center (SSSC) contact is no longer required to order tailgate actuator ground wiring kit.
TSB 22-24502022-12-02. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:SHAFT:OUTPUT; UNKNOWN OR OTHER. Some 2022 F-Super Duty vehicles built on or before 31-Jul-2022 equipped with a 10R140 automatic transmission may exhibit a fluid leak from the selector shaft seal. This may be caused by a crack in the manual shaft. To correct this condition, follow the Service Procedure to replace the manual shaft, the manual shaft-to-sensor roll pin and the selector shaft seal.
TSB 22-24432022-12-02. Service bulletin. UNKNOWN OR OTHER; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. This article supersedes TSB 22-2313 to update the Parts List, Service Procedure, and vehicle production fix dates. Some 2020-2022 F-Super Duty vehicles may exhibit a condition where the engine will not turn off and/or have various electrical symptoms including a dead battery, horn stays on and no crank/no start. The vehicle may also have an illuminated anti-lock braking system (ABS) indicator with diagnostic trouble codes (DTCs) C0020 and U3003 in the ABS module. This may be a result of water/moisture intrusion into the battery junction box (BJB). The BJB is located under the hood of the vehicle. This water/moisture intrusion may be related to the BJB cover not installed completely or broken cover tabs/locking fingers allowing water/moisture into the BJB. To correct the condition, follow the Service Procedure to inspect for water/moisture intrusion into the BJB and replace the BJB and cover if water/moisture intrusion is found.
SSM 511852022-11-30. Service bulletin. STRUCTURE:BODY:TAILGATE. Some 2015-2022 F-150 and 2017-2022 F-Super Duty vehicles may experience issues with the tailgate center step moulding. If there is an issue with the center molding (warped, damaged condition, loose, or if the molding is missing), the trim cover is now available separately. It is no longer necessary to replace the entire rear step assembly (402A48).
SSM 511702022-11-29. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an A/C system blowing only warm air. This may be due to the powertrain control module inhibiting the engagement of the air conditioning compressor clutch with parameter identification (PID) AC_INHIBIT_11 status showing TRUE. If this PID shows TRUE but the ambient air temperature PID reads correctly, this may be due to a disconnected mass air flow sensor with the ignition on, especially after checking the condition of the engine air filter. To correct the condition, clear all diagnostic trouble codes and perform the HVAC or FCIM - Reset the Outside Air Temperature Sensor Learned Values application. If the condition remains, the vehicle needs to be driven for 2-5 minutes over 23 mph (37 km/h). If the condition still remains, refer to Workshop Manual, Section 412-00 for normal diagnostics.
22G052022-11-01. Service bulletin. EQUIPMENT. Certain 2022 Model Year F-150 and Super Duty Vehicles Exterior Badge Retrofit Due to a supplier shortage of exterior vehicle badges, some 2022 Model Year F-150 and Super Duty vehicles will be shipped and can be sold to customers with temporary or missing badges. Temporary/missing badges will not impact the vehicle performance or function. Trucks may not have the same number of temporary badges and/or missing badges. All temporary badges will be molded in color black.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.