WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Ford Explorer

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

198 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 489082020-07-07. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
SSM 489342020-07-07. Service bulletin. FORWARD COLLISION AVOIDANCE: WARNINGS. Some 2018-2019 Explorer/Expedition/F-150/F-Super Duty/Taurus vehicles equipped with a forward collision warning head up display (HUD) may exhibit various warning indicators caused by a possible intermittent lack of HS2-CAN network communication. If the concern cannot be duplicated, place the vehicle in direct sunlight for 15 to 30 minutes to increase the temperature of the HUD and retest. If the concern is present, disconnect the HUD and check for proper HS2-CAN network communication. If proper HS2-CAN network communication is achieved, then HUD module replacement is likely needed. If disconnecting the HUD does not re-establish communication, the HUD is not at fault, refer to Workshop Manual (WSM), Section 418-00, PPT AL for diagnostics.
SSM 488762020-07-07. Service bulletin. WHEELS; SUSPENSION:REAR; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. For 2013-2019 Ford Explorer vehicles that require rear wheel knuckle and bushing assembly repairs, dealers are advised to follow Workshop Manual (WSM) Procedures and use service parts recommended by Ford only. Ford has received reports of toe link failures after the installation of non-OEM cross-axial ball joints (aka bushings) in the rear wheel knuckle, and if service of the rear wheel knuckle and bushing assembly is required, the recommended repair is to replace the affected 5B758/9 as an assembly only. Refer to WSM, Section 204-02, and the Ford Service Parts Catalog as needed.
TSB 20-21712020-06-05. Service bulletin. STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS; SEATS. Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 488582020-06-04. Service bulletin. ELECTRICAL SYSTEM. Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
SSM 488342020-06-04. Service bulletin. STEERING. Some 2017-2019 Explorer/Police Interceptor Utility vehicles may exhibit various noise concerns while turning. Workshop Manual (WSM), Section 211-02 Power Steering > Diagnosis and Testing is in the process of being updated with improved information to aid with accurate noise diagnosis. Replacing the steering gear may not necessarily eliminate the noise concern. Use Chassis Ears on all suspected components to accurately diagnose noise concerns. Monitor OASIS for updates.
SSM 488212020-06-04. Service bulletin. WHEELS. For 2013-2019 Ford Explorer vehicles that require rear wheel knuckle and bushing assembly repairs, dealers are advised to follow Workshop Manual (WSM) Procedures and use service parts recommended by Ford only. Ford has received reports of toe link failures after the installation of non-OEM cross-axial ball joints in the rear wheel knuckle, and if service of the rear wheel knuckle and bushing assembly is required, the recommended repair is to replace the affected 5B758/9 assembly. Refer to WSM, Section 204-02, and the Ford Service Parts Catalog as needed.
TSB 20-21542020-06-04. Service bulletin. STRUCTURE:BODY:ROOF AND PILLARS. Some 2016-2019 Explorer vehicles may exhibit roof rail covers that become loose or partially detached. This may be caused by a lack of retention of the clips securing the roof rail covers. To correct the condition, follow the Service Procedure to replace the retaining clips and apply adhesive to the roof rail covers.
SSM 487572020-05-04. Service bulletin. ELECTRICAL SYSTEM. Some customers may experience a notification in the FordPass and/or LincolnWay apps that indicates their vehicle has entered "deep sleep mode". This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".
SSM 486192020-04-02. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
SSM 485582020-03-03. Service bulletin. ELECTRICAL SYSTEM. SSM 48558 - 2017-2020 Various Vehicles Equipped With Telematics Control Unit (TCU) - Various FordPass/LincolnWay Mobile App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 484312020-02-04. Service bulletin. SEATS. Some 2016-2019 Explorer vehicles may exhibit a heated front seat that does not operate properly after turning the ignition on after a remote start event. The seat back heats properly while the lower seat cushion does not. To correct the concern, reprogram the driver seat module (DSM) using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14C708 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 484232020-01-08. Service bulletin. POWER TRAIN. Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-23902020-01-07. Service bulletin. ELECTRICAL SYSTEM; SEATS. Some 2015-2019 F-150, 2015-2020 Explorer, 2017-2019 F-Super Duty, 2017-2020 Continental, 2018-2020 Expedition/Navigator, 2016-2018 MKX, 2019-2020 Nautilus, 2020 Aviator/Corsair and 2013-2020 MKZ vehicles equipped with multi-contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.
TSB 19-23892020-01-07. Service bulletin. ENGINE AND ENGINE COOLING. Some 2013-2019 Explorer vehicles equipped with a 3.5L twin independent variable camshaft timing (Ti-VCT) engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P013A and/or P013C stored in the powertrain control module (PCM). This may be due to an improperly welded exhaust Y-pipe. To correct the condition, follow the Service Procedure to replace the exhaust Y-pipe.
tSB 19-23642020-01-07. Service bulletin. EQUIPMENT. Some 2016-2019 Explorer vehicles may exhibit roof rail covers that become loose or partially detached. This may be caused by a lack of retention of the clips securing the roof rail covers. To correct the condition, follow the Service Procedure to apply adhesive to the roof rail covers.
SSM 483402019-12-05. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
SSM 483162019-12-05. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 482792019-11-06. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2019 Ford and Lincoln vehicles equipped with a telematics control unit (TCU) may exhibit a persistent message in the Ford Pass/Lincoln Way mobile app advising, Your vehicles software is being updated. Vehicle controls will be unavailable for about 10 minutes while this update takes place. This may be due to the TCU still in factory mode. Using the appropriate Ford diagnostic scan tool, check the TCU_AUTHSTATE PID status showing Factory Mode. To correct this condition, perform programmable module installation (PMI) on the telematics control unit (TCU). Once PMI is completed, ensure the TCU_AUTHSTATE PID in service tool no longer displays Factory Mode. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM) section 415-00. For claiming, use causal part 14G229.
SSM 482672019-11-05. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 482602019-11-05. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
DOR-J9K8E-102019-10-21. Service bulletin. SUSPENSION. This SKU is a Suspension Lateral Link. The customer communication requested return of unsold inventory to revise the design similar to the OEM supercession associated with 19V435. We have received no defects associated with the current design.
TSB 19-22932019-10-04. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST; SEATS. Some 2015-2019 F-150/Explorer, 2017-2019 F-Super Duty/Continental, 2018-2019 Expedition/Navigator, 2016-2018 MKX, 2019 Nautilus, and 2013-2019 MKZ vehicles equipped with Multi-Contour seats may exhibit intermittent multi-contour seat operation and/or massage and lumbar adjust inoperative from the seat switch or SYNC screen with or without diagnostic trouble code (DTC) B1471, U024B, and/or U024C. This may be due to terminal fretting at the connector for the driver multi-contour seat module (SCMG) and passenger multi-contour seat module (SCMH). To correct the condition, follow the Service Procedure steps to replace the connectors and reroute the harness.
SSM 481352019-09-09. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 481302019-09-06. Service bulletin. VISIBILITY:GLASS, SIDE/REAR; VISIBILITY. Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.